Windows 7 Forums

Welcome to Windows 7 Forums. Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks.


Windows 7: BSOD on fresh morning startup.

16 Sep 2012   #1
theArtizan

Windows 7 Ultimate x64 SP1
 
 
BSOD on fresh morning startup.

Hi,

my first post and it's a big problem I have. Thank you in advance for any kind of help.
My computer specs are these:

Windows 7 Ultimate 64bit (SP1 updated)
Motherboard: Gigabyte EX58-UD5
Chip: Intel i7 920 2.67GHz
RAM: 12 GB (6sticks of 2Gb each)
Graphics card: nvidia gtx 285
HDD: 5 HDDs

Freezing at fresh morning boot!
During the night I shut down my computer (saving some electricity and I'm not downloading much, lol).
At first boot it shows all RAM and disc at check in the 1st DOS window.
During the end of August 2012 it started to freeze every second day.
I have a Logitech G500 mouse which has lights on it for showing the scroll wheel speed. Those never turn off, except when the PC if off.
When it froze the lights went off (completely dead) and so did the keyboard (no caps lock light). Couldn't do anything except hard rebooting the system.
As I did that it showed only 8GB RAM.
I went into BIOS and upped the voltage of RAM, after investigating on the internet about the Gigabyte EX58-UD5 problems recognizing all RAM.

After that it was good for a week and than it started again. I started to manually up the voltage of the VVT, reading several forums, but never into the PINK area or even in the RED. I was allways carefull.

BSOD at the morning boot!
Now for the past 2 weeks I've experienced BSOD several times, every time in the morning boot.
I thought maybe I set the BIOS voltage too high and revert everything back to AUTO settings except the RAM voltage I left at 1.6.
Now this morning as I boot, it happened again. After 5-10 minutes BSOD.
It rebooted itself (even though it never did before) and
- it failed to move from the first BIOS screen. It checked all RAM, but stopped at the 4th HDD. Didn't move forward. (Here it gives me thinking it's a HDD problem, maybe). I hard booted again, sadly.
- it stopped again just before the Welcome screen. You know the little Windows sign, that forms itself from 4 colors/corners. It FROZE and I hardbooted again.
- I tried a Window restore/repair but it was unable to repair anything.
- After that it rebooted again and I chose 'Start windows normally'.

I'm pretty confident that the PC will work without skipping a beat for the whole day, until I boot it up in the morning, where I'll have to go through this again.

Final note about BSOD:
Today (Sunday 16.9.2012) BSOD after 5-10 minutes (read above description).
Yesterday (Sat.) BSOD after 5-10 minutes, but after the hard reboot it went into Win normally.
Friday I turned it on only around 7PM and no problem untill 11PM when I shut it down for the night.
Thursday it froze in the first 5-10 minutes of morning boot.
Wednesday and Tuesday no problems...
I'm fighting with my PC instead of using it. Searching the internet for a solution instead of working.

If I had this PC for personal use (gaming, surfing the internet,...) I'd probably continue searching for a possible solution, but I have it for work (graphis desing, 3D artist) and I need it, without loosing countless hours checking the internet for possible solutions.

So I turn to you. You have experience I DON'T. You have probably seen these kind of problems before. I politely REQUEST your help to solve this.

Thank you again in advance for any help you will be able to provide.

P.S. I have attached 2 files.
TheArtizan.zip is the file created from the SF Diagnostic tools (Grab all) tutorial here on the site.
091612-21216-01.txt is the minidump file I changed the extension to TXT to attach it here.

P.P.S. Sorry for the long post, but I thought the more info the better.


My System SpecsSystem Spec
.
16 Sep 2012   #2
koolkat77

Microsoft Community Contributor Award Recipient

Windows 10 Home 64Bit
 
 

Welcome

All your dumps are corrupted. Could you upload them again following the instructions carefully,
http://www.sevenforums.com/crashes-d...tructions.html
My System SpecsSystem Spec
16 Sep 2012   #3
theArtizan

Windows 7 Ultimate x64 SP1
 
 

I re-Grabbed everything again.
I hope it's good this time around.

cheers
My System SpecsSystem Spec
.

16 Sep 2012   #4
koolkat77

Microsoft Community Contributor Award Recipient

Windows 10 Home 64Bit
 
 

2 of your dumps still don't load.

