Windows 7 Forums

Welcome to Windows 7 Forums. Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks.


Windows 7: Cannot do image due to bad drive - HELP

18 Mar 2016   #1
AirPower4ever

Windows 7 Pro 64-bit
 
 
Cannot do image due to bad drive - HELP

So I have a problem here which I am just not able to budge. My friend gave me his hard drive (system built by Lenovo) and a new 1TB drive. He did this because he said he was seeing an error at the Windows 7 desktop stating that the drive is bad and that it is time to backup. I saw the error too, I also saw it during boot up, we had to press F1 to go in to the BIOS or F2 to proceed. F2 and we get to the desktop only to be greeted with another error pop up about backing up.

So I said I would help, but I am not getting anywhere. This is what I have done so far;

* Start > Computer > right mouse click the C: and schedule a repair. I reboot and it does it with no errors
* Back after reboot, I did a command prompt as admin and ran chkdsk. Again, reading the results it says all is well. I reboot
* Back again, this time I rebooted again, did F8, launch command prompt and ran both chkdsk /f C:, rebooted and did the same thing, but typed chkdsk /r

During those two nothing appears to be wrong, no errors or repairs like I have seen before in my past.

So then I boot again and I try to "clone" the drive (which is 320GB) to the 1TB using Macrium (latest version) and I get an error. I checked their forums and it bascially says that it is a hard drive issue. So I go back and do all the steps mentioned and then this time I just wanted to image the drive. Same thing, I get an error about the drive. Error 23 I believe.

Is there anything else I can do to image or clone this drive?


My System SpecsSystem Spec
.
19 Mar 2016   #2
pbcopter

Windows 7 Ultimate x64 SP1, Windows 8.1 Pro x64, Windows 10 Pro x64
 
 

You could try booting to the Macrium CD and create an image of the drive from there.

Also, have you tested the drive with the manufacturers test software?
My System SpecsSystem Spec
19 Mar 2016   #3
hazel123

Windows 7 64 bit, Windows 7 32 bit and Xubuntu
 
 

I'm not an expert but did you run sfc /scannow? That might fix some Windows errors. My hard drive is on its way out and I had errors fixed by sfc /scannow and then ran chkdsk afterwards and had some bad sectors sorted. I was then going to clone it but bottled out thinking I might clone some errors (after first cloned disk had errors, hence me running sfc scannow to fix them!). So I did a clean install on the new drive. The main thing is to get your files backed up off the disk I guess.
My System SpecsSystem Spec
.

20 Mar 2016   #4
AddRAM

Windows 7 Pro x64 Windows 10 Pro x64
 
 

I would not clone or make an image of a bad drive, just buy a new drive (preferably an SSD) and reinstall windows on that.

You will do nothing but carry over problems and waste your time.
My System SpecsSystem Spec
20 Mar 2016   #5
AirPower4ever

Windows 7 Pro 64-bit
 
 

I tried the sfc /scannow and it found problems but could not fix them. I ran the commands chkdsk /f and /r and they too found problems but cannot fix them.

I think my only option is what "AddRAM" says, new drive and install again. Gotta break the news....

Thank you everyone for responding and helping out.
My System SpecsSystem Spec
20 Mar 2016   #6
hazel123

Windows 7 64 bit, Windows 7 32 bit and Xubuntu
 
 

It's worth it when it's all done! And you'd have a speedier system. I had to put a slow Sata II drive in mine because Sony wouldn't let it work with anything else - and it still seems faster after the reinstall
My System SpecsSystem Spec
Reply

 Cannot do image due to bad drive - HELP




Thread Tools Search this Thread
Search this Thread:

Advanced Search




Similar help and support threads
Thread Forum
New hard drive using less space after image restore then old drive?
My old Seagate 1TB hard drive was filled to 780GB out of the 1TB. Since I was getting close to filled I upgraded to a WD Black 2TB. I used the Windows 7 back up to create a complete system image. I replaced the hard drive with the WD then did a system restore from the image. Everything works fine...
Backup and Restore
image an mbr drive to a gpt drive will work when using WinPE?
I want to use an imaging program to backup my system drive, for example EaseUS Todo Backup (free). My C: system drive is an MBR type (NTFS) of less than 500GB. I was figuring my backup drive to be a similarly sized (slightly larger just in case) partition on a 4TB external drive, which necessarily...
Backup and Restore
Using System Image to replace 750GB Drive with s 500GB Drive
BACKGROUND My 750gb hard disk is failing on a HP laptop that came preloaded with W7 home prem. I have a SMALLER excellent 500gb, 7200 rpm hard disk that I'd like to replace the failing hard disk with. I've read that my W7 System Repair DVD will not restore my recent system image (on NAS) to a...
Backup and Restore
cd rom drive no image help!
when i go in my computer theres only the drive c image and nothing else but if i go check my cd rom drive it says its working fine i just dont know how to be able to have it in ''my computer'' cuz right now if i put a cd in it doesnt even load or show that i did put a cd in o.O so help would be...
Hardware & Devices
drive image
Hi I want to do a drive image on my Windows 7 laptop, i bought an external USB hard drive to do it. can you surgest how to do it please?
Software


Our Sites

Site Links

About Us

Find Us

Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

Designer Media Ltd

All times are GMT -5. The time now is 08:18.

Twitter Facebook Google+



Windows 7 Forums

Seven Forums Android App Seven Forums IOS App