Windows 7 Forums

Welcome to Windows 7 Forums. Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks.


Windows 7: "PFN_LIST_CORRUPT" BSOD on new build

28 Nov 2013   #31
x BlueRobot

 

I don't think it's a stack overflow, something has most likely gone wrong with some form of Synchronization. It's difficult to say with the little information provided from a Minidump.

Code:
.trap fffff800`044c1e70
NOTE: The trap frame does not contain all registers.
Some register values may be zeroed or incorrect.
rax=0000000000000007 rbx=0000000000000000 rcx=0000000000000043
rdx=f88008d876500006 rsi=0000000000000000 rdi=0000000000000000
rip=fffff80002e98698 rsp=000000000000d824 rbp=0000000000000000
 r8=0000000000000021  r9=0000000000000007 r10=00000000000000fe
r11=0000000000000000 r12=0000000000000000 r13=0000000000000000
r14=0000000000000000 r15=0000000000000000
iopl=0         nv up ei pl zr na po nc
nt!KiIpiSendRequest+0x128:
fffff800`02e98698 0044898b        add     byte ptr [rcx+rcx*4-75h],al ds:00000000`000000da=??
Code:
0: kd> !irql
Debugger saved IRQL for processor 0x0 -- 12 (SYNCH_LEVEL)
Code:
0: kd> !ipi
IPI State for Processor 0
    TargetCount          0  PacketBarrier        0  IpiFrozen     0 [Running]
All I can gather is that Processor 0, sent out a IPI for some reason.

Could you please check this directory:

Code:
C:\Windows\MEMORY.DMP
Compress the file and then place into a zipped folder, and upload to a free file sharing site like Dropbox or Skydrive.


My System SpecsSystem Spec
.
28 Nov 2013   #32
agentsmith24

Windows 7 Ultimate 64 Bit
 
 

My System SpecsSystem Spec
29 Nov 2013   #33
x BlueRobot

 

Code:
BugCheck 1A, {411, fffff68000019ca0, 9450000316cd9884, fffff6800001a101}

Probably caused by : ntkrnlmp.exe ( nt! ?? ::FNODOBFM::`string'+6071 )
This bugcheck indicates that a PTE has become corrupt, parameter 2 contains the address of the corrupt PTE.

Code:
7: kd> !pte fffff68000019ca0
                                           VA 0000000003394000
PXE at FFFFF6FB7DBED000    PPE at FFFFF6FB7DA00000    PDE at FFFFF6FB400000C8    PTE at FFFFF68000019CA0
contains 1530000363B52867  contains 03B0000363B53867  contains 08F0000317CFB867  contains 9450000316CD9884
pfn 363b52    ---DA--UWEV  pfn 363b53    ---DA--UWEV  pfn 317cfb    ---DA--UWEV  not valid
                                                                                  Transition: 316cd9
                                                                                  Protect: 4 - ReadWrite
Code:
7: kd> knL
 # Child-SP          RetAddr           Call Site
00 fffff880`08f6c788 fffff800`02ea4c4d nt!KeBugCheckEx
01 fffff880`08f6c790 fffff800`02ef9281 nt! ?? ::FNODOBFM::`string'+0x6071
02 fffff880`08f6c7e0 fffff800`02ee5c8f nt!MiResolveTransitionFault+0x381
03 fffff880`08f6c870 fffff800`02ed5179 nt!MiDispatchFault+0x95f
04 fffff880`08f6c980 fffff800`02ec6cee nt!MmAccessFault+0x359
05 fffff880`08f6cae0 000007fe`ec6110d0 nt!KiPageFault+0x16e
06 00000000`1faaecf8 00000000`00000000 0x000007fe`ec6110d0
Let's establish a few things, the page of paged pool isn't resident in physical memory, thus why the PTE is marked as invalid. A Page Fault happens when this page is referenced and brought into physical memory.
Run Memtest86+ for least 9-10 passes, and preferably overnight as it can take a while to fully complete.

Test each RAM stick individually, if an error is found then move the same RAM stick into the next DIMM slot and test again, if errors are found for the same RAM stick in every available slot then you have a faulty RAM module. On the other hand, if no errors are found in the next slot or the other slots for the same RAM module, then you have a faulty DIMM slot.

Test each RAM stick and every motherboard DIMM slot available.

Quote   Quote: Originally Posted by Arc View Post
testSlot1Slot2
RAM1ErrorError
RAM2GoodGood
It is a RAM, a bad RAM.

