New
#11
Oh yes,
In the meantime, downlload, burn to CD and run following
Memtest86+ - Advanced Memory Diagnostic Tool
so that we can rule out intermittent memory problems.
Oh yes,
In the meantime, downlload, burn to CD and run following
Memtest86+ - Advanced Memory Diagnostic Tool
so that we can rule out intermittent memory problems.
reset bios to defaults...windows locked up
verified green lan is disabled...windows locked up
onboard audio disabled...windows locked up
dxdiag...passed test...windows locked up
unplugged 1 fan header that was in use on mobo...windows locked up
unchecked restart in hopes of getting bsod...no such luck..windows locked up
as far as things in startup there is only jm36 ide and realtek (this is still fresh install)
What i find even more frustrating is that I can hear the hard disk running and have network connectivity...which makes me think display driver or card...but keep in mine I have test a different video card from ati in same slot and another slot with same results...
oh my nerves....
I have already ran memtest for hours with no error detected and have swapped out memory modules with known good from my rig...same result
I'm going to ask a silly question, since this is a home built did you make sure the memory was compatible w/mother board and i5-750 before you bought it. Sometimes if it's the wrong front side bus it will not work, i5-750 may work w/1066 ram and not 1333, these are just possibilities of why it's locking up
Optomized default bios settings will not always work.
Make sure that the cpu is at correct MHz and voltage. That would be manufactureres specs!
Make sure the ram is at right MHz, initial timings and voltage. Manufacturers specs!
Look at what the mobos bios auto settings say. If they are different than specs, manually set specs to manufacturers specs.
Manufacturers Specs, I can not say this enough.
The vid card pci-e slot, set to 100.
I used a Stryker Extreme once, they all exhibited these symptoms at one time or another. I RMA'ed 4 times. The 3rd time they sent me a new retail box. The mobos all failed. Dam hard to test a mobo at home.
I just installed a Gigabyte EP45 UD3R as its replacment. I had to get bios at latest version, F12, and manually set them to hardware specs. I swapped every piece of hardware to the Gigabyte. Did not like the hardware till all specs manually input, fyi.
Basically, leave no decisions for mobo to make, you tell it.
I would begin checking out if Gigabyte has advanced RMA available. Maybe have them send you another before this one makes you crazy.
The bios is set to all of its defaults specs. (no overlocking)
The memory is not on the recommended list, but i have manaully made the changes in bios for clock speeds and timing that are...
I have an i7 rig that i suppose i could swap out the power supply and cpu on that way it it still acts up it has to be an issue with the mobo...
Does anyone else have any further input?
Could you clarify what I inked in red?
Your choice of ram may not be on the mobo's QVL, but you must use the
MHZ, timings and voltage for the ram that you are using. You can not just set the bios to a QVL setting and then put in some ram sticks.
(QVL=quality vendors list)
The above intimates that, if I miss read sorry.
Is your CPU at spec'ed MHz and voltage. When I used the default settings with my EP45 it clocked the 2.13MHz cpu to 2.66MHZ. I failed to notice immediately, I assumed defaults were...................................
sorry if that was unclear...The memory is not on the mobo vendors QVL list. The mother board did not detect the correct timing, voltage, or bus speed. I made the changes to match the memory specs.
This was not my build I am trying to help a buddy out that is at witts end with this build and I am getting close.
I have personally built over 50 PC's over the years and lets be honest...90% of us out there dont buy what's on the QVL list...and most mobo's are just fine with it...How ever maybe gigabyte is sensitive to this...this would not have been my first choice for mobo's...
The CPU is at is stock speeds and all over clocking is disabled and voltage is stock as well..
I think the RAM is the most likely cause of the issues. You can play with different combinations of voltages and timings and you might get it to be stable but it's going to take a lot of trial and error.
Systems have changed, and Core i Series computers no longer have a Northbridge. The memory controller is on the CPU and from what we see here every day, these new CPUs are very intolerant of any deviations from required parameters when it comes to RAM.