Windows 7 Forums

Welcome to Windows 7 Forums. Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks.


Windows 7: BSOD error after (nearly) completing Turbo Tax

15 Feb 2012   #1
hornsby23

Windows 7 Ultimate
 
 
BSOD error after (nearly) completing Turbo Tax

Hello,

I have a BSOD problem and need help. I'm not sure if it is directly related to Turbo Tax but this is the program that triggers the BSOD. I've had issues with this system on and off for a while, but this is the first time I've had a BSOD repeatedly, and my basic troubleshooting has not helped. I would very much appreciate any help on this. My dmp zip is attached.

Thanks in advance!

- Windows 7 x86 - Windows 7 original installed OS on the system - Full retail version - 2 years old on most of the hardware (HD that OS is installed on is older) - Age of installation: the same as above




My System SpecsSystem Spec
.
15 Feb 2012   #2
zigzag3143

Win 8 Release candidate 8400
 
 

Virtually all of these were Related to MpFilter.sys Microsoft Malware Protection Driver. Either Bitdefender or Microsoft Security Essentials. Stop using bit-defender, if MSE re-install it and update to SP-1.

I would also run these two tests.




These crashes were caused by memory corruption/exception (probably a driver).
Please run these two tests to verify your memory and find which driver is causing the problem.


* If you are overclocking anything reset to default before running these tests.
In other words STOP!!!

* If you have raid update its Driver.




Memtest.
Quote:
*Download a copy of Memtest86 and burn the ISO to a CD using Iso Recorder or another ISO burning program. Memtest86+ - Advanced Memory Diagnostic Tool

*Boot from the CD, and leave it running for at least 5 or 6 passes.

Just remember, any time Memtest reports errors, it can be either bad RAM or a bad motherboard slot.

Test the sticks individually, and if you find a good one, test it in all slots.

Any errors are indicative of a memory problem.

If a known good stick fails in a motherboard slot it is probably the slot.

RAM - Test with Memtest86+



Driver verifier

Quote:
Using Driver Verifier is an iffy proposition. Most times it'll crash and it'll tell you what the driver is. But sometimes it'll crash and won't tell you the driver. Other times it'll crash before you can log in to Windows. If you can't get to Safe Mode, then you'll have to resort to offline editing of the registry to disable Driver Verifier.

So, I'd suggest that you first backup your stuff and then make sure you've got access to another computer so you can contact us if problems arise. Then make a System Restore point (so you can restore the system using the Vista/Win7 Startup Repair feature).

Then, here's the procedure:
- Go to Start and type in "verifier" (without the quotes) and press Enter
- Select "Create custom settings (for code developers)" and click "Next"
- Select "Select individual settings from a full list" and click "Next"
- Select everything EXCEPT FOR "Special Pool", "Force Pending I/O Requests" and "Low Resource Simulation" and click "Next"
- Select "Select driver names from a list" and click "Next"
Then select all drivers NOT provided by Microsoft and click "Next"
- Select "Finish" on the next page.

Reboot the system and wait for it to crash to the Blue Screen.
Continue to use your system normally, and if you know what causes the crash, do that repeatedly.
The objective here is to get the system to crash because Driver Verifier is stressing the drivers out.
If it doesn't crash for you, then let it run for at least 36 hours of continuous operation.

Reboot into Windows (after the crash) and turn off Driver Verifier by going back in and selecting "Delete existing settings" on the first page, then locate and zip up the memory dump file and upload it with your next post.

If you can't get into Windows because it crashes too soon, try it in Safe Mode.
If you can't get into Safe Mode, try using System Restore from your installation DVD to set the system back to the previous restore point that you created.
My System SpecsSystem Spec
Reply

 BSOD error after (nearly) completing Turbo Tax




Thread Tools Search this Thread
Search this Thread:

Advanced Search




Similar help and support threads
Thread Forum
BSOD after completing clean install win7 64
Hello, I recently completed a new build consisting all new hardware. Everything has gone fine until I installed windows. I am using, -x64, (however I notice a program files x86 on the local disk as well but not sure if it has anything to do with my problem, new to building my own...
BSOD Help and Support
i'm getting a error when i reach "Completing Installation"
first of all i have Legit W7 Ultimate and i been using my same type of OS installing since 2010 until now, i think there's nothing wrong with my system rig but maybe the HDD? its "Deskstar Hitachi 250GB" 2 year old HDD, i successfully installed my OS with it 3 months ago until a problem came were...
Installation & Setup
Can't Install Win 7 - BSOD on Completing Installation
Having problems installing Win 7 on to my computer (Abit IP35-E mobo and on to a new 1TB HDD, which I partition to 50gig for the Windows drive). It can get as far as the completing installation part (which takes ages), and then it will quickly flash a blue screen for a second and then reboot with...
Installation & Setup
BSOD while using Turbo Key setting.
When I run Flight Sim X or CoD Black Ops when using the turbo key feature, I receive STOP 0X00000124 message. I ran memtest error free for 5 passes. I ran checkdisk and passed as well. When I run Prime under the blend setting I receive bsod STOP 0X00000124 message. Please note, I am not using the...
BSOD Help and Support
[Win 7 x64] BSOD on install (during completing installation step)
Hi guys, I have been having a number of driver woes lately (BSODs), so I decided to reformat and do a clean install. But I keep on getting a MEMORY_MANAGEMENT BSOD as it was completing the setup. I tried 3 times, it happened 3 times, like clockwork. I have heard that there is a problem with...
Installation & Setup
Error when completing installation
Hi! I've been trying to install win7 for like 3-4 times now and every time I get to the Completing Installation part I wait a little and suddenly I get a red error box and it says something about "Windows cannot be installed..." and then pc shuts down. The error box is there for like 0.5 seconds so...
Installation & Setup


Our Sites

Site Links

About Us

Find Us

Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

Designer Media Ltd

All times are GMT -5. The time now is 23:43.

Twitter Facebook Google+



Windows 7 Forums

Seven Forums Android App Seven Forums IOS App