Windows 7 Forums

Welcome to Windows 7 Forums. Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks.


Windows 7: Random BSOD, error 0x0000000A

22 Dec 2012   #11
koolkat77

Microsoft Community Contributor Award Recipient

Windows 10 Home 64Bit
 
 

Have you taken memtest?


My System SpecsSystem Spec
.
22 Dec 2012   #12
ToxicFyre

Microsoft Windows 7 Home Premium 64-bit 7601 Multiprocessor Free Service Pack 1
 
 

Do you mean again?
Or the one I did before:
Stick 1 - 7 passes nor errors
Stick 2 - 16 passes no errors
Stick 1 and 2 at the same time: 7 passes no errors

(I previously removed stick 3 because it found two errors after 15 passes)

So should I make another memtest with these sticks? (1 and 2)
My System SpecsSystem Spec
22 Dec 2012   #13
koolkat77

Microsoft Community Contributor Award Recipient

Windows 10 Home 64Bit
 
 

Did you remove the stick or did you replace it?
How many sticks of RAM do you have exactly?

Is the firmware for your SSD up to date?
Code:
STOP 0x0000007F: UNEXPECTED_KERNEL_MODE_TRAP

Usual causes:  Memory corruption, Hardware (memory in particular), 
Overclocking failure, Installing a faulty or mismatched hardware 
(especially memory) or a failure after installing it, 3rd party firewall, 
Device drivers, SCSI/network/BIOS updates needed, Improperly seated cards, 
Incompatible storage devices, Overclocking, Virus scanner, Backup tool, 
Bad motherboard, Missing Service Pack
*******************************************************************************
*                                                                             *
*                        Bugcheck Analysis                                    *
*                                                                             *
*******************************************************************************

UNEXPECTED_KERNEL_MODE_TRAP (7f)
This means a trap occurred in kernel mode, and it's a trap of a kind
that the kernel isn't allowed to have/catch (bound trap) or that
is always instant death (double fault).  The first number in the
bugcheck params is the number of the trap (8 = double fault, etc)
Consult an Intel x86 family manual to learn more about what these
traps are. Here is a *portion* of those codes:
If kv shows a taskGate
        use .tss on the part before the colon, then kv.
Else if kv shows a trapframe
        use .trap on that value
Else
        .trap on the appropriate frame will show where the trap was taken
        (on x86, this will be the ebp that goes with the procedure KiTrap)
Endif
kb will then show the corrected stack.
Arguments:
Arg1: 0000000000000008, EXCEPTION_DOUBLE_FAULT
Arg2: 0000000080050033
Arg3: 00000000000006f8
Arg4: fffff80003a8051b

Debugging Details:
------------------


BUGCHECK_STR:  0x7f_8

CUSTOMER_CRASH_COUNT:  1

DEFAULT_BUCKET_ID:  WIN7_DRIVER_FAULT

PROCESS_NAME:  System

CURRENT_IRQL:  d

LAST_CONTROL_TRANSFER:  from fffff80003a89569 to fffff80003a89fc0

STACK_TEXT:  
fffff880`0368eee8 fffff800`03a89569 : 00000000`0000007f 00000000`00000008 00000000`80050033 00000000`000006f8 : nt!KeBugCheckEx
fffff880`0368eef0 fffff800`03a87a32 : 00000000`00000000 00000000`00000000 00000000`00000000 00000000`00000000 : nt!KiBugCheckDispatch+0x69
fffff880`0368f030 fffff800`03a8051b : 00000000`00000000 00000000`00000000 00000000`00000000 00000000`00000000 : nt!KiDoubleFaultAbort+0xb2
ffff7880`036b0a40 00000000`00000000 : 00000000`00000000 00000000`00000000 00000000`00000000 00000000`00000000 : nt!KeAccumulateTicks+0x2b


STACK_COMMAND:  kb

FOLLOWUP_IP: 
nt!KiDoubleFaultAbort+b2
fffff800`03a87a32 90              nop

SYMBOL_STACK_INDEX:  2

SYMBOL_NAME:  nt!KiDoubleFaultAbort+b2

FOLLOWUP_NAME:  MachineOwner

MODULE_NAME: nt

IMAGE_NAME:  ntkrnlmp.exe

DEBUG_FLR_IMAGE_TIMESTAMP:  503f82be

FAILURE_BUCKET_ID:  X64_0x7f_8_nt!KiDoubleFaultAbort+b2

BUCKET_ID:  X64_0x7f_8_nt!KiDoubleFaultAbort+b2

Followup: MachineOwner
---------
If you are overclocking your system, please return all overclocked components to their stock speeds.
If the BSOD's are found not to be caused by the overclock, you can re-overclock the components
to a stable speed once we have finished the diagnostics.
Code:
!sysinfo cpuspeed
CPUID:        "Intel(R) Core(TM) i7 CPU       X 990  @ 3.47GHz"
MaxSpeed:     3470
CurrentSpeed: 3549
Check for a more recent BIOS version.
Code:
BIOS Version/Date	American Megatrends Inc. 1401, 5/12/2011
Uninstall any overclocking software because it can lead to system instability and BSOD's.
Please reset all components to their stock speeds and then remove the software.

For monitoring the heat/celsius of the system, use Speccy or HWinfo:Perform a System File Check:
  • Click on the start
  • Type CMD on Search
  • Left click and Run as Administrator
  • Type SFC /scannow
Full tutorial here:Disk Check on your hard drive for file system errors and bad sectors on it:
My System SpecsSystem Spec
.

23 Dec 2012   #14
ToxicFyre

Microsoft Windows 7 Home Premium 64-bit 7601 Multiprocessor Free Service Pack 1
 
 

I have 3 RAM sticks.
There are three slots on my motherboard.
So when I test each stick I just remove the other two.
So stick one is in slot one, and stick two is in stick two.

