BSOD 1e

Page 4 of 4 FirstFirst ... 234

  1. Posts : 46
    Windows 7 Ultimate x64
    Thread Starter
       #31

    Okay so i got a new mem stick and i still get the bsod, what should i do now?
      My Computer


  2. Arc
    Posts : 35,373
    Microsoft Windows 10 Pro Insider Preview 64-bit
       #32

    Memtest on that new RAM module too, in all slots, one by one.
      My Computer


  3. Posts : 46
    Windows 7 Ultimate x64
    Thread Starter
       #33

    Now i ran the memtest86+ and so far i haven't gotten any red lines.
    So i guess the mem stick is good but the windows os is infected.
    Any further instructions?
      My Computer


  4. Arc
    Posts : 35,373
    Microsoft Windows 10 Pro Insider Preview 64-bit
       #34

    Have you tested it in all the slots? For how many passes?

    EDIT: The photo shows that the test is on zero pass right now.

    Sorry to say, but there is no "fix" button for a BSOD.

    EDIT AGAIN: I have asked others to guide you. I cannot provide the help that you are searching for.
      My Computer


  5. Posts : 24,479
    Windows 7 Ultimate X64 SP1
       #35

    Adafaka said:
    I just ran the memtest, it did 2 passes and it said that "hardware programs were found" and to contact the computer manufacture.And after the 2 passes it booted the pc to normal mode and a bsod appeared really fast and now i'm in safe mode. What now?
    Memtest86+ does not do that nor give messages. What did you run? Memtest need to run at least a full 8 passes and will take some hours. There is no quick fix and it has to be tracked down.

    If you're infected maybe a clean install is in order?
    Clean Install Windows 7
      My Computer


  6. Posts : 46
    Windows 7 Ultimate x64
    Thread Starter
       #36

    Hi, i canceled the memtest and somehow the automatic fix startup appeared and i selected that, then i selected the startup repair so i let it run for like 5 minutes and after that it asked for a reboot and it said that it fixed the problems.
    So i restarted and no bsod appeared and i'm posting from the computer that has/had the problem now.
    And now i did the command sfc /scannow in cmd and it also fixed some problems. And now it asks for a restart
    I will restart my pc and post if i still get bsod.
    If i don't get a bsod for a week i will mark this tread as solved
    Thank you for your assistance.
      My Computer


  7. Posts : 24,479
    Windows 7 Ultimate X64 SP1
       #37

    Reboot and run the sfc again to check all corrupt files have indeed been fixed.
      My Computer


  8. Posts : 21,004
    Desk1 7 Home Prem / Desk2 10 Pro / Main lap Asus ROG 10 Pro 2 laptop Toshiba 7 Pro Asus P2520 7 & 10
       #38

    Yes mate and in addition a chkdsk would not go amiss either Disk Check
      My Computer


  9. Posts : 46
    Windows 7 Ultimate x64
    Thread Starter
       #39

    I did the sfc /scannow command again and the same message appeared - in the picture below
    And i did the disk check, but i didn't see the results - because i was watching TV
    But however i took these snapshots - below..
      My Computer


  10. Posts : 21,004
    Desk1 7 Home Prem / Desk2 10 Pro / Main lap Asus ROG 10 Pro 2 laptop Toshiba 7 Pro Asus P2520 7 & 10
       #40

    Ok mate try this and see what comes up Finding Event Viewer & Viewing Chkdsk Results
      My Computer


 
Page 4 of 4 FirstFirst ... 234

Our Sites
Site Links
About Us
Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

© Designer Media Ltd
All times are GMT -5. The time now is 00:18.
Find Us