Windows 7: Different BSOD every time I turn on computer

Please help. Every time I turn on computer I receive a different BSOD. I can't even give my computer info because I haven't been able to stay on it long enough. The following are the BSOD that I just received in the last hour.
IRQL_NOT_LESS_OR_EQUAL
PAGE_FAULT_IN_NONPAGED_AREA
BAD_POOL_HEADER
MEMORY_MANAGEMENT
I has also started with Windows Error Recovey which I have done but that has froze on me or hasn't helped. I have also reset computer to its original state. Now as soon as I turn on it goes to a BSOD almost immediately. I know you need more info about computer, so if you can tell me what info it is you need, I will get it. I can tell you that it is a desktop.

Did you build the system, or did you buy it built by a vendor (HP, Dell, etc.)?

Is the system still under warranty?

I bought it. Its an HP. I didn't buy a warranty. Also, yesterday I reset the OS. I was told by emachines support to press the ALT. and the F10 button at the same time at start up. Everything seemed to be ok until right now. It has been freezing up on me. Please help.

Writhziden-My computer just froze on the startup repair.

Yesterday, under the advice of emachines support, I reset my OS. I was told to press ALT and F10 at the same time at start up. Everything was okay for the day, until today. Now, it has been freezing up on me and I did receive one BSOD. I have attached dump file and system health report per your tutorial instructions. Also, I am including my system specs.

System Manufacturer/Model Number HP Pavilion e9110t
OS Windows 7 Home Premium 64 Bit
CPU Intel(R) Core(TM)2 Quad CPU Q9550 @ 2.83GHz
Motherboard Pegatron IPIEL-LA3
Memory 6.00 GB Hundai HMT125U6BFR8C-H9
Graphics Card ATI Radeon HD 4850
Sound Card Realtek High Definition Audio/ATI High Definition Audio
Monitor(s) Displays Acer AL2216W
Screen Resolution 1680x1050
Keyboard HP Keyboard
Mouse HP Mouse
PSU Unknown/installed by HP
Case HP generic case
Cooling Intel Stock Cooling
Hard Drives Hitachi HDP725050GLA360 ATA Device 500 GB
Internet Speed Download: 19.15 Mbps Upload: 1.67 Mbps
Other Info Network Adapter Realtek RTL8168D/8111D Family PCI-E Gigabit Ethernet NIC (NDIS 6.20) Network Adapter 802.11n Wireless PCI Express Card LAN Adapter cs.

Attachment 216299

Attachment 216300

Can you please explain all the troubleshooting steps you have already done and be as specific as possible about what the steps were and what the results were?

I am a little confused as to the current status of the system. You say you did a factory recovery, then it started freezing on startup? Is that correct?

You said after the factory recovery the system worked fine. Then it started freezing? What software/hardware changes did you make between when the system worked fine and when it started freezing?

Can you start in Safe Mode?

Advanced Boot Options

-> Safe Mode



Ah, you did not tell me you started a thread with the info... Your one crash indicates the graphics card or its drivers. Make sure the card is not clogged with dust. I have the same system as you, and mine gets a lot of dust buildup that causes overheating of components:

To remove dust, follow the subsequent general procedure. If you have a desktop bought from Dell, HP, Sony, Lenovo, etc. make sure removing the desktop casing will not void your warranty first. Call the company if you are still under warranty and ask if it is okay to remove the casing and blow dust out. The procedure described is fine for laptops; just make sure no stickers are on panels saying if you remove the panel it will void the warranty.

1. Shut down and turn off your computer.
2. Unplug all power supplies to the computer (AC Power then battery for laptops, AC power for desktops)
3. Hold down the power button for 30 seconds to close the circuit and ensure all power drains from components.
4. Remove the casing for a desktop, or remove any screwed on panels and disc drives for laptops.
5. Blow out the dust inside by using a can of compressed air or a low pressure compressor. You will want to put the computer on a desk or table so you can maintain the can in an upright position if using a can of air. Blow into all crevices on the motherboard, heat sinks, cards, modules, etc. for a desktop. Blow into vents, opened panels, disc drive areas, USB ports, and the keyboard if it is a laptop. You may also want to blow inside the disc drive by replacing the drive to the laptop, starting the computer, opening the drive, and then turning off the computer and removing all power as described above including the 30 second power button step. For a desktop, you may also want to blow inside the disc drive by starting the computer, opening the drive, and then turning off the computer and removing all power as described above including the 30 second power button step.
6. Replace casing for the desktop. Replace panels and disc drive (if you have not already done so) for the laptop.
7. Plug power supplies in. AC adapter for the desktop. Battery and then AC Adapter for the laptop.
8. Start the computer and see if performance is better.

Sorry about starting another thread this is new to me.
So you're saying that it just might be a dusty computer?

Quite possible. When's the last time you blew the dust out? It should be done once every few months and at least once every six months.

To be honest with you, I have never done that before. I will do it as soon as possible. But first you suggest I contact the manufacturer? I have another question, I read somewhere that you should touch the outside case before you start working to discharge your body static. Is that correct?

I usually recommend grabbing metal inside the case, such as a hard disk bay.

If you are under warranty, you should contact HP. Do you have an extended warranty?