The SSD, BIOS and overclocking seems complicated. I'll find out how to chack and do it, and get back to you later .

The my graphics card's max temperature is 91, and the processor's way below that.

File check found no errors, or corruptions.

Checking disk right now, will edit post when I get the results.

Thnaks for your help.
My System SpecsSystem Spec
23 Dec 2012   #15
koolkat77

Microsoft Community Contributor Award Recipient

Windows 10 Home 64Bit
 
 

Don't edit your post. It often goes un-noticed.
Post update on a new reply.
My System SpecsSystem Spec
23 Dec 2012   #16
ToxicFyre

Microsoft Windows 7 Home Premium 64-bit 7601 Multiprocessor Free Service Pack 1
 
 

Disk Check found no errors.
Now I'll try to figure out the hard stuff. Will post when done.
Thank you
My System SpecsSystem Spec
12 Jan 2013   #17
ToxicFyre

Microsoft Windows 7 Home Premium 64-bit 7601 Multiprocessor Free Service Pack 1
 
 

Ok. The bios is now updated, and the SSD was already updated.
I reseted the bios to defaults and the overclocking is gone. However every time I boot I get a message: "CPU Fan 1 Error". (I have water cooling in my processor, but everything else is fans)
I can just dismiss it with F1 and boot normally, but it keeps bothering me.
Will post again when a crash appears.

Thank you so much. Toxic
My System SpecsSystem Spec
14 Jan 2013   #18
koolkat77

Microsoft Community Contributor Award Recipient

Windows 10 Home 64Bit
 
 

Good to hear that the system is stable now.
I've requested a friend to take a look at your thread.

Please wait for a reply.
My System SpecsSystem Spec
14 Jan 2013   #19
Britton30
Microsoft MVP

Windows 7 Ultimate X64 SP1
 
 

Quote   Quote: Originally Posted by ToxicFyre View Post
Ok. The bios is now updated, and the SSD was already updated.
I reseted the bios to defaults and the overclocking is gone. However every time I boot I get a message: "CPU Fan 1 Error". (I have water cooling in my processor, but everything else is fans)
I can just dismiss it with F1 and boot normally, but it keeps bothering me.
Will post again when a crash appears.

Thank you so much. Toxic
That often happens with a water cooling system. You can plug in one of your fans to the CPU_FAN header or go to BIOS/UEFI fan control and set it so CPU fan monitoring is disabled or RPM limits ignored.
My System SpecsSystem Spec
15 Jan 2013   #20
ToxicFyre

Microsoft Windows 7 Home Premium 64-bit 7601 Multiprocessor Free Service Pack 1
 
 

I just got a crash. This one is different though, it's not a Blue Screen, my computer completely froze (but I was able to move my mouse). When I ctrl-alt-deleted it said Preparing Security Options or something like that, and it stayed like that until I plugged the computer off.
It was as if everything stopped responding, my mouse had the loading sign.
This isn't new though, a few days ago I started getting these along with the BSODs but I don't get the BSODs anymore.
I would also like to mention that when I boot right back again, and windows just starts, it happens again in the same way. (The freezing) I have to wait a few minutes to boot the computer again for it to be usable, and not get freezes at start-up.

I got this while playing BF3, although it's fair to say that my computer crashes way less after I removed the overclocking.
Thanks so much for your help guys, I appreciate it with all my being.
Here's my new crashlog:
My System SpecsSystem Spec
Reply

 Random BSOD, error 0x0000000A




Thread Tools Search this Thread
Search this Thread:

Advanced Search




Similar help and support threads
Thread Forum
BSOD random, error 0x0000000a
Hey, I am getting a BSOD since one a day randomly with the message IRQL_NOT_LESS_OR_EQUAL. BlueScreen Viewer showes me, that it is caused by the driver ntoskrnl.exe. This error happens randomly! My system specs are the following: CPU: Intel(R) Core(TM) i7-3770K CPU @ 3.50GHz...
BSOD Help and Support
BSOD at random intervals. Error 0x0000000a and 0x00000101
My BSOD screens are getting worse. My computer setup is below in the files. There is a change that I have done. I had a GTS 250 1GB Dark knight with the most recent driver. I was having several BSOD issues a day when in use. I went back to an older driver after completely removing the up to date...
BSOD Help and Support
Random BSOD , error 0x0000000a ( fltmgr.sys + ntoskrnl.exe)
Solved... :p Can be closed
BSOD Help and Support
Random BSOD, 3 crashes, error 0x000000d1, 0x0000000a, and 0x0000003b
I'm new to this whole crash analyzing thing so I'm sorry if a messed something up. I included the .zip in the attachments. Let me know if you need anything else. Thanks for the help!
BSOD Help and Support
BSOD (random) possibly after computer when to sleep, error 0x0000000A
I've seen random BSOD. 0) I run Windows memory test again and no errors found 1) First I suspected of eSata interface, but this was a guess, there was not really any proof 2) I suspected of a SW called MagicISO because I saw some reports about BSOD (but a guess again) 3) Then I suspected of...
BSOD Help and Support
Random BSOD - error 0x0000000a and 0x00000050
Been having random BSOD for the past week or so. Started on Sunday (11-27-11), where I had come back to my machine and it had been restarted... after logging in, find out that it was a BSOD. I then proceded to have 3 different BSOD events on Monday, which led me to perform a memtest on Tuesday...
BSOD Help and Support


Our Sites

Site Links

About Us

Find Us

Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

Designer Media Ltd

All times are GMT -5. The time now is 20:04.

Twitter Facebook Google+



Windows 7 Forums

Seven Forums Android App Seven Forums IOS App