Windows 7 Forums

Welcome to Windows 7 Forums. Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks.


Windows 7: Can't open system recovery?

08 Oct 2013   #1
TyGuy96

Windows 7 Home Premium 64bit
 
 
Can't open system recovery?

I started up my old HP mini 210 today and it seemed slow. I powered it off and back up to find that it had a problem starting windows. Now every time I restart it, I get 2 options:
1) Launch Startup Repair (Recommended)
2) Start Windows Normally

2 just restarts my computer, bringing me back to that screen, and 1 starts up recovery manager. In the recovery manager window, The "I need help immediately" section and "I'd like to take precautions" section are both disabled. The only option I can choose is "Run Computer Checkup" where I can open the command prompt. I don't have the windows installation disk.

Any idea on how I can restore the system? There is no files I need on the computer, so I can delete whatever.

Thanks


My System SpecsSystem Spec
.

08 Oct 2013   #2
Anak

Microsoft Community Contributor Award Recipient

Win 7 Home Premium 64bit Ver 6.1.7600 Build 7601 - SP1
 
 

Hi TyGuy96, welcome to 7F!

Can you restart your mini and while that's happening, reboot into "Last Known Good Configuration"?

See:Advanced Boot Options Usually you need to tap the F8 button while it's rebooting, but your system maybe different.

You may need Here's How Step #3 if you only have the one operating system on the mini. Once you make the selection let your mini reboot, then see how its reacting.
My System SpecsSystem Spec
08 Oct 2013   #3
TyGuy96

Windows 7 Home Premium 64bit
 
 

When I start the mini, this screen pops up:


When I click the button in the bottom left, it starts booting up windows. I press F8, but it just brings up the 2 options I mentioned before. There is no "Last Known Good Configuration".
My System SpecsSystem Spec
.


09 Oct 2013   #4
Anak

Microsoft Community Contributor Award Recipient

Win 7 Home Premium 64bit Ver 6.1.7600 Build 7601 - SP1
 
 

What version of Mini 210 is this, a 1040nr?

Have you tried getting to system recovery this way?How to Perform an HP System Recovery | HP® Support
My System SpecsSystem Spec
09 Oct 2013   #5
TyGuy96

Windows 7 Home Premium 64bit
 
 

I have the hp mini 210-1071CA.
When I try that recovery method, after I press F11 it takes me to the screen I mentioned in option 2.

Edit: Bump
My System SpecsSystem Spec
10 Oct 2013   #6
Anak

Microsoft Community Contributor Award Recipient

Win 7 Home Premium 64bit Ver 6.1.7600 Build 7601 - SP1
 
 

From: Computer Does not Start (Windows 7, Vista, XP) HP Mini 210-1071CA PC | HP® Support Let's try the first step, the hard reset.

If you'd like a more visual approach: Computer Does Not Start Up or Boot Properly - HP Support Center
Still, stay with the hard reset, but if you see any other steps that fit your situation please try them.

This could be a power problem, how long has it been since you started the mini last? You might have to run it strictly on AC power for a while before you depend on the battery.


Manuals for HP Mini 210-1071CA PC | HP® Support
My System SpecsSystem Spec
10 Oct 2013   #7
TyGuy96

Windows 7 Home Premium 64bit
 
 

Yes, that is my machine.
Windows 7 Starter 32-bit is on it.
No SSD. 160Gb HDD.

The hard reset didn't change anything.
I haven't started the mini in a few months (probably 8 at the most), and it was dead when I first tried turning it on. It has been running off of AC since then.
My System SpecsSystem Spec
10 Oct 2013   #8
Anak

Microsoft Community Contributor Award Recipient

Win 7 Home Premium 64bit Ver 6.1.7600 Build 7601 - SP1
 
 

My System SpecsSystem Spec
10 Oct 2013   #9
TyGuy96

Windows 7 Home Premium 64bit
 
 

Yes, I held it for at least 15 seconds.
No, I am not getting any error messages.
There are no beeps/blinks. I'm not sure what you mean by "memory modules.

