Windows 7 Forums
Welcome to Windows 7 Forums. Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks.


Windows 7: BSOD - MEMORY MANAGEMENT and PAGE FAULT IN NON PAGED AREA

04 Nov 2013   #1

Windows 7 Professional x64
 
 
BSOD - MEMORY MANAGEMENT and PAGE FAULT IN NON PAGED AREA

All,

I built my PC in 2010. Ever since I have been having intermittent BSOD problems. I've found that if I put the computer to sleep instead of shutting down, when it boots stable, it will remain stable. Otherwise I have BSOD crashes 5-20 minutes after booting. I've run memtest86+ after crashes and had it report errors, but if I remove the RAM, re-insert it, and run memtest, no errors will be reported. It also typically remains stable if I boot after inserting the RAM. Anyway, this is getting to be a pain and I'm trying to work something out. I posted before, and the last piece of advice I received was as follows:

"That is not unusual, electronics are just that way, when memtest86+ shows errors it means there is a problem. Even if it doesn't show any errors the run before and the run after.
An error with 2X4GB installed and then no errors with 1X2GB installed, usually indicates a timing and/or voltage adjustment is needed.

It is still possible that the RAM is faulty, let's try some adjustments and see if it will run stable.

CPUZ is showing your CR at 1T, go to BIOS and select 2T again, save and exit BIOS.
Then check CPUZ Memory tab and see if it says CR 2T.

Go to DRAM timings and change 'cycle time (tRAS)' to 25, this will be the 4th item in BIOS -DDR3 Timings Items.
When changed it should read, for the first 4 timings:
9
9
9
25

Bump your CPU NB voltage to 1.240v or as close as you can get it to that number.
Save and exit BIOS.

Then run memtest86+ again, both RAM cards installed, for a minimum of 8 passes, best to run overnight."

Having done this, memtest reported erros. Should I just pick up some new sticks of RAM, or do you think this is something else?

Thanks for all the help,

Tom



Attached Files
File Type: zip weirdtommyro.zip (2.79 MB, 12 views)
My System SpecsSystem Spec
.

05 Nov 2013   #2
Arc

Microsoft Community Contributor Award Recipient

Windows 7 Home Premium 64 Bit SP 1
 
 

Upload your MSINFO32.nfo file.
  1. Click on the start button
  2. Type "msinfo32" (without quotes) in the search bar of the start menu, click the resulting link. It will open the System Information window.
  3. File>Save. In the "File Name" filed, put "MSINFO32" (without Quote), give the save location to desktop, and click the "save" button.
  4. Give the time for processing, it will save a .nfo file on your desktop.
  5. Zip it, and upload it following the instruction.
______________________________________________________________________________________________
Code:
*******************************************************************************
*                                                                             *
*                        Bugcheck Analysis                                    *
*                                                                             *
*******************************************************************************

Use !analyze -v to get detailed debugging information.

BugCheck F4, {3, fffffa8004764b30, fffffa8004764e10, fffff800037cb0d0}

----- ETW minidump data unavailable-----
Probably caused by : wininit.exe

Followup: MachineOwner
---------
My System SpecsSystem Spec
05 Nov 2013   #3
Microsoft MVP

Windows 7 Ultimate X64 SP1
 
 

Did you check the RAM sticks individually in other slots? If you have the RAM specs set properly, then I suspect it is faulty.
My System SpecsSystem Spec
.


16 Nov 2013   #4

Windows 7 Professional x64
 
 

Arc,

Attached is the .zip file. Sorry for the delay, and thanks again for all of the help.


Attached Files
File Type: zip MSINFO32.zip (133.4 KB, 2 views)
My System SpecsSystem Spec
17 Nov 2013   #5
Arc

Microsoft Community Contributor Award Recipient

Windows 7 Home Premium 64 Bit SP 1
 
 

Test your HDD using Data Lifeguard Diagnostic for Windows. Let us know the results.

Also post a screenshot of your HDD using CrystalDiskInfo - Software - Crystal Dew World.
My System SpecsSystem Spec
10 Dec 2013   #6

Windows 7 Professional x64
 
 

The results of both quick test and extended test were "PASS" Attached is the screenshot from crystaldiskinfo. Thank you for your help.


Attached Images
 
My System SpecsSystem Spec
11 Dec 2013   #7
Arc

Microsoft Community Contributor Award Recipient

Windows 7 Home Premium 64 Bit SP 1
 
 

As your last BSOD report is of 3 weeks ago, I think it is better to wait.
My System SpecsSystem Spec
Reply

 BSOD - MEMORY MANAGEMENT and PAGE FAULT IN NON PAGED AREA




Thread Tools



Similar help and support threads for2: BSOD - MEMORY MANAGEMENT and PAGE FAULT IN NON PAGED AREA
Thread Forum
BSOD: Page fault in non paged area and Memory Management error. BSOD Help and Support
Solved Memory Management/Page fault in nonpaged area BSOD BSOD Help and Support
Solved Windows 7 x64 BSOD memory management and page fault in non paged area BSOD Help and Support
Windows 7Memory Management and Page Fault In Non Paged Area BSOD Help and Support
BSOD - Memory Management and Page Fault In Non Paged Area BSOD Help and Support

Our Sites

Site Links

About Us

Find Us

Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

Designer Media Ltd

All times are GMT -5. The time now is 11:15 PM.
Twitter Facebook Google+



Windows 7 Forums

Seven Forums Android App Seven Forums IOS App
  

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33