avgldx64.sys Thu Oct 6 22:55:41 2011 (4E8E783D)
Looks like you are using AVG Anti-Virus. Please create a System Restore point, and uninstall it. Then install Microsoft Security Essentials - Free Antivirus for Windows
for trouble shooting purposes.
AODDriver4.1 ROOT\LEGACY_AODDRIVER4.1\0000 This device is not present, is not working properly, or does not have all its drivers installed.
Please use this site to solve this problem: Rage3D Discussion Area - View Single Post - The AODDriver4.1 service failed .... Cat 12.2 megaproblems
Start Menu\Programs\Driver Fusion Public:Start Menu\Programs\Driver Fusion Public
Please remove Driver Fusion as it trying to remove system drivers could cause problems. Analysis
SaiK0728.sys Fri Jan 18 12:28:04 2008 (4790EFB4)
SaiMini.sys Fri Jan 18 12:28:16 2008 (4790EFC0)
SaiBus.sys Fri Jan 18 12:28:24 2008 (4790EFC8)
Any drivers before 2009 are known to cause problems. Please update those: Download Saitek Drivers and Software | Saitek.com
Probably caused by : memory_corruption ( nt!MiDeletePteRun+d8 )
Invalid system memory was referenced. This cannot be protected by try-except,
it must be protected by a Probe. Typically the address is just plain bad or it
is pointing at freed memory.
Shows you are having some possible memory problems. Please run a RAM - Test with Memtest86+
Probably caused by : Pool_Corruption ( nt!ExDeferredFreePool+249 )
This can be cause by general hardware or software. So to knock out the possibilty of hardware, please do the following steps:
Before you proceed with the following, answer these two questions: Are you still under warranty? Does your warranty allow you to open up the machine to check hardware?
If you are unsure of the answers to these questions, contact your system manufacturer. WARNING: The steps that follow can void your warranty!!!
For your hardware stop 0x124 crash, read through Stop 0x124 - what it means and what to try and use the following hardware checks to supplement that link.
- If you are overclocking any hardware, please stop.
- If you have an SSD, make sure the following are up to date:
- SSD firmware
- BIOS Version
- Chipset Drivers
- Hard disk controller drivers/SATA drivers
- If you have a Marvell IDE ATA/ATAPI device, make sure the drivers are up to date from the Intel site or Marvell site and not from your motherboard/vendor support site.
- Run all but the advanced tests with SeaTools for HDDs.
SeaTools for Windows
SeaTools for DOS
- Monitor temperatures during the following tests.
Use the following programs to monitor the temperatures.
- Run the boot version of Memtest86+ paying close attention to Parts 2 and 3 of the tutorial. Also, in case Memtest86+ misses anything and comes up with no errors, run the extended version of the Windows Memory Diagnostics Tool for at least five passes. These you may want to run overnight since they take a long time to complete (run them an hour before bed each of the next two nights and check before going to sleep that they are still running).
For Part 3: If You Have Errors: If you swap any memory components, follow these steps for ESD safety:
Once these steps have been followed, it is safe to remove and replace components within your computer.
- Shut down and turn off your computer.
- Unplug all power supplies to the computer (AC Power then battery for laptops, AC power for desktops)
- Hold down the power button for 30 seconds to close the circuit and ensure all power drains from components.
- Make sure you are grounded by using proper grounding techniques, i.e. work on an anti-static workbench, anti-static desk, or an anti-static pad. Hold something metallic while touching it to the anti-static surface, or use an anti-static wristband to attach to the anti-static material while working. If you do not have an anti-static workbench, desk, or pad, you can use your computer tower/case by finding a metal hold in it, such as a drive bay.
Coutesy of: writhziden
After you follow these steps please post back with results.