Windows 7 Forums

Welcome to Windows 7 Forums. Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks.


Windows 7: 0x7b - 0xC34 - Win7 Pro 32bit

16 Mar 2013   #11
Arc

Microsoft Community Contributor Award Recipient

Microsoft Windows 10 Pro Insider Preview 64-bit
 
 

Boot to System Recovery Options . Try Safe Mode with Command Prompt. In the command prompt .... enter the command ....

start msconfig


It will open the system configuration window, with the "general" tab selected.
  • Click the "startup" tab. Click "Disable all" > Apply > OK.
  • Click on "services" tab. Check the "Hide all Microsoft Services"; Click "Disable all" > Apply > OK
Then try to boot again normally. Is it failing still?

If so, boot to System Recovery Options once again. Try Enable Boot Logging. It will create a file named ntbtlog.txt. Collect it and upload it. If you cannot do it within windows, Boot with a live Linux disc and collect it in a USB stick, use the usb stick in another computer and upload it. It is necessary.

BTW, if you can , post the data following the Blue Screen of Death (BSOD) Posting Instructions?


My System SpecsSystem Spec
.

16 Mar 2013   #12
Cosmitz

Win7 Pro 32bit
 
 

No Safemode gets past classpnp.

I can access the registry via the hive to HKLM\System\ControlSet2 (my default in Select and the one it's trying to boot)\services and disable whatever services i need disabling from there. And no, no other control set boots.

As i've mentioned, no minidump, no ntbtlog and no memory.dmp gets logged. CrashDumpEnabled is set for a complete dump also. I know ntbtlog should be in C:\Windows\ and no it's not there.


As for the BSOD posting instructions as mentioned, the system does not boot, i cannot use said app, and as far as i've seen, said app cannot retrieve them remotely even IF they would create. If i had a minidump to analyze via Bluescreenviewer, it would have been a piece of cake to solve.

Before posting this thread, i was trying to get the USB drivers to boot ahead of everything else, and have the minidump redirected to a USB stick if it can't write on the hard drives, seeing how they're both on SATA and share drivers.
My System SpecsSystem Spec
16 Mar 2013   #13
Arc

Microsoft Community Contributor Award Recipient

Microsoft Windows 10 Pro Insider Preview 64-bit
 
 

In such a situation it is better you start afresh.

First, move any data in the SSD that is important: Copy & Paste - in Windows Recovery Console

Then perform a Clean Reinstall - Factory OEM Windows 7
My System SpecsSystem Spec
.


16 Mar 2013   #14
Cosmitz

Win7 Pro 32bit
 
 

Not the help i was looking for. I could have backedup and reinstalled the system in under 30 minutes of the BSOD appearing, but i intend on making this install boot. Just thought i'd get more knowledgeable info on these forums.
My System SpecsSystem Spec
16 Mar 2013   #15
Arc

Microsoft Community Contributor Award Recipient

Microsoft Windows 10 Pro Insider Preview 64-bit
 
 

I requested gregrocker to look at your issue. He is offline now, so you have to wait.
My System SpecsSystem Spec
16 Mar 2013   #16
Cosmitz

Win7 Pro 32bit
 
 

Time i have, thanks for the assistance.

LE: Tried to get all the usb-related drivers in category group, WdfLoadGroup in my case, to load sooner, with all having set Start 0, but i'm missing something i guess, since the minidumps still aren't created, and i went through C: to F: setting the with two extra usb thumbdrives attached, trying to make it write on them in case it was bugging out writing on the system drive or the storage. I guess i also need to boot the file manager or something in that case, but i'm at a loss. Restored the original hive in any case, waiting on further info.
My System SpecsSystem Spec
16 Mar 2013   #17
gregrocker
Microsoft MVP

 
 

All repairs should be done with all other HD's and peripherals unplugged. If they weren't then do them over.

Your System boot files are corrupt and non-functioning as signified by no Boot flag on any partition in PW listings.

Try creating a new boot partition by Resizing Win7 by 200mb from the left, creating a New NTFS Primary partition there, marking it Active, then running 3 separate Startup Repairs which are the number required to check all parameters while also attempting to boot OS:
Partition Wizard Resize Partition - Video Help.
Partition Wizard Create Partition Video Help
How to Set Active/Inactive partition -Partition Wizard Video Help.

