Windows 7 Forums

Welcome to Windows 7 Forums. Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks.


Windows 7: BSOD after installing a D-Link Dual Band USB adapter

02 Mar 2013   #11
Cplc

Windows 7 home premium 64 bit
 
 

Yes it is internal Internet card and is Disabled.


My System SpecsSystem Spec
.
02 Mar 2013   #12
Cplc

Windows 7 home premium 64 bit
 
 

Yes it is the internal wireless card and it is disabled. I do not wish to use it.

But I do not know that is the Microsoft Virtual WiFi miniport adapter. Can it be the issue?
My System SpecsSystem Spec
02 Mar 2013   #13
Cplc

Windows 7 home premium 64 bit
 
 

I have found something interesting: When in safe mode, I have more Network adapter listed. There is also the following:
- Microsoft ISATAP Adapter
- Microsoft ISATAP Adapter #2
- Microsoft ISATAP Adapter #3
- Teredo Tunneling Pseuto-interface
- Wan miniport (IKEv2)
- Wan miniport (IPv6)
- Wan miniport (L2TP)
- Wan miniport (Network Monitor)
- Wan miniport (PPPOE)
- Wan miniport (PPTP)
- Wan miniport (SSTP)
My System SpecsSystem Spec
.

02 Mar 2013   #14
Arc

Microsoft Community Contributor Award Recipient

Microsoft Windows 10 Pro Insider Preview 64-bit
 
 

With the Pppoe (ethernet) connected, uninstall them one by one and then reboot. At reboot, the generic driver will be instslled. If not, install the network controller from your motherboard driver cd.

At least, it will make the system free from the new device driver caused bsods.
My System SpecsSystem Spec
02 Mar 2013   #15
VistaKing

Windows 7 Ultimate 32-Bit & Windows 7 Ultimate 64-Bit
 
 

Do you use IPv6 ? If not you could disable it .

To disable

follow these steps:
Click Start , and then click Control Panel.
Click Network and Sharing Center.
In the View your active networks area, click Local Area Connection, and then click Properties.
On the Networking tab, click to clear the Internet Protocol Version 6 (TCP/IPv6) check box, and then click OK.
My System SpecsSystem Spec
02 Mar 2013   #16
Cplc

Windows 7 home premium 64 bit
 
 

I was able to remove all except the following:
Wan miniport (IKEv2)
- Wan miniport (IPv6)
- Wan miniport (L2TP)
- Wan miniport (Network Monitor)
- Wan miniport (PPPOE)
- Wan miniport (PPTP)
- Wan miniport (SSTP)

I rebooted and still the same issue: BlueScreen with the same message.
My System SpecsSystem Spec
02 Mar 2013   #17
VistaKing

Windows 7 Ultimate 32-Bit & Windows 7 Ultimate 64-Bit
 
 

I'm not on the computer so I can't see the dmp file . Can you send me a private message with that info

Added: Do you use VPN ?
My System SpecsSystem Spec
02 Mar 2013   #18
Arc

Microsoft Community Contributor Award Recipient

Microsoft Windows 10 Pro Insider Preview 64-bit
 
 

Well, it is ALPHA Networks Filter Driver that is causing the crashes here.
Code:
*******************************************************************************
*                                                                             *
*                        Bugcheck Analysis                                    *
*                                                                             *
*******************************************************************************

Use !analyze -v to get detailed debugging information.

BugCheck D1, {fffff880068c7066, 2, 0, fffff88003946875}

*** WARNING: Unable to verify timestamp for anodlwfx.sys
*** ERROR: Module load completed but symbols could not be loaded for anodlwfx.sys
Probably caused by : anodlwfx.sys ( anodlwfx+2875 )

Followup: MachineOwner
---------
And that is very old.
Code:
fffff880`03944000 fffff880`0394d000   anodlwfx T (no symbols)           
    Loaded symbol image file: anodlwfx.sys
    Image path: \SystemRoot\system32\DRIVERS\anodlwfx.sys
    Image name: anodlwfx.sys
    Timestamp:        Fri Mar 06 15:40:08 2009 (49B0F680)
    CheckSum:         0000A8C3
    ImageSize:        00009000
    Translations:     0000.04b0 0000.04e4 0409.04b0 0409.04e4
Try to update it from Alpha Networks Inc..

