Windows 7 Forums
Welcome to Windows 7 Forums. Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks.


Windows 7: BSOD while shutting down pc, BCCode: 1e (SF Diag tool files attached)


27 Jul 2012   #11

Windows 8.1 Pro x64
 
 

Well if you have anymore crashes post up the latest crash files, so we can do better.

-Justin


My System SpecsSystem Spec
.

27 Jul 2012   #12

Windows 7 ultimate x64 Build 6_1_7601
 
 

Well i will run the 3d mark dx11. I have done it couple of times in past with this pc, so if it runs without problems i should be fine?
My System SpecsSystem Spec
27 Jul 2012   #13

Windows 7 ultimate x64 Build 6_1_7601
 
 

Score
P5311 3DMarks
Graphics Score
5533
Physics Score
4766
Combined Score
4707
PC Health Check

Your PC is performing properly.

D: is this reliable?
My System SpecsSystem Spec
.


27 Jul 2012   #14

Windows 8.1 Pro x64
 
 

That only tests the DirectX stuff(yes stuff) lol.

Follow these trouble shooting instructions:

Quote:
BugCheck 0x124


warning   Warning
Before you proceed with the following, answer these two questions: Are you still under warranty? Does your warranty allow you to open up the machine to check hardware? If you are unsure of the answers to these questions, contact your system manufacturer. WARNING: The steps that follow can void your warranty!!!

For your hardware stop 0x124 crash, read through Stop 0x124 - what it means and what to try and use the following hardware checks to supplement that link.
  • If you are overclocking any hardware, please stop.

  • If you have an SSD, make sure the following are up to date:
    • SSD firmware
    • BIOS Version
    • Chipset Drivers
    • Hard disk controller drivers/SATA drivers
    • If you have a Marvell IDE ATA/ATAPI device, make sure the drivers are up to date from the Intel site or Marvell site and not from your motherboard/vendor support site.

  • Run all but the advanced tests with SeaTools for HDDs.
    SeaTools for Windows

    SeaTools for DOS
  • Monitor temperatures during the following tests.
    Use the following programs to monitor the temperatures.
  • Run the boot version of Memtest86+ paying close attention to Parts 2 and 3 of the tutorial. Also, in case Memtest86+ misses anything and comes up with no errors, run the extended version of the Windows Memory Diagnostics Tool for at least five passes. These you may want to run overnight since they take a long time to complete (run them an hour before bed each of the next two nights and check before going to sleep that they are still running).

    For Part 3: If You Have Errors: If you swap any memory components, follow these steps for ESD safety:
    1. Shut down and turn off your computer.
    2. Unplug all power supplies to the computer (AC Power then battery for laptops, AC power for desktops)
    3. Hold down the power button for 30 seconds to close the circuit and ensure all power drains from components.
    4. Make sure you are grounded by using proper grounding techniques, i.e. work on an anti-static workbench, anti-static desk, or an anti-static pad. Hold something metallic while touching it to the anti-static surface, or use an anti-static wristband to attach to the anti-static material while working. If you do not have an anti-static workbench, desk, or pad, you can use your computer tower/case by finding a metal hold in it, such as a drive bay.
    Once these steps have been followed, it is safe to remove and replace components within your computer.

Coutesy of: writhziden
My System SpecsSystem Spec
27 Jul 2012   #15

Windows 7 ultimate x64 Build 6_1_7601
 
 

Quote   Quote: Originally Posted by HonorGamer View Post
That only tests the DirectX stuff(yes stuff) lol.

Follow these trouble shooting instructions:

Quote:
BugCheck 0x124


warning   Warning
Before you proceed with the following, answer these two questions: Are you still under warranty? Does your warranty allow you to open up the machine to check hardware? If you are unsure of the answers to these questions, contact your system manufacturer. WARNING: The steps that follow can void your warranty!!!

For your hardware stop 0x124 crash, read through Stop 0x124 - what it means and what to try and use the following hardware checks to supplement that link.
  • If you are overclocking any hardware, please stop.

  • If you have an SSD, make sure the following are up to date:
    • SSD firmware
    • BIOS Version
    • Chipset Drivers
    • Hard disk controller drivers/SATA drivers
    • If you have a Marvell IDE ATA/ATAPI device, make sure the drivers are up to date from the Intel site or Marvell site and not from your motherboard/vendor support site.

