Windows 7 Forums

Welcome to Windows 7 Forums. Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks.


Windows 7: PFN_List BSOD less than 24hours after fresh install

06 Jul 2013   #21
mushibu09

Windows 7 Ultimate x64
 
 

Quote   Quote: Originally Posted by Layback Bear View Post
OP post #13

If these reading are correct your cards are running way to hot.
Yes Card does I have to use Asus GPU TTweak to set fan to 40% on start up to keep GPU idle temps below 55C and the boot process makes it heat to 78C it's old in a cramped Case that gets hot! (Zalman Z11) it's full in
there

this is the fan on auto after 30 minutes of watching Live TV on Windows Media Centre!


There is the new HDD that's old image! but it's cramped my PSU doesn't even fit in!

Quote:
Britton30

There is something wrong elsewhere too or the RAM would run at 1.5V. I tried to find a ref for your board but only found them for laptops.
I dont' kwow either i knwo the board has a history of blowing capacitors but mine are fine at moment they bulge but not blown, i think they are losing it's capacity the multi meter isn't keep climbing it's fluctuated up and down.


and alot of people has recommended them but I use Novatech.co.uk or Scan.co.uk

Thank you

Quote   Quote: Originally Posted by Arc View Post
Display driver is causing some issues here.
Code:
fffff880`091c6698  fffff880`04adc703Unable to load image \SystemRoot\system32\DRIVERS\atikmdag.sys, Win32 error 0n2
*** WARNING: Unable to verify timestamp for atikmdag.sys
*** ERROR: Module load completed but symbols could not be loaded for atikmdag.sys
 atikmdag+0xb0703
And it is old.
Code:
fffff880`04a2c000 fffff880`055df000   atikmdag T (no symbols)           
    Loaded symbol image file: atikmdag.sys
    Image path: \SystemRoot\system32\DRIVERS\atikmdag.sys
    Image name: atikmdag.sys
    Timestamp:        Sat Nov 17 01:48:02 2012 (50A69F7A)
    CheckSum:         00B65E3C
    ImageSize:        00BB3000
    Translations:     0000.04b0 0000.04e4 0409.04b0 0409.04e4
Update your ATI/AMD display driver.
You can get it from the link in our forum, Latest AMD Catalyst Video Driver for Windows 7, or you may go to AMD Graphics Driver and Software and opt for Automatically Detect and Install the appropriate driver for your card.


During installation, you may opt for advanced installation, and install the display driver only, not the Catalyst Control Center.

Is the computer hot? Report us the heat of the computer after a couple of hours of your normal usage. Upload a screenshot of the summery tab of Speccy.
I have installed driver your way not a problem yet, but it's early days, no ballon saying AMD recovered so big thumbs up there!

Thank you


My System SpecsSystem Spec
.
06 Jul 2013   #22
ICIT2LOL

Desk1 7 Home Prem / Desk2 10 Pro / Main lap Asus ROG 10 Pro 2 laptop Toshiba 7 Pro Asus P2520 7 & 10
 
 

Quote   Quote: Originally Posted by mushibu09 View Post
Im not doing that! how stupid! and dangerous! I have electrocuted my self before messing with PSU and Vintage TV Tubes! not doing it again sorry! it doesn't even say what to do after then! either so I am s'posed to turn it on with out motherboard then what? make sure it all powers up, well yes it does te only one that doesn't is a hard drive because it's not plugged in!

sorry, I just want to knwo what caused the BSOD!!
Look mate I don't like being called stupid for one thing and another I have been messing with electronics since I was ten and yes I have had a few whacks, form all sorts of sources TV's car and motor cycle ignition circuits radios and wall sockets etc etc . As Britton said electrocuted means DEAD so unless you are calling from behind the white light then I shall assume you mean that you have received a few shocks in the past.
I do know what I am talking about here being a registered nurse of 40+ years who has on quite a few occasions had to apply direct electrical stimuli to the individual who has collapsed and am more than aware of what charges and voltages that cardio version involves and what energy levels are required to stop a persons cardiac electrical function in those instances. So stupid I am definitely not.

The voltages you would have been dealing with in the PSU cabling would not have given you a shock unless you were stupid enough to stand bare foot in a puddle of water and stick the leads on your tongue and that would not have involved the energy levels I spoke of a while ago.