Information I got from one:

BSOD Index STOP 0x0000007E: SYSTEM_THREAD_EXCEPTION_NOT_HANDLED

Usual causes: Insufficient disk space, Device driver, Video card, BIOS, Breakpoint with no debugger attached, Hardware incompatibility, Faulty system service, Memory, 3rd party remote control


Code:
*******************************************************************************
*                                                                             *
*                        Bugcheck Analysis                                    *
*                                                                             *
*******************************************************************************

Use !analyze -v to get detailed debugging information.

BugCheck 1000007E, {ffffffffc0000005, fffff8800742143a, fffff880053f1618, fffff880053f0e70}

Probably caused by : memory_corruption

Followup: memory_corruption
---------

2: kd> !analyze -v
*******************************************************************************
*                                                                             *
*                        Bugcheck Analysis                                    *
*                                                                             *
*******************************************************************************

SYSTEM_THREAD_EXCEPTION_NOT_HANDLED_M (1000007e)
This is a very common bugcheck.  Usually the exception address pinpoints
the driver/function that caused the problem.  Always note this address
as well as the link date of the driver/image that contains this address.
Some common problems are exception code 0x80000003.  This means a hard
coded breakpoint or assertion was hit, but this system was booted
/NODEBUG.  This is not supposed to happen as developers should never have
hardcoded breakpoints in retail code, but ...
If this happens, make sure a debugger gets connected, and the
system is booted /DEBUG.  This will let us see why this breakpoint is
happening.
Arguments:
Arg1: ffffffffc0000005, The exception code that was not handled
Arg2: fffff8800742143a, The address that the exception occurred at
Arg3: fffff880053f1618, Exception Record Address
Arg4: fffff880053f0e70, Context Record Address

Debugging Details:
------------------


EXCEPTION_CODE: (NTSTATUS) 0xc0000005 - The instruction at 0x%08lx referenced memory at 0x%08lx. The memory could not be %s.

FAULTING_IP: 
dxgmms1!VIDMM_GLOBAL::FindResourcesForOneAllocation+31e
fffff880`0742143a 0fba635415      bt      dword ptr [rbx+54h],15h

EXCEPTION_RECORD:  fffff880053f1618 -- (.exr 0xfffff880053f1618)
ExceptionAddress: fffff8800742143a (dxgmms1!VIDMM_GLOBAL::FindResourcesForOneAllocation+0x000000000000031e)
   ExceptionCode: c0000005 (Access violation)
  ExceptionFlags: 00000000
NumberParameters: 2
   Parameter[0]: 0000000000000000
   Parameter[1]: 00000000000000c4
Attempt to read from address 00000000000000c4

CONTEXT:  fffff880053f0e70 -- (.cxr 0xfffff880053f0e70)
rax=0000000000000000 rbx=0000000000000070 rcx=0000000000000001
rdx=fffffa800d172ad0 rsi=0000000000000000 rdi=fffffa800c4e2000
rip=fffff8800742143a rsp=fffff880053f1850 rbp=0000000000000000
 r8=0000000000000101  r9=0000000000000000 r10=0000000000000000
r11=0000000000000006 r12=0000000000000000 r13=0000000000000000
r14=fffffa800d172ad0 r15=0000000000000000
iopl=0         nv up ei pl zr na po nc
cs=0010  ss=0018  ds=002b  es=002b  fs=0053  gs=002b             efl=00010246
dxgmms1!VIDMM_GLOBAL::FindResourcesForOneAllocation+0x31e:
fffff880`0742143a 0fba635415      bt      dword ptr [rbx+54h],15h ds:002b:00000000`000000c4=????????
Resetting default scope

CUSTOMER_CRASH_COUNT:  1

PROCESS_NAME:  System

CURRENT_IRQL:  0

ERROR_CODE: (NTSTATUS) 0xc0000005 - The instruction at 0x%08lx referenced memory at 0x%08lx. The memory could not be %s.