The realtek network driver is also causing problems.
Code:
fffff880`03b8d7f8  fffff880`04f6afedUnable to load image \SystemRoot\system32\DRIVERS\Rt64win7.sys, Win32 error 0n2
*** WARNING: Unable to verify timestamp for Rt64win7.sys
*** ERROR: Module load completed but symbols could not be loaded for Rt64win7.sys
 Rt64win7+0x17fed
And it also needs to be updated.
Code:
fffff880`04f53000 fffff880`04ffb000   Rt64win7 T (no symbols)           
    Loaded symbol image file: Rt64win7.sys
    Image path: \SystemRoot\system32\DRIVERS\Rt64win7.sys
    Image name: Rt64win7.sys
    Timestamp:        Fri Feb 03 18:30:02 2012 (4F2BDA52)
    CheckSum:         000A655F
    ImageSize:        000A8000
    Translations:     0000.04b0 0000.04e4 0409.04b0 0409.04e4
Get the update from Realtek

When all the network components are failing with such a regularity, some other places are also to be looked. It is either an ambitious antivirus program that is causing the network blockage to protect the PC, or it is a virus playing there. I strongly recommend you that after updating the drivers, you uninstall Norton and all Symentec products using Norton Removal tool, at least as a test. Use Microsoft Security Essentials as your antivirus with windows inbuilt firewall, and free MBAM as the on demand scanner.
Download, install and update those, and then run full system scans with both of them, one by one. Also, scan the system for possible virus infection, too.
Free up the startup.
  1. Click on the Start button
  2. Type “msconfig (without quotes), click the resulting link. It will open the System Configuration window.
  3. Select the “Startup” tab.
  4. Deselect all items other than the antivirus.
  5. Apply > OK
  6. Accept then restart.
You have a lot of ASUS bloatware installed there. Uninstall them as they are not very much wanted.

Let us know the results.
My System SpecsSystem Spec
02 Mar 2013   #19
Cplc

Windows 7 home premium 64 bit
 
 

Hi, I've proceeded as you suggessed:
- I've done the 'get latest drive' for each and every drive and I get a message confirming that I hade the latest driver for them all... this is strange.
- After, I've uninstalled all norton products with Norton removal tool.
- I've downloaded Microsoft Security Essentials but it failed when updating the data...

After a seach on the causes of Microsoft Security Essentials update crash I've read something about windows update that might be the not functionning correctly. All investigations bring me to the latest windows updates that has been applied. Ane there it was! On the Fev. 27, 2013, a Windows update have been applied (in the same time as I was initially trying to install D-Link Dual Band USB Adapter.

The windows update that has been apprlied on Feb. 27, 2013 is KB2670838 dated from Fev. 27, 2013. It has been documented that this update make repeat Blue Screen crash. See the following link:
Feb 27 update causes Window 7 crashes - Microsoft Community

So, I've restore prior to that update and now it is functionnal.

I wish to thank you for your support. This is very appreciated.
My System SpecsSystem Spec
02 Mar 2013   #20
Arc

Microsoft Community Contributor Award Recipient

Microsoft Windows 10 Pro Insider Preview 64-bit
 
 

It's ok.

If there are further issues, let us know.
My System SpecsSystem Spec
Reply

 BSOD after installing a D-Link Dual Band USB adapter




Thread Tools Search this Thread
Search this Thread:

Advanced Search




Similar help and support threads
Thread Forum
Can't Dual Band/See 5 ghz network ... Linksys ea3500
Network mode: wireless n security: wpa2 personal channel width: 40 MHz channel: auto Linksys EA-3500
Network & Sharing
BSOD When pluged in TP-LINK Wireless adapter and trying to connect wif
I bought a new Tp-Link WN721N Wireless adapter and after starting it, when it was connecting the wireless network, a BSOD suddenly came. it happened for the first time.My pc is running on Windows Ultimate x64 i installed who crash it and this was the message i got On Fri 26/04/2013 8:59:47 AM...
BSOD Help and Support
buying laptop PCIe mini dual band adapter
Unfortunately, at my school you need a dual band wireless adapter in order to connect to the internet. With my current laptop, there are certain requirements it must meet in order for it to work. it must be a full height card. An adapter will not work as the antenna wires won't go that far....
Hardware & Devices
Looking for a wireless N dual band PCI card.
I got a new d-link wireless N router the other day which solved most of my slow internet problems. It is a dual band router and supports 5ghz but my current network card is only 2.4ghz. I'm in an apartment complex so I figure if I run it on the 5ghz band I will get much less interference from other...
Hardware & Devices
Simultaneous Dual-Band operation
I have a Linksys WRT600N router connected to my XP computer, and a Linksys WMP600N PCI adapter in my Windows 7 computer, and both are enabled with Dual-Band. I can connect to my 2.4GHz and my 5GHz connections just fine on my Windows 7 computer. My question is, can I connect to both at the same time...
Network & Sharing
Windows 7 64 wireless problem with dual band
Hello I have a new Toshiba A500 laptop with a Linksys 610 router, the max wireless connection is 70Mbit. Also have a Dell E5500 with Vista and have a wireless connection 150Mbit. On the Toshiba a have windows 7 64 as OS, standard on the laptop! The wireless chip is Realtek! Thanks Mike
Network & Sharing


Our Sites

Site Links

About Us

Find Us

Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

Designer Media Ltd

All times are GMT -5. The time now is 03:54.

Twitter Facebook Google+



Windows 7 Forums

Seven Forums Android App Seven Forums IOS App