If you had you had taken the PSU apart and played with the large caps inside then you may have had cause for concern and the possibility of a fatal shock so don't give me that rubbish!!
Just as well I didn't send any further info on testing 3,5 and 12v at the cable ends or I might have got a real mouthful.
I am very disappointed by your reaction and I hope you can find someone who can help you out as it would appear that I do not have enough sense to do that.
As for me I shall take no further part in solving your problem!!
My System SpecsSystem Spec
06 Jul 2013   #23
mushibu09

Windows 7 Ultimate x64
 
 

The Capacitors are on motherboard not PSU and they are bulging not burst! they are losing their ability to hold power, and you reaction is just as bad! i dont' mess with something that i can't afford to replace and if there is even a 1% chance of it going wrong I am not doing it I dont' have the money for a new PSU at a kilowatt sorry.

the 3.5 and 12V are all coming out with in range 3.296v and 11.857v
My System SpecsSystem Spec
.

06 Jul 2013   #24
ICIT2LOL

Desk1 7 Home Prem / Desk2 10 Pro / Main lap Asus ROG 10 Pro 2 laptop Toshiba 7 Pro Asus P2520 7 & 10
 
 

Quote   Quote: Originally Posted by mushibu09 View Post
The Capacitors are on motherboard not PSU and they are bulging not burst! they are losing their ability to hold power, and you reaction is just as bad! i dont' mess with something that i can't afford to replace and if there is even a 1% chance of it going wrong I am not doing it I dont' have the money for a new PSU at a kilowatt sorry.

the 3.5 and 12V are all coming out with in range 3.296v and 11.857v
Well you obviously did not take in what I said, and I am originally from England and therefore to me calling a member (me) stupid is not good form my friend. I think that you should choose your words very carefully because it is language like that that will not get you anywhere, besides I would hazard a guess that you would not walk up to someone in the street and call them stupid if they proffered advice that did not sit well with you or would you?? .

I said nothing about caps on the board or did you for that matter in the first instance. I simply said that you ought to test the PSU as it is often the most common component in a machine to go bad, and that a simple non dangerous test - as if I were likely to advise you to do something very risky - would soon show if you were getting enough (non lethal) volts to power the machine.

Now the volts as a matter of fact are on the fair to low side for the +12v rail and the 3.3V rail seem ok. What the 5v was you don't mention but the main volts of concern of course is the 12v supply.

I would be very concerned to see any caps bulging and in fact am wondering if they are not already dead or very close to it. Just as matter of curiosity just how long do the caps last after you have replaced them if they are the ones that are replaced? As for replacing them why not try the solid Japanese type as the ones you quoted are in fact not working for you, as I think the heat you mentioned will have direct effect on those components.
Now I am not suggesting for one moment that you are but the caps you have replaced are the right way round if electrolytic ones/ Because the wrong way round they will work for a very short period before they eventually stop working or worse explode!
I am sorry that you find yourself in a financial situation whereby you just cannot go out and buy what is needed - most of us have been down that track and it is very frutrating I know. But I would guess that to replace the board caps with Jap ones is not going to be cheap either as it involves a fair amount of disassembly and work to do that - been there done that and don't like it.
My System SpecsSystem Spec
06 Jul 2013   #25
Layback Bear

Windows 7 Pro. 64/SP-1
 
 

mushibu09 I have read through this thread 3 times. Because I'm one of the stupid ones.
Have a nice day.
My System SpecsSystem Spec
07 Jul 2013   #26
Arc

Microsoft Community Contributor Award Recipient

Microsoft Windows 10 Pro Insider Preview 64-bit
 
 

Quote   Quote: Originally Posted by mushibu09 View Post

I have installed driver your way not a problem yet, but it's early days, no ballon saying AMD recovered so big thumbs up there!

Thank you
If more balloons are coming, let us know. Balloons are not good things to have.
My System SpecsSystem Spec
07 Jul 2013   #27
mushibu09

Windows 7 Ultimate x64
 
 

The 5V is the 4/8 Pin CPU plug? if SO I use the 8 pin that is provided.

the stupid is rhetorical (or what ever the other word is like that)

Capacitors Didn't replace i don't feel compitant to replace them my self as there are so many layers in motherboard and I don't want to short it out my nearest computer store (private small business) said he won't do it either because it works.
Quote:
If it isn't broken, Don't Fix It!
the capacitors don't keep climbing when using a multimeter so I think they are dying but I can't remember. if they explode the Electrolytic fluid shorts out the whole motherboard right?