EXCEPTION_PARAMETER1:  0000000000000000

EXCEPTION_PARAMETER2:  00000000000000c4

READ_ADDRESS: GetPointerFromAddress: unable to read from fffff800030ff0e8
 00000000000000c4 

FOLLOWUP_IP: 
dxgmms1!VIDMM_GLOBAL::FindResourcesForOneAllocation+31e
fffff880`0742143a 0fba635415      bt      dword ptr [rbx+54h],15h

BUGCHECK_STR:  0x7E

DEFAULT_BUCKET_ID:  CODE_CORRUPTION

LAST_CONTROL_TRANSFER:  from fffff8800741e1cc to fffff8800742143a

STACK_TEXT:  
fffff880`053f1850 fffff880`0741e1cc : 00000000`00000000 00000000`00000000 00000000`00000001 fffffa80`00000000 : dxgmms1!VIDMM_GLOBAL::FindResourcesForOneAllocation+0x31e
fffff880`053f1910 fffff880`0743865d : 00000000`00000000 fffff8a0`00a45510 fffffa80`00000000 fffffa80`0db31770 : dxgmms1!VIDMM_GLOBAL::PrepareDmaBuffer+0x738
fffff880`053f1ae0 fffff880`07438398 : fffff800`00b96080 fffff880`07437d00 fffffa80`00000000 fffffa80`00000000 : dxgmms1!VidSchiSubmitRenderCommand+0x241
fffff880`053f1cd0 fffff880`07437e96 : 00000000`00000000 fffffa80`0db4e4c0 00000000`00000080 fffffa80`0c4bb010 : dxgmms1!VidSchiSubmitQueueCommand+0x50
fffff880`053f1d00 fffff800`0316bcce : 00000000`0296e64c fffffa80`0c4e1770 fffffa80`0973c040 fffffa80`0c4e1770 : dxgmms1!VidSchiWorkerThread+0xd6
fffff880`053f1d40 fffff800`02ebffe6 : fffff800`03040e80 fffffa80`0c4e1770 fffff800`0304ecc0 fffff880`0122b384 : nt!PspSystemThreadStartup+0x5a
fffff880`053f1d80 00000000`00000000 : fffff880`053f2000 fffff880`053ec000 fffff880`053f1400 00000000`00000000 : nt!KxStartSystemThread+0x16


CHKIMG_EXTENSION: !chkimg -lo 50 -d !dxgmms1
    fffff88007421148 - dxgmms1!VIDMM_GLOBAL::FindResourcesForOneAllocation+2c
	[ 8b:8a ]
1 error : !dxgmms1 (fffff88007421148)

MODULE_NAME: memory_corruption

IMAGE_NAME:  memory_corruption

FOLLOWUP_NAME:  memory_corruption

DEBUG_FLR_IMAGE_TIMESTAMP:  0

MEMORY_CORRUPTOR:  ONE_BIT

STACK_COMMAND:  .cxr 0xfffff880053f0e70 ; kb

FAILURE_BUCKET_ID:  X64_MEMORY_CORRUPTION_ONE_BIT

BUCKET_ID:  X64_MEMORY_CORRUPTION_ONE_BIT

Followup: memory_corruption
---------

2: kd> !analyze -v
*******************************************************************************
*                                                                             *
*                        Bugcheck Analysis                                    *
*                                                                             *
*******************************************************************************

SYSTEM_THREAD_EXCEPTION_NOT_HANDLED_M (1000007e)
This is a very common bugcheck.  Usually the exception address pinpoints
the driver/function that caused the problem.  Always note this address
as well as the link date of the driver/image that contains this address.
Some common problems are exception code 0x80000003.  This means a hard
coded breakpoint or assertion was hit, but this system was booted
/NODEBUG.  This is not supposed to happen as developers should never have
hardcoded breakpoints in retail code, but ...
If this happens, make sure a debugger gets connected, and the
system is booted /DEBUG.  This will let us see why this breakpoint is
happening.
Arguments:
Arg1: ffffffffc0000005, The exception code that was not handled
Arg2: fffff8800742143a, The address that the exception occurred at
Arg3: fffff880053f1618, Exception Record Address
Arg4: fffff880053f0e70, Context Record Address

Debugging Details:
------------------


EXCEPTION_CODE: (NTSTATUS) 0xc0000005 - The instruction at 0x%08lx referenced memory at 0x%08lx. The memory could not be %s.

