BSOD STOP: 0x00000124 Randomly on 2mins tops if even that

Page 1 of 2 12 LastLast

  1. Posts : 34
    windows 7 professional x64
       #1

    BSOD STOP: 0x00000124 Randomly on 2mins tops if even that


    Hello

    "BSOD STOP: 0x00000124 Randomly on 2mins tops if even that"
    With that said

    Here is how it all started, i was watching TV last night and had the computer on idle next to me. It suddenly rebooted and i was like wth? then at windows start up it BSOD:ed me the 0x0..124
    and now it won't stop, can't find the reason it doesn't matter if i press repair, start from last known ... neither can i hold it on for longer then 1-2mins "if im lucky" before it goes BSOD.

    I can enter bios without any problems i've even kept bios running for 5-10mins without and changes as soon as i enter windows in any form "even safe modes" it BS:s on me.
    I've tried to drop down the auto clock even setting it all to power saving still BS on me.
    I have checked all the tempetures and nothing seem to be overheating ?

    When i got the chance i copy all the dump files in the folder minidump and they can be found here http://sdrv.ms/Mfp2aL

    I'll sshot the BSOD and upload it too in few mins
    Any help would be helpful

    I'm sorry for my bad english i hope it is understandable.

    Thanks in advance
      My Computer


  2. Posts : 11,269
    Windows 7 Home Premium 64 Bit
       #2

    BSOD Posting Instructions
    We really could use the full crash reports if you can get them through Safe Mode :


    Analysis:
    Some of your older crashes point to the Marvell controller drivers. Try removing the software through Start Menu -> Control Panel -> Uninstall a program if possible. Uninstall and Remove Software in Safe Mode may also help.
      My Computer


  3. Posts : 34
    windows 7 professional x64
    Thread Starter
       #3

    Here is a picture and i'm atm loading up video to youtube so you will see the whole process.
      My Computer


  4. Posts : 34
    windows 7 professional x64
    Thread Starter
       #4

    writhziden said:
    BSOD Posting Instructions
    We really could use the full crash reports if you can get them through Safe Mode :
    Analysis:
    Some of your older crashes point to the Marvell controller drivers. Try removing the software through Start Menu -> Control Panel -> Uninstall a program if possible. Uninstall and Remove Software in Safe Mode may also help.
    There was 2 marvell drivers.. got the chance to remove one .. but dídnt get the chance to remove the second.. and now it BS on as soon as log in "even safe mode"
    Gonna try wait few mins and try again.
    And full report seem not possible for me since it BS pretty quick as you see here on the first part of the video and that goes for all safe mode with and without network

    Last edited by thugishangel; 11 Jul 2012 at 07:39.
      My Computer


  5. Posts : 11,269
    Windows 7 Home Premium 64 Bit
       #5

    BugCheck 0x124:

    System Restore:
    Since this just started happening, I would suggest trying a system restore to before it started. Do the following steps:
      My Computer


  6. Posts : 34
    windows 7 professional x64
    Thread Starter
       #6

    writhziden said:
    BugCheck 0x124:
    System Restore:

    Since this just started happening, I would suggest trying a system restore to before it started. Do the following steps:
    I'm going to try this...though i need to get hang of a system repair disc
      My Computer


  7. Posts : 11,269
    Windows 7 Home Premium 64 Bit
       #7
      My Computer


  8. Posts : 34
    windows 7 professional x64
    Thread Starter
       #8

    Here is two more videos that shows abit more when error occur





    about 5sec after i turn off on the part 3 it bsod again.






    How do i know if it is a hardware issue or not... because this seem to happen when i only do something with or in windows 7?
    When i check the temps both in bios and in win 7 "when i get in and get the luck to see" the temps are more or less 30C on cpu and i've tryed to have my graph card on full throttle 100% and even without full power on the fans it still is cool. I know on the part 2 video looks like when i turn it of and it bsod but that was just bad timing.
      My Computer


  9. Posts : 34
    windows 7 professional x64
    Thread Starter
       #9

    Without System Repair Disc




    Part is without the repair disc, i hope it looks different when i try the same with the repair disc?

    ** BTW When i look on the minidump files copied to my other computer, it tells me:
      My Computer


  10. Posts : 11,269
    Windows 7 Home Premium 64 Bit
       #10

    Failure to Boot:
    Even though you are not having a failure to boot, the steps for Troubleshooting Windows 7 Failure to Boot may be helpful.


    Hardware Stripdown:
    I have a feeling your problems are the result of a damaged Windows install, but you could still see if there is a failed hardware component.

       Warning
    Before you proceed with the following, answer these two questions: Are you still under warranty? Does your warranty allow you to open up the machine to check hardware? If you are unsure of the answers to these questions, contact your system manufacturer. WARNING: The steps that follow can void your warranty!!!


    Strip down your system to run only the bare essentials: one RAM module, the CPU, motherboard, one hard disk, one graphics card (or use onboard graphics if you have it), keyboard, mouse, and one monitor. See how the system behaves by running Windows for twice as long as it typically takes for you to get a crash. If it is stable, add one piece of hardware back at a time until you get crashes again. Take notes of what hardware you add and how the system responds to the hardware changes.

    As you add and remove hardware, follow these steps for ESD safety:
    1. Shut down and turn off your computer.
    2. Unplug all power supplies to the computer (AC Power then battery for laptops, AC power for desktops)
    3. Hold down the power button for 30 seconds to close the circuit and ensure all power drains from components.
    4. Make sure you are grounded by using proper grounding techniques, i.e. work on an anti-static workbench, anti-static desk, or an anti-static pad. Hold something metallic while touching it to the anti-static surface, or use an anti-static wristband to attach to the anti-static material while working. If you do not have an anti-static workbench, desk, or pad, you can use your computer tower/case by finding a metal hold in it, such as a drive bay.

    Once these steps have been followed, it is safe to remove and replace components within your computer.
      My Computer


 
Page 1 of 2 12 LastLast

  Related Discussions
Our Sites
Site Links
About Us
Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

© Designer Media Ltd
All times are GMT -5. The time now is 14:01.
Find Us