BSOD on a fresh install (win7 pro 64 bit)


  1. Posts : 1
    Win7 Pro 64-bit
       #1

    BSOD on a fresh install (win7 pro 64 bit)


    I am getting plagued by BSoDs on a fresh (installed yesterday) install of windows 7 pro 64-bit.

    This is the second time that windows 7 was installed on this system. The first was also plagued by BSoDs

    any help would be greatly appreciated



    Is Windows 7 . . .
    - x86 (32-bit) or x64 ? 64 bit
    - the original installed OS on the system? Custom built system
    - an OEM or full retail version? retail version obtained from college IT dept
    - OEM = came pre-installed on system
    - Full Retail = you purchased it from retailer

    - What is the age of system (hardware)? pretty new, built the system in march
    - What is the age of OS installation (have you re-installed the OS?) installed OS on 4/17/12




    Custom built system

    Operating System
    MS Windows 7 64-bit SP1

    CPU
    AMD Phenom II X4 960T 28 °C
    Thuban 45nm Technology

    RAM
    CORSAIR Vengeance CMZ8GX3M2A1600C9B
    8.00 GB Dual-Channel DDR3 @ 899MHz (9-12-12-30)

    Motherboard
    MSI 970A-G45 (MS-7693) (CPU 1) 36 °C

    Graphics
    M220VA (1920x1080@60Hz)
    1024MB GeForce GTX 550 Ti (EVGA) 38 °C

    Hard Drives
    488GB Seagate ST3500320AS ATA Device (SATA) 26 °C
    488GB Seagate ST3500630AS ATA Device (SATA) 32 °C

    Optical Drives
    ASUS BC-12B1ST ATA Device
      My Computer


  2. Posts : 28,845
    Win 8 Release candidate 8400
       #2


    These crashes were caused by memory corruption/exception (Cx05) probably a driver.
    Please run these two tests to verify your memory and find which driver is causing the problem.


    * If you are overclocking anything reset to default before running these tests.
    In other words STOP!!!

    * If you have a Raid update its Driver.




    Memtest.
    *Download a copy of Memtest86 and burn the ISO to a CD using Iso Recorder or another ISO burning program. Memtest86+ - Advanced Memory Diagnostic Tool

    *Boot from the CD, and leave it running for at least 5-7 passes.

    Just remember, any time Memtest reports errors, it can be either bad RAM or a bad motherboard slot.

    Test the sticks individually, and if you find a good one, test it in all slots.

    Any errors are indicative of a memory problem.

    If a known good stick fails in a motherboard slot it is probably the slot.


    RAM - Test with Memtest86+






    Driver Verifer

    Using Driver Verifier is an iffy proposition.
    Most times it'll crash and it'll tell you what the driver is.
    But sometimes it'll crash and won't tell you the driver.
    Other times it'll crash before you can log in to Windows.
    If you can't get to Safe Mode, then you'll have to resort to offline editing of the registry to disable Driver Verifier.

    I'd suggest that you first backup your stuff and then make sure you've got access to another computer so you can contact us if problems arise.
    Then make a System Restore point (so you can restore the system using the Vista/Win7 Startup Repair feature).

    In Windows 7 you can make a Startup Repair disk by going to Start....All Programs...Maintenance...Create a System Repair Disc - with Windows Vista you'll have to use your installation disk or the "Repair your computer" option at the top of the Safe Mode menu .

    Then, here's the procedure:
    - Go to Start and type in "verifier" (without the quotes) and press Enter
    - Select "Create custom settings (for code developers)" and click "Next"
    - Select "Select individual settings from a full list" and click "Next"
    - Select everything EXCEPT FOR "Low Resource Simulation" and click "Next"
    NOTE: You can use Low Resource Simulation if you'd like.
    From my limited experimentation it makes the BSOD's come faster.
    - Select "Select driver names from a list" and click "Next"
    Then select all drivers NOT provided by Microsoft and click "Next"
    - Select "Finish" on the next page.

    If you are using win 8 add these

    - Concurrency Stress Test
    - DDI compliance checking

    Reboot the system and wait for it to crash to the Blue Screen.
    Continue to use your system normally, and if you know what causes the crash, do that repeatedly.
    The objective here is to get the system to crash because Driver Verifier is stressing the drivers out.
    If it doesn't crash for you, then let it run for at least 36 hours of continuous operation (an estimate on my part).

    Reboot into Windows (after the crash) and turn off Driver Verifier by going back in and selecting "Delete existing settings" on the first page, then locate and zip up the memory dump file and upload it with your next post.


    If you can't get into Windows because it crashes too soon, try it in Safe Mode.
    If you can't get into Safe Mode, try using System Restore from your installation DVD to set the system back to the previous restore point that you created.

    Thanks to JGriff2 & Usasma.
    Using Driver Verifier to identify issues with Windows drivers for advanced users

    Driver Verifier

    Using Driver Verifier (Windows Drivers)



    Avast can be a contributing cause of BSOD'S . Please remove and replace with Microsoft Security Essentials AT LEAST TO TEST


    http://files.avast.com/files/eng/aswclear5.exe

    Microsoft Security Essentials - Free Antivirus for Windows
      My Computer


 

  Related Discussions
Our Sites
Site Links
About Us
Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

© Designer Media Ltd
All times are GMT -5. The time now is 00:21.
Find Us