Take your time.
Just so you know the usual causes on your bug check:
Code:
STOP 0x0000007E: SYSTEM_THREAD_EXCEPTION_NOT_HANDLED
Usual causes: Insufficient disk space, Device driver, Video card, BIOS,
Breakpoint with no debugger attached, Hardware incompatibility,
Faulty system service, Memory, 3rd party remote control,
(Source: BSOD Index)
Code:
*******************************************************************************
* *
* Bugcheck Analysis *
* *
*******************************************************************************
Use !analyze -v to get detailed debugging information.
BugCheck 1000007E, {ffffffffc0000006, fffff88000cf90e9, fffff88007891638, fffff88007890e90}
Probably caused by : hardware_disk
Followup: MachineOwner
---------
2: kd> !analyze -v
*******************************************************************************
* *
* Bugcheck Analysis *
* *
*******************************************************************************
SYSTEM_THREAD_EXCEPTION_NOT_HANDLED_M (1000007e)
This is a very common bugcheck. Usually the exception address pinpoints
the driver/function that caused the problem. Always note this address
as well as the link date of the driver/image that contains this address.
Some common problems are exception code 0x80000003. This means a hard
coded breakpoint or assertion was hit, but this system was booted
/NODEBUG. This is not supposed to happen as developers should never have
hardcoded breakpoints in retail code, but ...
If this happens, make sure a debugger gets connected, and the
system is booted /DEBUG. This will let us see why this breakpoint is
happening.
Arguments:
Arg1: ffffffffc0000006, The exception code that was not handled
Arg2: fffff88000cf90e9, The address that the exception occurred at
Arg3: fffff88007891638, Exception Record Address
Arg4: fffff88007890e90, Context Record Address
Debugging Details:
------------------
EXCEPTION_CODE: (NTSTATUS) 0xc0000006 - The instruction at 0x%p referenced memory at 0x%p. The required data was not placed into memory because of an I/O error status of 0x%x.
FAULTING_IP:
CI!MinCrypK_GetCertAlgId+45
fffff880`00cf90e9 66394104 cmp word ptr [rcx+4],ax
EXCEPTION_RECORD: fffff88007891638 -- (.exr 0xfffff88007891638)
ExceptionAddress: fffff88000cf90e9 (CI!MinCrypK_GetCertAlgId+0x0000000000000045)
ExceptionCode: c0000006 (In-page I/O error)
ExceptionFlags: 00000000
NumberParameters: 3
Parameter[0]: 0000000000000000
Parameter[1]: 00000000000ee204
Parameter[2]: 00000000c0000185
Inpage operation failed at 00000000000ee204, due to I/O error 00000000c0000185
CONTEXT: fffff88007890e90 -- (.cxr 0xfffff88007890e90)
rax=0000000000000200 rbx=0000000000000000 rcx=00000000000ee200
rdx=0000000000001c50 rsi=0000000000000000 rdi=0000000000000000
rip=fffff88000cf90e9 rsp=fffff88007891870 rbp=0000000000000000
r8=000007fffffeffff r9=fffff88007891968 r10=0000000000000000
r11=0000000000000000 r12=fffff8a00000fef0 r13=0000000000000000
r14=0000000000000000 r15=fffff8800316a040
iopl=0 nv up ei pl zr na po nc
cs=0010 ss=0018 ds=002b es=002b fs=0053 gs=002b efl=00010246
CI!MinCrypK_GetCertAlgId+0x45:
fffff880`00cf90e9 66394104 cmp word ptr [rcx+4],ax ds:002b:00000000`000ee204=????
Resetting default scope
CUSTOMER_CRASH_COUNT: 1
DEFAULT_BUCKET_ID: VISTA_DRIVER_FAULT
PROCESS_NAME: System
CURRENT_IRQL: 0
ERROR_CODE: (NTSTATUS) 0xc0000006 - The instruction at 0x%p referenced memory at 0x%p. The required data was not placed into memory because of an I/O error status of 0x%x.
EXCEPTION_PARAMETER1: 0000000000000000
EXCEPTION_PARAMETER2: 00000000000ee204
EXCEPTION_PARAMETER3: 00000000c0000185
IO_ERROR: (NTSTATUS) 0xc0000185 - The I/O device reported an I/O error.
BUGCHECK_STR: 0x7E
EXCEPTION_STR: 0xc0000006_c0000185
FOLLOWUP_IP:
+45
00000000`000ee204 ?? ???
FOLLOWUP_NAME: MachineOwner
MODULE_NAME: hardware_disk
IMAGE_NAME: hardware_disk
DEBUG_FLR_IMAGE_TIMESTAMP: 0
STACK_COMMAND: kb
FAILURE_BUCKET_ID: X64_0x7E_IMAGE_hardware_disk
BUCKET_ID: X64_0x7E_IMAGE_hardware_disk
Followup: MachineOwner