But if you have got a result like that:
testSlot1Slot2
RAM1ErrorGood
RAM2ErrorGood
It is a motherboard issue. The particular slot is bad.
My System SpecsSystem Spec
.

01 Dec 2013   #34
agentsmith24

Windows 7 Ultimate 64 Bit
 
 

This is gonna take a while, about 2 hours per pass...
My System SpecsSystem Spec
02 Dec 2013   #35
x BlueRobot

 

You could try one stick at a time, instead of doing 16GB all at once.
My System SpecsSystem Spec
02 Dec 2013   #36
agentsmith24

Windows 7 Ultimate 64 Bit
 
 

I am. First stick went 10 passes with no errors, 2nd one is on 6 with no errors so far
My System SpecsSystem Spec
03 Dec 2013   #37
agentsmith24

Windows 7 Ultimate 64 Bit
 
 

Both sticks went 10-11 passes in Slot 1 with 0 errors. Stick #2 in slot 2 just failed with 4 errrors. Attached is a photo of the results. I'm running Stick #1 in slot 2 now.
My System SpecsSystem Spec
04 Dec 2013   #38
agentsmith24

Windows 7 Ultimate 64 Bit
 
 

Stick #1 in slot 2 succeeded through 13 passes with no errors. So the only one that failed was the above post. What does that mean?
My System SpecsSystem Spec
04 Dec 2013   #39
x BlueRobot

 

It may be acute error in the RAM stick, are all the RAM matched I.e same timings and MHz (clockspeed)?
My System SpecsSystem Spec
04 Dec 2013   #40
agentsmith24

Windows 7 Ultimate 64 Bit
 
 

They were bought as a matched pair so I would think so
My System SpecsSystem Spec
Reply

 "PFN_LIST_CORRUPT" BSOD on new build




Thread Tools Search this Thread
Search this Thread:

Advanced Search




Similar help and support threads
Thread Forum
New Build, repeated "Page fault in nonpaged area" BSOD 0x00000050
I built this computer a few weeks again and have been getting a periodic (every 2-3 days) BSOD. I ran Memtest as was recommended to those with similar problems; it cycled through four times without detecting any errors. I need to figure out which piece of hardware (presumably) is the problem so I...
BSOD Help and Support
BSOD happened every 1 hour and Error "pfn_list_corrupt "
Hi all, My laptop compaq suddenly got BSOD error yesterday and caused me a lot of headache. I googled and did all of solutions like : Safe mode, last good condition ,check disk,scan driver,...restore computer many time but BSOD still happens ...except openning my laptop to see RAM ... using Win 7...
BSOD Help and Support
BSOD every few hours: mostly "STOP: 0x00000F4", "c00021a" & "c0000135"
Hi everyone! Yesterday my HP laptop (Windows 7) started getting BSOD with various types of errors (mostly "STOP: 0x00000F4", "STOP: 0x0000007A", "c00021a" and one "missing %hs, c0000135"). Most of the time it restarts without any issues and works fine right after the BSOD and then an hour or two...
BSOD Help and Support
Need to add "TASKBARS" (MSese for "Launchpads", "Docks" NOT "Toolbars"
My office just upgraded, and I can no longer use Windows XP. On this system, I was able to add a separate taskbar to facilitate quick access to commonly-browsed folder locations on our vast network, and another one expedited the launching of useful programs and lists. Each task on each taskbar...
General Discussion
Random BSoDs ("PFN_LIST_CORRUPT")
There doesn't seem to be any rhyme or reason to them, sometimes I can go a week without a problem, other times it'll be as often as one a day. It doesn't seem to matter what programs I'm running as it's happened while playing Starcraft 2 and also when just browsing the web. Not really sure what...
BSOD Help and Support
Unpredictable BSOD, "PFN_LIST_CORRUPT"
Recently, after installing an extra 8GB of ram (I made sure it was the same freq and CAS timings before I got it) and a new SSD to use for boot/system files, I've been getting random BSODs (the latest was "PFN_LIST_CORRUPT", unsure about the earlier ones). I first ran memtest86+ fully twice, and it...
BSOD Help and Support


Our Sites

Site Links

About Us

Find Us

Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

Designer Media Ltd

All times are GMT -5. The time now is 07:54.

Twitter Facebook Google+



Windows 7 Forums

Seven Forums Android App Seven Forums IOS App