FAULTING_IP: 
dxgmms1!VIDMM_GLOBAL::FindResourcesForOneAllocation+31e
fffff880`0742143a 0fba635415      bt      dword ptr [rbx+54h],15h

EXCEPTION_RECORD:  fffff880053f1618 -- (.exr 0xfffff880053f1618)
ExceptionAddress: fffff8800742143a (dxgmms1!VIDMM_GLOBAL::FindResourcesForOneAllocation+0x000000000000031e)
   ExceptionCode: c0000005 (Access violation)
  ExceptionFlags: 00000000
NumberParameters: 2
   Parameter[0]: 0000000000000000
   Parameter[1]: 00000000000000c4
Attempt to read from address 00000000000000c4

CONTEXT:  fffff880053f0e70 -- (.cxr 0xfffff880053f0e70)
rax=0000000000000000 rbx=0000000000000070 rcx=0000000000000001
rdx=fffffa800d172ad0 rsi=0000000000000000 rdi=fffffa800c4e2000
rip=fffff8800742143a rsp=fffff880053f1850 rbp=0000000000000000
 r8=0000000000000101  r9=0000000000000000 r10=0000000000000000
r11=0000000000000006 r12=0000000000000000 r13=0000000000000000
r14=fffffa800d172ad0 r15=0000000000000000
iopl=0         nv up ei pl zr na po nc
cs=0010  ss=0018  ds=002b  es=002b  fs=0053  gs=002b             efl=00010246
dxgmms1!VIDMM_GLOBAL::FindResourcesForOneAllocation+0x31e:
fffff880`0742143a 0fba635415      bt      dword ptr [rbx+54h],15h ds:002b:00000000`000000c4=????????
Resetting default scope

CUSTOMER_CRASH_COUNT:  1

PROCESS_NAME:  System

CURRENT_IRQL:  0

ERROR_CODE: (NTSTATUS) 0xc0000005 - The instruction at 0x%08lx referenced memory at 0x%08lx. The memory could not be %s.

EXCEPTION_PARAMETER1:  0000000000000000

EXCEPTION_PARAMETER2:  00000000000000c4

READ_ADDRESS:  00000000000000c4 

FOLLOWUP_IP: 
dxgmms1!VIDMM_GLOBAL::FindResourcesForOneAllocation+31e
fffff880`0742143a 0fba635415      bt      dword ptr [rbx+54h],15h

BUGCHECK_STR:  0x7E

DEFAULT_BUCKET_ID:  CODE_CORRUPTION

LAST_CONTROL_TRANSFER:  from fffff8800741e1cc to fffff8800742143a

STACK_TEXT:  
fffff880`053f1850 fffff880`0741e1cc : 00000000`00000000 00000000`00000000 00000000`00000001 fffffa80`00000000 : dxgmms1!VIDMM_GLOBAL::FindResourcesForOneAllocation+0x31e
fffff880`053f1910 fffff880`0743865d : 00000000`00000000 fffff8a0`00a45510 fffffa80`00000000 fffffa80`0db31770 : dxgmms1!VIDMM_GLOBAL::PrepareDmaBuffer+0x738
fffff880`053f1ae0 fffff880`07438398 : fffff800`00b96080 fffff880`07437d00 fffffa80`00000000 fffffa80`00000000 : dxgmms1!VidSchiSubmitRenderCommand+0x241
fffff880`053f1cd0 fffff880`07437e96 : 00000000`00000000 fffffa80`0db4e4c0 00000000`00000080 fffffa80`0c4bb010 : dxgmms1!VidSchiSubmitQueueCommand+0x50
fffff880`053f1d00 fffff800`0316bcce : 00000000`0296e64c fffffa80`0c4e1770 fffffa80`0973c040 fffffa80`0c4e1770 : dxgmms1!VidSchiWorkerThread+0xd6
fffff880`053f1d40 fffff800`02ebffe6 : fffff800`03040e80 fffffa80`0c4e1770 fffff800`0304ecc0 fffff880`0122b384 : nt!PspSystemThreadStartup+0x5a
fffff880`053f1d80 00000000`00000000 : fffff880`053f2000 fffff880`053ec000 fffff880`053f1400 00000000`00000000 : nt!KxStartSystemThread+0x16


CHKIMG_EXTENSION: !chkimg -lo 50 -d !dxgmms1
    fffff88007421148 - dxgmms1!VIDMM_GLOBAL::FindResourcesForOneAllocation+2c
	[ 8b:8a ]
1 error : !dxgmms1 (fffff88007421148)

MODULE_NAME: memory_corruption

IMAGE_NAME:  memory_corruption

FOLLOWUP_NAME:  memory_corruption

DEBUG_FLR_IMAGE_TIMESTAMP:  0

MEMORY_CORRUPTOR:  ONE_BIT

STACK_COMMAND:  .cxr 0xfffff880053f0e70 ; kb

FAILURE_BUCKET_ID:  X64_MEMORY_CORRUPTION_ONE_BIT

BUCKET_ID:  X64_MEMORY_CORRUPTION_ONE_BIT

Followup: memory_corruption
---------
Suggestions:

Run memtest86+ on each stick for 8 passes preferably overnight:
RAM - Test with Memtest86+

Do post back results.

