0x107 after 0xA, no pattern tho

i read somewhere about some issues with memory hole remapping .. ill turn it off and see what happens Problem using 4gb in 64 bits

also, my ram might need some tweaking, aparently there are issues running all 4 sticks on nforce boards http://www.evga.com/forums/tm.aspx?m=127243

What did you set the NB Chip voltage to?
Memory voltage?

The 'Wanna run 4x2GB on nForce board?' link is good info, did you follow all the settings he mentioned?

Most systems need some tweaking when running 4GB RAM or more, 4 RAM cards, these normally require NB (NB Chip voltage for yours) voltage and sometimes RAM voltage bumps.
More RAM chips need more voltage.

For the NB Chip voltage try the 1.313v first, if you get any crashes go to the 1.409v.

i set it to 1.4 yesterday. and it was sorta fine, but (i left the pc on all nite doing nothing) this morning, i woke up the pc, clicked on verify game cache (for another game) and got a 0x24 on ntfs.sys.
this is... annoying.

in other news
i got an email from rosewill about the psu.
i asked them, "i noticed the little table of data in the psu stating that the +12v1 is 20amp, +12v2 is 20amp, +12v3 is 30amp and the +12v4 is 30amp. which cable i need to use the 30amp since my card needs 24.
they say
use the orange 8 pin cable, but only connect 6 into your card.
with pictures and everything. so whoever has the same psu Beware:
If you own a Rosewill RBR1000-M PSU, and you need more than 20amps on your video card, you must use the orange 8 ping pci-c cable, and connect that into your card

about the settings..
the memory voltage was on 1.978v (which is the lowest) so i took it up one notch to 2.080v
i had the nb chip voltage to auto, so i moved it into 1.313v.. lets see what happens
also... how bout the cpu-nb voltage and the cpu voltage.. i currently have them on 1.4 and 1.3625

Good catch on the PSU.

Voltage settings also look good, you might need to adjust them as explained in the link you posted.


STOP*0x00000024: NTFS_FILE_SYSTEM
Usual causes:* Disk corruption, insufficient physical memory, Device driver, Indexing, Resident antivirus, backup, defrag programs, Disk/Drive failing/failure

Cause: One possible cause of this bug check is disk corruption.

Run your HDD manufacturers disk diagnostic utility.

Can you give us information on you HDD setup?

There are a lot of HDD errors on different HDDs.

Code:

Event[14]:
  Log Name: System
  Source: Disk
  Date: 2011-08-06T18:06:24.997
  Event ID: 51
  Task: N/A
  Level: Warning
  Opcode: N/A
  Keyword: Classic
  User: N/A
  User Name: N/A
  Computer: jesus-pc
  Description: 
An error was detected on device \Device\Harddisk3\DR12 during a paging operation.

Code:

Event[39]:
  Log Name: System
  Source: Ntfs
  Date: 2011-08-06T18:06:24.907
  Event ID: 137
  Task: N/A
  Level: Error
  Opcode: N/A
  Keyword: Classic
  User: N/A
  User Name: N/A
  Computer: jesus-pc
  Description: 
The default transaction resource manager on volume P: encountered a non-retryable error and could not start.  The data contains the error code.

Code:

Event[48]:
  Log Name: System
  Source: Disk
  Date: 2011-08-06T18:05:58.022
  Event ID: 11
  Task: N/A
  Level: Error
  Opcode: N/A
  Keyword: Classic
  User: N/A
  User Name: N/A
  Computer: jesus-pc
  Description: 
The driver detected a controller error on \Device\Harddisk3\DR12.

Code:

Event[53]:
  Log Name: System
  Source: Disk
  Date: 2011-08-06T18:05:24.965
  Event ID: 51
  Task: N/A
  Level: Warning
  Opcode: N/A
  Keyword: Classic
  User: N/A
  User Name: N/A
  Computer: jesus-pc
  Description: 
An error was detected on device \Device\Harddisk3\DR10 during a paging operation.

Code:

Event[164]:
  Log Name: System
  Source: Service Control Manager
  Date: 2011-08-06T17:53:01.054
  Event ID: 7023
  Task: N/A
  Level: Error
  Opcode: N/A
  Keyword: Classic
  User: N/A
  User Name: N/A
  Computer: jesus-pc
  Description: 
The VMware USB Arbitration Service service terminated with the following error: 
A device attached to the system is not functioning.

