Windows 7 Forums

Welcome to Windows 7 Forums. Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks.


Windows 7: Excessive BSODing with volmgr.sys and other error messages

26 Jun 2012   #21
Ortizme

Windows 7 64 bit
 
 

Here are the performance reports.


My System SpecsSystem Spec
.
26 Jun 2012   #22
writhziden

Windows 7 Home Premium 64 Bit
 
 

Your recent image was broken.

As for your hard disk suspect: yes, that could cause the issues you have had. Here are my usual steps for hard disk related issues:
Quote   Quote: Originally Posted by writhziden
  • If you are overclocking any hardware, please stop.

  • Run Disk Check with both boxes checked for all HDDs and with Automatically fix file system errors checked for all SSDs. Post back your logs for the checks after finding them using Check Disk (chkdsk) - Read Event Viewer Log (you may need to search for wininit instead of chkdsk).
    For any drives that do not give the message:
    Windows has checked the file system and found no problems
    run disk check again as above. In other words, if it says:
    Windows has made corrections to the file system
    after running the disk check, run the disk check again.

  • Run all Basic tests with SeaTools: S.M.A.R.T. Check, Short Drive Self Test, Drive Information, Short Generic, and Long Generic. Run the tests for all HDDs.
    SeaTools for Windows

    SeaTools for DOS
  • If you have an SSD, make sure the following are up to date:
    • SSD firmware
    • BIOS Version
    • Chipset Drivers
    • Hard disk controller drivers/SATA drivers
    • If you have a Marvell IDE ATA/ATAPI device, make sure the drivers are up to date from the Intel site or Marvell site and not from your motherboard/vendor support site.

  • Check Windows for corruption. Run SFC /SCANNOW Command - System File Checker up to three times to fix all errors with a restart in between each. Post back if it continues to show errors after a fourth run or if the first run comes back with no integrity violations. Use OPTION THREE of SFC /SCANNOW Command - System File Checker to provide us with the sfcdetails.txt file if errors occur.

  • Download and install Malwarebytes, update it, do not start the free trial, and then run a full scan. Also run a full scan with your antivirus software installed on your system. If you do not have antivirus software installed, see the Good and Free system security combination. for better security steps and scanning tools. Make sure to update the security software before running the full scan.

  • Run the boot version of Memtest86+ paying close attention to Parts 2 and 3 of the tutorial. Also, in case Memtest86+ misses anything and comes up with no errors, run the extended version of the Windows Memory Diagnostics Tool for at least five passes. These you may want to run overnight since they take a long time to complete (run them an hour before bed each of the next two nights and check before going to sleep that they are still running).
    warning   Warning
    Before you proceed with the following, answer these two questions: Are you still under warranty? Does your warranty allow you to open up the machine to check hardware? If you are unsure of the answers to these questions, contact your system manufacturer. WARNING: The steps that follow can void your warranty!!!

    For Part 3: If You Have Errors: If you swap any memory components, follow these steps for ESD safety:
    1. Shut down and turn off your computer.
    2. Unplug all power supplies to the computer (AC Power then battery for laptops, AC power for desktops)
    3. Hold down the power button for 30 seconds to close the circuit and ensure all power drains from components.
    4. Make sure you are grounded by using proper grounding techniques, i.e. work on an anti-static workbench, anti-static desk, or an anti-static pad. Hold something metallic while touching it to the anti-static surface, or use an anti-static wristband to attach to the anti-static material while working. If you do not have an anti-static workbench, desk, or pad, you can use your computer tower/case by finding a metal hold in it, such as a drive bay.
    Once these steps have been followed, it is safe to remove and replace components within your computer.
My System SpecsSystem Spec
27 Jun 2012   #23
Ortizme

Windows 7 64 bit
 
 

I did most of those things and fixed the problems they presented.

Today I discovered my HDD's sata cable was plugged into the sata 2 port and not the 3 port. I fixed it and things appear to be improving.

I can't open steam to test if my games will run so I'll keep you updated.
My System SpecsSystem Spec
.

Reply

 Excessive BSODing with volmgr.sys and other error messages




Thread Tools Search this Thread
Search this Thread:

Advanced Search




Similar help and support threads
Thread Forum
BSOD after excessive chrome use?not sure error 0x0000003b
My laptop (HP Pavilion dv6 6153cl) went down a couple times now First time it happened: I had quite a few tabs on chrome open, and was using word doc while streaming a world cup game live. The screen suddenly went black, then nothing worked, so I had to force a shut down From then on, the...
BSOD Help and Support
BSOD volmgr.sys, error 0x000000C9
Hi all, Attached is the SF zipped folder. I have been experiencing BSODs. I am currently running on Windows 7 Professional, 32-bit. Any other relevant information I will be gladly able to provide, let me know. Kindly assist. Thank you all in advance.
BSOD Help and Support
How many error messages do you get each day?
I would find it interesting to see how many error messages show up in your event viewer, on average, each day. I can get a lot when I am installing/configuring new hardware or software, and most of my error messages get generated on each start-up. On average when things are running reasonably...
General Discussion
three error messages
Hi Guys, I'm a bit stumped, being to trying to find a solution on the net to no arrival. None of the inbuilt windows fixers have been very helpful. Error messages when updating are; - 80070570 - 570 - 80070130 Frustrating as this computer is only 2 weeks old.
Windows Updates & Activation
Installation Never Starts: Something about volmgr.sys
Hello! This may not be enough information to get help, unfortunately for me to get the complete error message I need to take apart this computer a bit and it's generally a bit of a hassle. I hope to get at least a hint of how to fix it with what I have before I do that. I have a fresh system....
Installation & Setup
MDT Volmgr.sys error with Win7 x32
I'm working on building a 32-bit Win7 image. For some reason it keeps giving us issues. We've been capturing it on a Win7 box, but once we move it to the server, it won't put the image down properly. (Note that the Win7 box used to capture doesn't have issues putting the image down, which is...
BSOD Help and Support


Our Sites

Site Links

About Us

Find Us

Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

Designer Media Ltd

All times are GMT -5. The time now is 22:52.

Twitter Facebook Google+



Windows 7 Forums

Seven Forums Android App Seven Forums IOS App