I've also called a friend to take a look at your problem and suggest something.
My System SpecsSystem Spec
17 Sep 2012   #5
theArtizan

Windows 7 Ultimate x64 SP1
 
 

Hi,

I ran memtest over night and it showed 0 errors.

Any other suggestions, perhaps?

I didn't have a BSOD or freezing now, since the Computer was on all night.


cheers
My System SpecsSystem Spec
17 Sep 2012   #6
koolkat77

Microsoft Community Contributor Award Recipient

Windows 10 Home 64Bit
 
 

To make sure that hard drive is good run disk check following this tutorial:
Disk Check
Hard drive scan usings SeaTools:
SeaTools | Seagate both long and short tests.
My System SpecsSystem Spec
17 Sep 2012   #7
theArtizan

Windows 7 Ultimate x64 SP1
 
 

Just a minor update.

I've checked 3 of 5 discs yesterday. No errors or bad sectors.

10 minutes ago I have booted my PC (just woke up) and after 3 minutes the BSOD. It was a fast one. A second and then the PC rebooted itself.
I hit start Windows normally and here I am. Probably the PC will work fine untill tomorrow mornings boot.

I'm attaching today's SF diagnostic tools RAR file. I hope it grabbed it OK.

Now, I'm going to check the last 2 discs.

Have a nice day.

P.S. koolkat77, just a THANK YOU for the suggestions and help. I appreciate it.
My System SpecsSystem Spec
18 Sep 2012   #8
koolkat77

Microsoft Community Contributor Award Recipient

Windows 10 Home 64Bit
 
 

STOP 0x00000024: NTFS_FILE_SYSTEM BSOD Index

Usual causes: Disk corruption, insufficient physical memory, Device driver, Indexing, Resident antivirus, backup, defrag programs, Disk/Drive failing/failure

If you are overclocking any hardware, please stop.

Problematic software
Code:
Start Menu\Programs\Autodesk	Public:Start Menu\Programs\Autodesk	Public
Start Menu\Programs\COMODO	Public:Start Menu\Programs\COMODO	Public
Start Menu\Programs\COMODO\COMODO Internet Security	Public:Start Menu\Programs\COMODO\COMODO Internet Security	Public
Start Menu\Programs\DAEMON Tools Lite	Public:Start Menu\Programs\DAEMON Tools Lite	Public
Please revert to factory clocks if you're overclocking.
Please uninstall Autodesk and all its components from add/remove programs. (You may install this back afterwards.)
Quote:
- Anti-Virus Removal:
Please do the following:
- download a free antivirus for testing purposes:
(Most preferable = Microsoft Security Essentials - Free Antivirus for Windows)
- uninstall the Comodo Internet Security from your system (you can reinstall it, if so desired, when we're done troubleshooting)
- remove any remnants of Comodo Internet Security using this free tool: http://forums.comodo.com/index.php?a...0;attach=17692 (Requires registration)
- IMMEDIATELY install and update the free antivirus
- check to see if this fixes the BSOD's
NOTE: NEVER run more than 1 anti-virus, firewall, Internet Security/Security Center application at the same time.
Scan the system once you've installed and updated MSE

Run the system file checker for damaged windows files:
SFC /SCANNOW Command - System File Checker
Use Speccy to monitor all hardware temperatures:
Speccy - System Information - Free Download

Also look for a update on your BIOS version
Code:
BIOS Version/Date	Award Software International, Inc. F12, 11.3.2010
Let me know if you get more blue screens
My System SpecsSystem Spec
18 Sep 2012   #9
theArtizan

Windows 7 Ultimate x64 SP1
 
 

Hi,

yesterday I checked the final 2 discs, no bad sectors no errors.

So, I decided I would put the BIOS in default factory settings and see from there. I think that I only manually set the Voltage of RAM to 1.5 and put everything back to AUTO (as set originally) last week.