I noticed that when I select start windows normally, that it starts loading, then the BSOD flashes then the HP restarts.
My System SpecsSystem Spec
10 Oct 2013   #10
Anak

Microsoft Community Contributor Award Recipient

Win 7 Home Premium 64bit Ver 6.1.7600 Build 7601 - SP1
 
 

Memory modules are the ram sticks in your mini, did you see the explanation below the "beep codes"?


Quote:
Check for loose connections and test the memory

Blink codes are often displayed after a user adds memory to the computer but does not seat the module properly. The LEDs may also blink error codes if a hardware component is loose because the computer was dropped or jarred. Some HP Notebook PCs come with one stick of memory but have two memory slots. The problem could be that the stick of memory or one of the memory slots has a bad connection.

The memory module compartment on most notebooks is located on the bottom of the case. The exact position varies by model. However, on some models, the memory compartment is under the keyboard. See your User Guide for the exact location of memory modules on your notebook.

NOTE: Removing and reseating memory modules requires the use of tools and the partial disassembly of the computer. If you do not feel comfortable doing this work yourself, take the computer to an authorized retailer for technical service.

Check for loose memory modules


Source: Troubleshooting LED Blink Codes or Beep Codes During Startup or Boot - HP Support Center
Even if you didn't fool with the "memory", pull them out and re-seat them.
It doesn't look that hard, and shouldn't need "special tools" just pop the little door, pull them out make sure there is no corrosion and pop them back in.

Just pay attention to how they came out.


Note   Note
You said you're not getting any errors?? What is this reference to BSOD's, Is it a true BSOD blue or black screen or just a flash?

Can you get a screenshot of what it is and post it? Screenshots and Files - Upload and Post in Seven Forums



By the way, Please do not "bump" your threads, It is against Forum rules.

Quote:
2) No useless posts, e.g., thread bumping, useless one liners, junk posting to increase post count, and identical multi-postings in different forums.
Source: http://www.sevenforums.com/general-d...ease-read.html
My System SpecsSystem Spec
Reply

 Can't open system recovery?




Thread Tools





Similar help and support threads
Thread Forum
Recovery Window is Open at Every Startup
Win 7 64 Ultimate Every time I start my system a Recovery window is open. The only item in the window is ReAgent.xml. System seems to run OK. Is this significant? How can I get rid of the window? Thanks much
General Discussion
0xc000000f Recovery Error - System Recovery Discs not being processed
Hello, My computer has many corrupt files. I have done both sfc /scannow and chkdsk /r multiple times, but the corrupt files still remain. Unfortunately, my HP's recovery manager is also corrupt so I decided to do a full factory restore. Because I couldn't do a full factory restore from the...
Backup and Restore
Operating system does not show up in System Recovery Options
Hey guys. I have an Acer laptop with Windows 7 that has crashed and will not boot. I do not have a Windows 7 CD nor do I have the money to pay for one. When my computer boots up, it says "BOOTMGR IS MISSING" and I press Ctrl+Alt+Delete and it loops back around to that page. I created a System...
General Discussion
Need to create system recovery disks from RECOVERY (D:) drive
My Laptop came preloaded with Windows 7 Home Premium and I would like to create system recovery disks. I have a drive labeled RECOVERY (D:). How do I create recovery disks from this drive?
Backup and Restore
Error can't open c:\recovery.dat
I have tried to install Windows 7 Ultimate on to my Asus F7Se but keep getting the above error. I have deleted my d: partition so now I only have c: and a recovery partition. I have tried to do the upgrade option and the custom one but always get this message when it is trying to boot up. I...
Installation & Setup
Error can't open c:\recovery.dat.
I have an Asus PRO55 series, it had Vista Home Premium on it, and I tried an upgrade to Windows 7 Ultimate (32bit)...Everything went fine, but before the first user login screen comes up, it goes to Error can't open c:\recovery.dat. and then huge red text (on white screen)comes up saying ERROR: ...
Installation & Setup

Our Sites

Site Links

About Us

Find Us

Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

© Designer Media Ltd

All times are GMT -5. The time now is 08:56.

Twitter Facebook Google+



Windows 7 Forums

Seven Forums Android App Seven Forums IOS App