  • Run all but the advanced tests with SeaTools for HDDs.
    SeaTools for Windows

    SeaTools for DOS
  • Monitor temperatures during the following tests.
    Use the following programs to monitor the temperatures.
  • Run the boot version of Memtest86+ paying close attention to Parts 2 and 3 of the tutorial. Also, in case Memtest86+ misses anything and comes up with no errors, run the extended version of the Windows Memory Diagnostics Tool for at least five passes. These you may want to run overnight since they take a long time to complete (run them an hour before bed each of the next two nights and check before going to sleep that they are still running).

    For Part 3: If You Have Errors: If you swap any memory components, follow these steps for ESD safety:
    1. Shut down and turn off your computer.
    2. Unplug all power supplies to the computer (AC Power then battery for laptops, AC power for desktops)
    3. Hold down the power button for 30 seconds to close the circuit and ensure all power drains from components.
    4. Make sure you are grounded by using proper grounding techniques, i.e. work on an anti-static workbench, anti-static desk, or an anti-static pad. Hold something metallic while touching it to the anti-static surface, or use an anti-static wristband to attach to the anti-static material while working. If you do not have an anti-static workbench, desk, or pad, you can use your computer tower/case by finding a metal hold in it, such as a drive bay.
    Once these steps have been followed, it is safe to remove and replace components within your computer.

Coutesy of: writhziden
I will follow these steps.

I know it does test DirectX stuff only, even so i was just trying to point out if that does mean my gpu should be ok?

Im also considering to reinstall my win 7 cuz all these problems started after i installed some custom themes and used the beta drivers and free registry cleaner. D:
My System SpecsSystem Spec
27 Jul 2012   #16

Windows 8.1 Pro x64
 
 

Your GPU should be okay, but like i said follow the testing steps and post the results.

lets wait on re-installing as a last choice. Lets try to save it first :P

-Justin
My System SpecsSystem Spec
27 Jul 2012   #17

Windows 7 ultimate x64 Build 6_1_7601
 
 

Quote   Quote: Originally Posted by HonorGamer View Post
Your GPU should be okay, but like i said follow the testing steps and post the results.

lets wait on re-installing as a last choice. Lets try to save it first :P

-Justin
kk :3 i want to say that i really apreciate your patience.
My System SpecsSystem Spec
27 Jul 2012   #18

Windows 8.1 Pro x64
 
 

It takes patience to solve a problem. Especially with computers :P.

-Justin
My System SpecsSystem Spec
27 Jul 2012   #19

Windows 7 ultimate x64 Build 6_1_7601
 
 

Quote   Quote: Originally Posted by HonorGamer View Post
It takes patience to solve a problem. Especially with computers :P.

-Justin
haha yea! btw is my ssd safe to test with seatools? Im currently testing my hdds only with it.
My System SpecsSystem Spec
27 Jul 2012   #20

Windows 8.1 Pro x64
 
 

Yes, it is safe. The only thing you need to avoid is using the Disk Defrag.
My System SpecsSystem Spec
Reply

 BSOD while shutting down pc, BCCode: 1e (SF Diag tool files attached)




Thread Tools



Similar help and support threads for2: BSOD while shutting down pc, BCCode: 1e (SF Diag tool files attached)
Thread Forum
BSOD while playing D3, got that zipped folder from the SF diag tool. BSOD Help and Support
BSOD playing any game SF Diag Tool Inside BSOD Help and Support
Solved BSOD, likely related to memory corruption; SF Diag dump file attached BSOD Help and Support
Solved BSOD - BCcode d1, system health report and NT6_BSOD files attached BSOD Help and Support
BSOD Bccode 1a dump files attached BSOD Help and Support
BSOD Bad Header Pool - SF DIag Tool dump BSOD Help and Support
Help w. BSOD - SF Diag dmp files attached BSOD Help and Support

Our Sites

Site Links

About Us

Find Us

Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

Designer Media Ltd

All times are GMT -5. The time now is 08:38 PM.
Twitter Facebook Google+



Windows 7 Forums

Seven Forums Android App Seven Forums IOS App
  

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33