New
#11
ok I ran did the offline full system scan and it didn't find anything
ok I ran did the offline full system scan and it didn't find anything
it froze again and when it does it's a whole system freeze I can't alt f4 or ctrl alt dlt or anything like that. Just thought that might help you.
Last edited by tatertot74121; 03 Aug 2012 at 14:45. Reason: it was a repost
did you follow the other advice about keeping the cover off, blowing a fan on it, using Speccy to monitor temps?
Run the enclosed script. Attach the resulting wdologs.zip file to your next post.
Incidentally, I disagree 100% with your assessment regarding the power supply not being at fault.
# **********************INSTRUCTIONS**************************
# STEP 1 ** RUN POWERSHELL AS ADMINISTRATOR ******************
# ************************************************************
#
# WIN key | type POWERSHELL | do NOT hit ENTER |
# in the PROGRAMS list, right-click on WINDOWS POWERSHELL |
# choose "Run as administrator" |
# Click on the YES button (if such appears)
#
# WIN key = key with Microsoft log on top
#
# for the guru:
# WIN | type POWERSHELL | CTRL+SHIFT+ENTER key combo | ALT+Y keycombo
# ************************************************************
# STEP 2 ** COPY AND PASTE ***********************************
# ************************************************************
#
# COPY the script using CTRL+C,
# COPY every line of script down thru both EXIT statements
#
# PASTE into Powershell
#----Right-Click at the PowerShell Prompt
#----(Ctrl+V does not work)
#
# Start copying with first script line without a # at start of the line
# Note: Actually, you can paste the entire file if you rather
#-------Lines starting with a # are ignored by PowerShell
# ************************************************************
# STEP 3 ** SCRIPT OUTPUT & SCRIPT PURPOSE *******************
# ************************************************************
# --The script output and purpose is given at the very front of the script
#
# --The script output and purpose is given at the very front of the script
#
# ************************************************************
# ***************** NOTE - POWERSHELL VERSION*****************
# if you receive this error msg:
#--The system can not find the path specified
# you may need to update your PowerShell
# you must be using Powershell 2.0 or later.
#
# To determine your Powershell version:
#---Run PowerShell
#---enter $host.version
#---you should see at least:
# Major Minor Build Revision
# ----- ----- ----- --------
# 2......0......-1.....-1
#
# If you do not see the above, update your Vista/Win 7.
# ************************************************************
# *************** NOTE - EXECUTION POLICY*********************
# If you haven't set the execution policy, you may need to:
#---Run PowerShell
#---enter SET-EXECUTIONPOLICY -EXECUTIONPOLICY REMOTESIGNED
# ************************************************************
Script:
# ************************************************************
# Zips up your log files from Windows Defender Offline
# and extended info about the log files
# Places WDOlogs.ZIP on your Desktop
#
# ************************************************************
function New-Zip {
param([Parameter(Mandatory=$true, Position=0, ValueFromPipeline=$true)]
[String] $Path, [Switch] $PassThru, [Switch] $Force )
Process { if (Test-Path $path) {if (-not $Force) { return } }
Set-Content $path ("PK" + [char]5 + [char]6 + ("$([char]0)" * 18))
$item = Get-Item $path; $item.IsReadOnly = $false;if ($passThru) { $item } } }
function Copy-ToZip {param(
[Parameter(Mandatory=$true,Position=0,ValueFromPipelineByPropertyName=$true)] [Alias('FullName')]
[String]$File, [Parameter(Mandatory=$true,Position=1)] [String]$ZipFile,[Switch]$HideProgress,[Switch]$Force )
Begin {$ShellApplication = New-Object -ComObject Shell.Application
if (-not (Test-Path $ZipFile)) {New-Zip $ZipFile};$Path = Resolve-Path $ZipFile
$ZipPackage =$ShellApplication.Namespace("$Path")}
Process {$RealFile = Get-Item $File; if (-not $RealFile) { return }
if (-not $hideProgress) {$perc +=5; if ($perc -gt 100) { $perc = 0 }
Write-Progress "Copying to $ZipFile" $RealFile.FullName -PercentComplete $perc}
$Flags = 0; if ($force) {$flags = 16 -bor 1024 -bor 64 -bor 512};Write-Verbose $realFile.Fullname
$ZipPackage.CopyHere($realFile.Fullname, $flags);Start-Sleep -Milliseconds 500}}
$divider = "#" * 79
$fileinfo = join-path $env:TEMP \wdofileinfo.txt
IF (test-path $fileinfo) {del $fileinfo -ea:silentlycontinue -force:$true}
$dir = $env:windir + '\Microsoft Antimalware\Support'
$a = dir $dir -rec -force -ea:silentlycontinue | sort-object -property lastwritetime
$b = $a | where {$_.extension -eq '.log'} |Select mode, fullname, name, creationtime, lastwritetime, lastaccesstime, length, extension
$b | out-file -append $fileinfo
$b | foreach ($_.fullname) {
out-file -append $fileinfo -inputobject $divider
out-file -append $fileinfo -inputobject $_.fullname;
out-file -append $fileinfo -inputobject (get-content -path $_.fullname)
}
$ziploc = $env:userprofile + '\desktop\WDOlogs.ZIP'
new-zip $ziploc -verbose:$false -ea:silentlycontinue -force:$true
copy-tozip $fileinfo $ziploc -verbose:$false -hideprogress:$true
del $fileinfo
EXIT
EXIT
# ************************************************************
Yes I did but it still froze afterwards. And I'm not sure because I got it last summer and it hasn't ever froze before now
Last edited by tatertot74121; 04 Aug 2012 at 13:23. Reason: I forgot to add the rest
ok sorry about that, there's the zip file
Have you implemented the suggestions in post #9?