Update driver or app:
Part of a Copy Protection platform dveloped by Tages SA: http://www.tagesprotection.com/

Code:

Event[185]:
  Log Name: System
  Source: Service Control Manager
  Date: 2011-08-06T17:52:36.484
  Event ID: 7000
  Task: N/A
  Level: Error
  Opcode: N/A
  Keyword: Classic
  User: N/A
  User Name: N/A
  Computer: jesus-pc
  Description: 
The atksgt service failed to start due to the following error: 
This driver has been blocked from loading

STOP*0x00000109: CRITICAL_STRUCTURE_CORRUPTION
Usual causes:* Device driver, Breakpoint set with no debugger attached, Hardware (Memory in particular)

Code:

Event[253]:
  Log Name: System
  Source: Disk
  Date: 2011-08-06T16:30:11.609
  Event ID: 11
  Task: N/A
  Level: Error
  Opcode: N/A
  Keyword: Classic
  User: N/A
  User Name: N/A
  Computer: jesus-pc
  Description: 
The driver detected a controller error on \Device\Harddisk7\DR13.

Code:

Event[259]:
  Log Name: System
  Source: Disk
  Date: 2011-08-06T16:30:07.397
  Event ID: 51
  Task: N/A
  Level: Warning
  Opcode: N/A
  Keyword: Classic
  User: N/A
  User Name: N/A
  Computer: jesus-pc
  Description: 
An error was detected on device \Device\Harddisk7\DR12 during a paging operation.

Open Core Temp and monitor when the system is stressed, or while running Prime95.

Code:

Event[637]:
  Log Name: System
  Source: Microsoft-Windows-Kernel-Power
  Date: 2011-08-06T15:46:14.198
  Event ID: 89
  Task: N/A
  Level: Information
  Opcode: Info
  Keyword: N/A
  User: S-1-5-18
  User Name: NT AUTHORITY\SYSTEM
  Computer: jesus-pc
  Description: 
ACPI thermal zone ACPI\ThermalZone\THRM has been enumerated.             
_PSV = 346K             
_TC1 = 4             
_TC2 = 3             
_TSP = 6000ms             
_AC0 = 346K             
_AC1 = 0K             
_AC2 = 0K             
_AC3 = 0K             
_AC4 = 0K             
_AC5 = 0K             
_AC6 = 0K             
_AC7 = 0K             
_AC8 = 0K             
_AC9 = 0K             
_CRT = 348K             
_HOT = 0K             
_PSL - see event data.

NB voltage is for the motherboard NB chip, it's separate from the CPU integrated NB memory controller.

CPU-NB voltage is the CPU integrated memory controller, this voltage can be set separately from the CPU voltage.

CPU voltage is the power to the CPU, processor itself.


Let us know the HDD test results for all the HDDs. It will take a while to test them all.

the seagate test for the raid 0, each individual drive (short test) came up ok. i couldnt run the test for the raid 5 as the western digital software doesnt see them (for some reason)
i ran memtest 4.20
and got one error so far. (still running)
tst -pass failling address --------- good ------bad -------err-bits ---count chan
6-- 0 ----000ac466dc - 172.2 mb..08000000 08800000 00800000 1
5.....1.....000037dae58 - 55.8mb..00010000.00810000.00800000.2
5.....1.....000077dae38 -119.8mb.00010000.00810000.00800000.3
6.....1.....000037da69c-55.8mb...00000800.00800800.00800000.4
6.....1.....000015d269c-21.8mb...08000000.08800000.00800000.5
6.....1.....00003cd66dc-60.8mb....00100000.00900000.00800000.6
8.....1.....000058c669c-88.7mb....427b3b70.42fb3b70.008000000.7
8.....1.....0000464e6dc-70.3mb....686a9a9b.68ea9a9b.008000000.8

by using the address, how can i calculate which stick is the faulty one?
i tried hex to decimal coversion, and the first one gives me around 180, which seems close to 172.2mb, does it means it failed at the 172.2mb mark? (which is the first stick?)

so... im testing one stick at a time in the first slot.. i hope i get errors, cuz if not. it means its a slot/voltage problem.. which is harder to fix T_T