If this fails run Partition Wizard Partition surface test
My System SpecsSystem Spec
16 Mar 2013   #18
Cosmitz

Win7 Pro 32bit
 
 

Hello and good morning,

I did as you asked, disconnected everything minus the HDD in question. PW, resized 200mb from the left, new NTFS, Primary, Active. NTLDR missing. Loaded up Win7 disk, repair-try to boot, ntldr missing, repair, ntldr missing, repair, Starting Windows. 0x0000007B. Windows Startup repair this time, StartupRepairOffline/Autofailover/BadPatch. Second startup repair, Root cause, A patch is preventing the system from starting. Repair action, System files integrity check and repair. Third startup repair, repairing disk errors. Restart your computer to complete the repairs.

Starting windows... STOP:0x0000007B.

Did the surface test earlier today, but redid it for completeness' sake and it came out green across the board.
My System SpecsSystem Spec
16 Mar 2013   #19
gregrocker
Microsoft MVP

 
 

Try Partition Wizard Rebuild MBR - Video Help followed by 3 more Startup Repairs.

Then try the bootrec and bootsect commands as demonstrated in Troubleshooting Windows 7 Failure to Start, followed by Startup Repairs again.

You've now done everything possible to repair the boot. It may in fact be corruption in the OS (bad patch) blocking boot. Have you tried SFC /SCANNOW Run in Command Prompt at Boot?

Unfortunately a bad patch or Update is best remedied by System Restore. Do you think your Restore Points were intact before this? I'd try it again from DVD Recovery Options.
My System SpecsSystem Spec
16 Mar 2013   #20
Cosmitz

Win7 Pro 32bit
 
 

Repaired MBR via PW. 7B. Bootrec'd/bootsect'd, ran sfc /scannow /offbootdir /offwindir. Also, there are no restore points.

Let me reiterate what's happening:

Nothing will boot into windows, 7B at the windows logo. Safe mode loads drivers up to CLASSPNP.sys and then dies, see the first post attachements please. No minidumps, ntbtlogs or such are getting created on any drive that i try to path them to via CrashControl Controlset registry key. Besides my suspicion of Intel drivers, i also listed a full 0 and 1 start services/drivers with the ServiceGroup startups listed in my original post. I tried getting a minidump flushed to a pendrive via booting all usb drivers before controllers but it didn't stick.

It is seeing and reading the drive and the boot, but it's 7B'ing once it loads drivers.
My System SpecsSystem Spec
Reply

 0x7b - 0xC34 - Win7 Pro 32bit




Thread Tools





Similar help and support threads
Thread Forum
Dual Boot Win7 32bit and Win7 64bit on a second SSD drive
Hi folks. I have searched through the various threads that deal with this topic but have not seen anything that deals with this specifically. I have a custom built computer I put together last year. I installed Win7 32bit at the time because I didn't want to bite the bullet and reinstall...
Installation & Setup
Win7 32bit Home Premium to Win7 64bit Ultimate: Possible without Clean
I just bought a ThinkPad T400, and 8GB DDR3 upgrade kit. After first log on, I realized the Windows 7 is 32bit. How can I upgrade to Ultimate x64 instead? Thanks for your help.
Installation & Setup
Cannot read hdd from old desktop Win7 32bit on new laptop Win7 64bit
I have a new Toshiba Laptop (Win7 64bit CORE i3). I would like to run (via usb) and old hdd from my desktop which was 32bit Win7. I have the old hard drive in a SATA enclosure and running it via USB to my laptop. When I attempt to either copy or read the old hard drive I get a write protect error....
Hardware & Devices
Macrium Reflect: Restore Win7 32bit to Win7 64bit?
Just wondering if it would be possible to backup a Win7 32bit system, install a Win7 64bit system then restore the 32bit to the 64bit system? Simon
Backup and Restore
Win7 (32bit) to Win7 (64bit) upgrade install error
Hello I have purchased and downloaded both 32 bit and 64 bit Windows7 Professional (no CDs or media here only download version) I sucessfully upgraded from Vista 32 to Win7 32 Then I upgraded my hard disk (140Gb 500GB) and RAM (3GB to to 4GB) Now I would like to go from Win7 32bit...
Installation & Setup
Reinstall Win7 32bit to Win7 64bit /backup disc content
Hey, I purchased the Win 7 Pro Upgrade 32bit via digitalriver, but I've been doing some reseach and probably should have selected the 64bit version. - Any ideas how I can get the 64bit version? - For those who ordered the 32bit back-up disc kit for the extra $15 and have received it,...
Backup and Restore

Our Sites

Site Links

About Us

Find Us

Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

Designer Media Ltd

All times are GMT -5. The time now is 02:43.

Twitter Facebook Google+



Windows 7 Forums

Seven Forums Android App Seven Forums IOS App