|15 May 2013||#2|
fffff800`00b9b230 fffff880`01e2c210Unable to load image \SystemRoot\system32\DRIVERS\athurx.sys, Win32 error 0n2 *** WARNING: Unable to verify timestamp for athurx.sys *** ERROR: Module load completed but symbols could not be loaded for athurx.sys athurx+0x26210
Please update the driver from here: ATHEROS Wireless drivers for Windows
fffff800`00b9cc68 fffff880`03b479c2Unable to load image \SystemRoot\system32\DRIVERS\intelppm.sys, Win32 error 0n2 *** WARNING: Unable to verify timestamp for intelppm.sys *** ERROR: Module load completed but symbols could not be loaded for intelppm.sys intelppm+0x39c2
Please update the driver from here(it may be listed as a chip set driver): https://downloadcenter.intel.com/Default.aspx
fffff880`09fc5438 fffff880`049dde78Unable to load image \SystemRoot\system32\DRIVERS\nvlddmkm.sys, Win32 error 0n2 *** WARNING: Unable to verify timestamp for nvlddmkm.sys *** ERROR: Module load completed but symbols could not be loaded for nvlddmkm.sys nvlddmkm+0x197e78
FurMark: VGA Stress Test, Graphics Card and GPU Stability Test, Burn-in Test, OpenGL Benchmark and GPU Temperature | oZone3D.Net
- If you have more than one GPU, select Multi-GPU during setup
- In the Run mode box, select "Stability Test" and "Log GPU Temperature" (BurnIn test in newer versions).
Click "Go" to start the test
- Run the test until the GPU temperature maxes out - or until you start having problems (whichever comes first).
- Click "Quit" to exit
next OCCT, only follow the second part of this tutorial for a video memory stress test, and post the graphs that the test spits out, again assuming it does not cause a crash:
NVIDIA/AMD Video Card - Test with OCCT
Also run The system file checker I noticed alot of NTFS errors which could mean a corrupted file system:
Go to Start and type in "cmd.exe" (without the quotes)
At the top of the search box, right click on the cmd.exe and select "Run as adminstrator"
In the black window that opens, type "SFC.EXE /SCANNOW" (without the quotes) and press Enter.
If the results are anything other than "no violations found" run the command two more times
If after the third run there are still files that it can not fix run through this tutorial: SFC /SCANNOW : Run in Command Prompt at Boot
|My System Specs|
|16 May 2013||#3|
Updating Atheros AR9271 replaced my current TL-WN721N network driver and causes incredibly slow speeds and frequent connection disruption. Reverting the driver back to my TL-WN721N fixed this issue.
I could only find an Intel HD Graphics Driver for Pentium processors when searching for an i3 processor driver. I also tried the Intel Chipset Device Software (INF Update Utility), but it determined I already had the latest updates for this.
FurMark burn-in test showed a max 80C temp when stressing. Idle temp was around 48C.
OCCT GPU Memtest gives a "User Abort" while starting the test approx. 40 seconds after pressing "On". Tested 3 times.
System file checker running from Command Prompt at boot reported no integrity violations.
The most recent minidump may be due to GPU stress test using OCCT, although I am not sure.
|My System Specs|
|16 May 2013||#4|
OK had a look through your files and a couple of thoughts: It does seem that again the crash was caused by your graphics car/graphics card drivers how ever these errors can be caused by bad ram or a corrupted page file. So a few more things to try:
Reset your page file:
Use this technique to "reset" your pagefile:
a ) Go to Start...Run...and type in "sysdm.cpl" (without the quotes) and press Enter.
-Then click on the Advanced tab,
-then on the Performance Settings Button,
-then on the next Advanced tab,
-then on the Virtual Memory Change button.
b ) In this window, note down the current settings for your pagefile (so you can restore them later on).
-Then click on the "No paging file" radio button, and
- then on the "Set" button. Be sure, if you have multiple hard drives, that you ensure that the paging file is set to 0 on all of them.
-Click OK to exit the dialogs.
c ) Reboot (this will remove the pagefile from your system)
d ) Then go back in following the directions in step a ) and re-enter the settings that you wrote down in step b ). Follow the steps all the way through (and including) the reboot.
e ) Once you've rebooted this second time, go back in and check to make sure that the settings are as they're supposed to be.
RAM - Test with Memtest86+
Run some hard drive diagnostics to make sure you don't have a failing drive on your hands:
Hard Drive Diagnostic Procedure
If all of the scans come back clean and you still receive crashes try rolling back your driver to an earlier version, the current driver may contain bugs that could be causing the problem.
|My System Specs|
|07 Jun 2013||#9|
Upload your MSINFO32.nfo file. The previous one attached with your original post is incomplete.
|My System Specs|
|Similar help and support threads for2: Random BSODs, 0x3B, 0x1E, 0x17E|
|BSOD at random times. Error 0x3B / 0x1000007E / 0x1E||BSOD Help and Support|
|BSOD at random intervals, primarily 0x1e, 0x3b and 0x7e||BSOD Help and Support|
|BSODs; iTunes, Youtube, random; 0x1e, 0x3d...||BSOD Help and Support|
|BCCodes 0xa, 0x1e, 0x50 and 0x3b||BSOD Help and Support|
|Getting several BSODs 0x1E, 0xFE, 0x3b etc.||BSOD Help and Support|
|New installation - Win 7 (64 bit) - BSOD 0xa, 0x3b, 0x1e, etc||BSOD Help and Support|
|Random BSODs (mainly 0x3B)||BSOD Help and Support|
Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.
© Designer Media Ltd
All times are GMT -5. The time now is 15:24.