=========================================================
Carry out following procedure:
MEMORY DUMPS - REQUIREMENTS
Enable automatic management of the Paging file
WIN + PAUSE/BREAK key combo |
Advanced system settings (left-hand side) |
Advanced tab, Performance section, Settings |
Advanced tab, Virtual Memory section, Change |
checkmark Automatically manage paging file size for all drives |
OK | OK | OK
STARTUP AND RECOVERY SETTINGS
WIN + PAUSE/BREAK key combo |
Advanced system settings (left-hand side) |
Advanced tab, Startup and Recovery section, Settings |
System Failure section | checkmark Write an Event to the system log
| uncheck Automatically restart |
Under Write debugging information, select Small memory dump |
in the Small dump directory: box, enter %SystemRoot%\Minidump| OK
If Overwrite any existing file is checked, then:
Ø Under Write debugging information, select Kernel memory dump
Ø Uncheck Overwrite any existing file
Ø Under Write debugging information, select Small memory dump
Ø OK button
If you get a crazy message from Win 7 about your paging file being too small, then just ignore the message since we have already made sure that the paging file is set to be managed by Win 7.
ENABLE THE WINDOWS ERROR REPORTING SERVICE
WIN key | type SERVICES.MSC | ENTER |
Scroll down to Windows Error Reporting Service |
Rt-clk on Windows Error Reporting Service | Properties |
General tab | for Startup type, choose Automatic |
In Service status, Start button (unless grayed out) | OK
ASSURE THAT CCLEANER IS NOT DELETING DUMPS
CCLEANER | Cleaner icon | Windows tab | System category |
Uncheck Memory Dumps
· WINDOWS ERROR REPORTING SERVICE must NOT be disabled!
· WIN | Services.msc | Enter
· Under Name, locate Windows Error Reporting Service
· If Status is not Started, then
Right-click on Windows Error Reporting Service |choose START
· If Startup Type is not Automatic, then
Right-click on Windows Error Reporting Service |
choose Properties | General tab |
set Startup type to Automatic
· Close Services.msc (I like to use ALT + F4)
After a crash, the minidump file will be in %SystemRoot%\Minidump
%SystemRoot% is generally C:\Windows
=========================================================
=========================================================
After that, then attach the minidumpsettings.txt file created by following script.
That's how I can confirm that all required settings have been made.
# **********************INSTRUCTIONS**************************
# STEP 1 ** RUN POWERSHELL AS ADMINISTRATOR ******************
# ************************************************************
#
# WIN key | type POWERSHELL | do NOT hit ENTER |
# in the PROGRAMS list, right-click on WINDOWS POWERSHELL |
# choose "Run as administrator" |
# Click on the YES button (if such appears)
#
# WIN key = key with Microsoft log on top
#
# for the guru:
# WIN | type POWERSHELL | CTRL+SHIFT+ENTER key combo | ALT+Y keycombo
# ************************************************************
# STEP 2 ** COPY AND PASTE ***********************************
# ************************************************************
#
# COPY the script using CTRL+C,
# COPY every line of script down thru both EXIT statements
#
# PASTE into Powershell
#----Right-Click at the PowerShell Prompt
#----(Ctrl+V does not work)
#
# Start copying with first script line without a # at start of the line
# Note: Actually, you can paste the entire file if you rather
#-------Lines starting with a # are ignored by PowerShell
# ************************************************************
# STEP 3 ** SCRIPT OUTPUT & SCRIPT PURPOSE *******************
# ************************************************************
# --The script output and purpose is given at the very front of the script
#
# --The script output and purpose is given at the very front of the script
#
# ************************************************************
# ***************** NOTE - POWERSHELL VERSION*****************
# if you receive this error msg:
#--The system can not find the path specified
# you may need to update your PowerShell
# you must be using Powershell 2.0 or later.
#
# To determine your Powershell version:
#---Run PowerShell
#---enter $host.version
#---you should see at least:
# Major Minor Build Revision
# ----- ----- ----- --------
# 2......0......-1.....-1
#
# If you do not see the above, update your Vista/Win 7.
# ************************************************************
# *************** NOTE - EXECUTION POLICY*********************
# If you haven't set the execution policy, you may need to:
#---Run PowerShell
#---enter SET-EXECUTIONPOLICY -EXECUTIONPOLICY REMOTESIGNED
# ************************************************************
Script:
# **************************************************************
# Puts MiniDumpSettings.TXT in your user profile folder
# WIN | type %userprofile%\ then click on MiniDumpSettings.TXT
# to view the important minidump settings
# WIN = key with Microsoft logo on top
# **************************************************************
gwmi Win32_OSRecoveryConfiguration |
select minidumpdirectory, expandedminidumpdirectory, overwriteexistingdebugfile, kerneldumponly,`
debuginfotype, autoreboot, writedebuginfo, writetosystemlog | fl > $env:userprofile\desktop\minidumpsettings.txt
EXIT
EXIT
ok here's the mini dump file
Please reread the procedure for fulfilling minidump requirements.
A couple of your settings are wrong.
Well I won't need to I don't know what you had me do or why it has recently stopped but thank you so much for all your help!