What brand of Japanese ones? I was going to get EXACTLY The Same Capacitors, but I don't know I'm going AMD again! Intel is expensive, and I should have stayed AMD

Also If i went amd and plugged HDD into amd nd booted windows would it work or would i have to reinstall windows? and i Think i will have to uninstall ALL drivers before doing so?
My System SpecsSystem Spec
07 Jul 2013   #28
mushibu09

Windows 7 Ultimate x64
 
 

Quote   Quote: Originally Posted by Arc View Post
Quote   Quote: Originally Posted by mushibu09 View Post

I have installed driver your way not a problem yet, but it's early days, no ballon saying AMD recovered so big thumbs up there!

Thank you
If more balloons are coming, let us know. Balloons are not good things to have.
I've not had the error yet bit now PC just freezes when playing online videos BBC iPlayer, and watchseries.lt but sometimes it unfreezes and others it doesn't im uts going to get a bassic Graphics card a basic nVidia one keep this old one for back up.

Thank you anyway. oh two more dmp files if you want them?
My System SpecsSystem Spec
07 Jul 2013   #29
Arc

Microsoft Community Contributor Award Recipient

Microsoft Windows 10 Pro Insider Preview 64-bit
 
 

I would like to see those, only to see if any hint of graphics related elements are present there or not.
My System SpecsSystem Spec
07 Jul 2013   #30
mushibu09

Windows 7 Ultimate x64
 
 

the dmp files was saved in the C:\ Directory not in the %root%\minidumps

Thank you.
My System SpecsSystem Spec
Reply

 PFN_List BSOD less than 24hours after fresh install




Thread Tools Search this Thread
Search this Thread:

Advanced Search




Similar help and support threads
Thread Forum
BSOD's PFN_list, Power_Management, Memory_Management.
I'm having some BSOD's since maybe 1-3 months now. It first started with the Power_Management BSOD a month or maybe more before which was occuring once a day. Now, since a week or so the Memory_Management BSOD is occurring as well. Still 1 BSOD a day, Memory_management more often. Today I checked...
BSOD Help and Support
BSOD playing Guild Wars 2, recent SSD install and fresh install of W7
I just added a new SSD drive and installed a fresh copy of Win 7 Enterprise. I have had a previous driver issue with this system in the past. The amazing people on this site helped me work it out. Now for the life I just can't seem to sort it out again myself this time. I ran and uploaded the...
BSOD Help and Support
BSOD on fresh install when install updates, misc error codes
My system info is in my profile, installing Windows 7 x64 Ultimate Retail. Attached is all of the report info. I have no idea what is going on. Whenever I try to install all of the Windows updates it blue screens. Then it will reboot, try to apply the updates, and blue screen again. I've run...
BSOD Help and Support
pfn_list corrupt BSOD
Hello, this is my first post. This is a bit long-winded :shock: Note: I have never successfully installed w7 with the video card plugged in. Before the partition screen in setup, it freezes, or pops up with a missing resources error. I pull the card, and install windows with my onboard ...
BSOD Help and Support
BSoD install windows7 professional 32bit PFN_List error
Hi everybody, i really need some help, i was trying to put windows7 pro 32bit on my gf's desktop she was using vista, and it was working just fine only really slow and i wanted to wipe it clean, i reformatted the partition and tried installing, it worked fine until about 25% and it blue screened...
BSOD Help and Support
Random BSOD - Fresh install, fresh system
Hi. I have installed a whole new windows 7 pro x64. My new mobo an ASus p5e3 pro along with new ram pc12800 gskill 2x2 ddr3 (running in 1066mhz due to my q6600) Everythingi s running perfectly...except some random BSOD. 4 total this week. I have posted a pack of dump file in here, the last 4...
BSOD Help and Support


Our Sites

Site Links

About Us

Find Us

Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

Designer Media Ltd

All times are GMT -5. The time now is 07:53.

Twitter Facebook Google+



Windows 7 Forums

Seven Forums Android App Seven Forums IOS App