Anyways, I booted up the PC, in the first DOC window it checked all 12Gb RAM normally and all 5 HDDs.
I hit DEL to go into BIOS and there I hit F11 to save the settings I changed (I'm paranoid like that).
I hit enter without changing the name of the profile and it gave me a warning that it did not save because I didn't change the name. I hit F11 again and changed the name and hit ENTER.
Nothing happened. The PC froze completely. The keyboard was dead. (I'll mention also that the light on the mouse (scroll wheel speed monitor) was ON. Might not be important, but it's just an additional info.)
- I wait, to see if BIOS wakes up but nothing. I hardboot the PC. It arrives to the Starting Windows screen (black background, Windows LOGO) and the monitor looses signal, even if the PC sounds normal, no rebooting.
- I hardboot again. It arrives again to the Starting Windows screen and freezes there. I leave it to see if it goes into Windows again. Nothing.
- I hard boot again and this time it goes normally into Windows.

As optimistic as I Am I'm slowly starting to get discouraged by all these problems. I have ZERO ideas what is going on here.
The RAM checked out good with MemTest, the DISCS checked out good as well.

The Power Supply is 650W, so it's not a lack of electricity at first boot.

Now, it has passed more than 30 minutes from the time the PC booted in Windows successfully and no freezes or BSOD, which means that are those first 3-5 minutes the problem.
Does my PC needs a fresh cup of coffe to start it's day? LOL

Have a nice day.

EDIT: I reverted the BIOS back to 'Fail-Safe defaults'. Atleast that's what was written in BIOS, heh.
Funny thing. As I came into Windows, it recognized a new hardware, a Floppy Disc (A). I DON'T even have a floppy disc. No use for it. My head is starting to hurt from all of this.
My System SpecsSystem Spec
18 Sep 2012   #10
koolkat77

Microsoft Community Contributor Award Recipient

Windows 10 Home 64Bit
 
 

Thanks for the feedback.

Were you able uninstall the programs I listed?
Monitor your computer temp with Speccy?
My System SpecsSystem Spec
Reply

 BSOD on fresh morning startup.




Thread Tools Search this Thread
Search this Thread:

Advanced Search




Similar help and support threads
Thread Forum
BSOD on Startup This Morning
Hi all, I'm new to this, but everything I read online said this was the best place to start with this. I followed the instructions on creating and attaching a BSOD zip file, so hopefully this works and hopefully someone can help me. Thank ya kindly.
BSOD Help and Support
BSOD twice this morning
One of my users, had a BSOD twice this morning, within an hour. Says she only had Outlook, IE, Excel, and an accounting program open both times. She did not write down the error message. So all I have is the Zip file created from the SF Diag tool. Any help would be appreciated.
BSOD Help and Support
BSOD on every startup with fresh install of Windows 7
Some background: I accidentally wiped my hard drive over the weekend (thankfully I backed most of my homework up). I had been experiencing startup issues and was playing around with the hard drive configurations. I know what went wrong - I was trying to put my SSD back into RAID mode and it...
BSOD Help and Support
BSOD this morning
HP dv6 laptop Intel I7 OEM Win7X64 upgraded to Win pro Hello, This forum has helped me in the past and I hope someone will analize the attached log file. The computer blue screens/(Driver-IRQL_NOT_LESS_OR_EQUAL) on boot. 1. I tried system restore and it seemed to restore, but did it...
BSOD Help and Support
Two BSOD's this morning..Please help
Please help..Everything was fine until this morning.... 060610-14773-01.dmp 6/6/2010 10:06:17 AM BAD_POOL_HEADER 0x00000019 00000000`00000003 fffffa80`03661760 fffffa80`03661760 d7fffa80`03661760 PSINFile.sys ...
BSOD Help and Support
Random BSOD - Fresh install, fresh system
Hi. I have installed a whole new windows 7 pro x64. My new mobo an ASus p5e3 pro along with new ram pc12800 gskill 2x2 ddr3 (running in 1066mhz due to my q6600) Everythingi s running perfectly...except some random BSOD. 4 total this week. I have posted a pack of dump file in here, the last 4...
BSOD Help and Support


Our Sites

Site Links

About Us

Find Us

Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

Designer Media Ltd

All times are GMT -5. The time now is 21:33.

Twitter Facebook Google+



Windows 7 Forums

Seven Forums Android App Seven Forums IOS App