BSOD while playing games

Welcome to the forums Thefus,

Code:

BugCheck 10D, {5, 0, 1202, fffffa80095ad4b0}

*** WARNING: Unable to verify timestamp for MijXfilt.sys
*** ERROR: Module load completed but symbols could not be loaded for MijXfilt.sys
Probably caused by : MijXfilt.sys ( MijXfilt+363a )

Code:

Usual causes:  Device driver, Memory

Code:

6: kd> lmvm MijXfilt
start             end                 module name
fffff880`0add1000 fffff880`0adf3000   MijXfilt T (no symbols)           
    Loaded symbol image file: MijXfilt.sys
    Image path: \SystemRoot\system32\DRIVERS\MijXfilt.sys
    Image name: MijXfilt.sys
    Timestamp:        Sat May 12 05:27:12 2012 (4FADE6A0)
    CheckSum:         00022009
    ImageSize:        00022000
    Translations:     0000.04b0 0000.04e4 0409.04b0 0409.04e4

The driver for the Wireless Xbox 360 Controller is rather outdated and causing problems, update it from here:

• MotioninJoy simulate Xbox 360 controller(virtual Xinput device) | MotioninJoy

Code:

6: kd> lmvm atikmdag
start             end                 module name
fffff880`04c5c000 fffff880`056e5000   atikmdag T (no symbols)           
    Loaded symbol image file: atikmdag.sys
    Image path: \SystemRoot\system32\DRIVERS\atikmdag.sys
    Image name: atikmdag.sys
    Timestamp:        Fri Sep 28 03:14:57 2012 (50650821)
    CheckSum:         00A3EAAC
    ImageSize:        00A89000
    Translations:     0000.04b0 0000.04e4 0409.04b0 0409.04e4

• AMD Graphics Drivers & Software

Your graphics driver is also rather outdated, it best to update the driver. Use the Automatic Detection program provided on the Support Page, and you may untick the option to install the Catalyst Control Centre.

X bluerobot please help me with my bsod problem. i posted it but noone replied to me
its similar to this persons bsod problem.. just dont know exactly what :/

Thanks BlueRobot. I installed the latest controller drivers, but it says my graphics card drivers are up to date and I cannot find a newer driver. Also, I've read problems about MotionInJoy causing Blue Screens due to drivers, so maybe that's what's going on, since I've started to use it for my games when I play.

Thefus said:

Thanks BlueRobot. I installed the latest controller drivers, but it says my graphics card drivers are up to date and I cannot find a newer driver. Also, I've read problems about MotionInJoy causing Blue Screens due to drivers, so maybe that's what's going on, since I've started to use it for my games when I play.

You'll have latest graphics drivers then, they just seemed a little outdated, and good job with updating the controller drivers. Post back if you have any more BSODs.

I got a blue screen while opening the launcher for Guild Wars 2. After that, my computer wouldn't start up properly and I needed to restore it to an earlier state. Some help would be nice, thanks. My info is attached.

Code:

BugCheck 10D, {5, 0, 1202, fffffa800c975010}

*** WARNING: Unable to verify timestamp for MijXfilt.sys
*** ERROR: Module load completed but symbols could not be loaded for MijXfilt.sys
Probably caused by : MijXfilt.sys ( MijXfilt+363a )

Code:

Usual causes:  Device driver, Memory

Code:

1: kd> lmvm MijXfilt
start             end                 module name
fffff880`0a611000 fffff880`0a633000   MijXfilt T (no symbols)           
    Loaded symbol image file: MijXfilt.sys
    Image path: \SystemRoot\system32\DRIVERS\MijXfilt.sys
    Image name: MijXfilt.sys
    Timestamp:        Sat May 12 05:27:12 2012 (4FADE6A0)
    CheckSum:         00022009
    ImageSize:        00022000
    Translations:     0000.04b0 0000.04e4 0409.04b0 0409.04e4

The same driver is being blamed as before, however, is most probably because the System Restore has restored you back to when the driver wasn't updated. Update this driver first.

The computer not being able boot properly, is commonly due to a either failing hard-drive or failing RAM.

• RAM - Test with Memtest86+

Run Memtest86+ for least 9-10 passes, and preferably overnight as it can take a while to fully complete.

Test each RAM stick individually, if an error is found then move the same RAM stick into the next DIMM slot and test again, if errors are found for the same RAM stick in every available slot then you have a faulty RAM module. On the other hand, if no errors are found in the next slot or the other slots for the same RAM module, then you have a faulty DIMM slot.

Test each RAM stick and every motherboard DIMM slot available.

Arc said:

No code has to be inserted here. It is a RAM, a bad RAM.

But if you have got a result like that:
No code has to be inserted here. It is a motherboard issue. The particular slot is bad.