Windows 7 Forums

Welcome to Windows 7 Forums. Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks.


Windows 7: BSOD, Regular Bugcheck error

29 Dec 2013   #31
mrd156

Windows 7 Pro (64bit)
 
 

New grab all as below;
Attachment 299253

Something I did note was when I have a graphics card connected to the second port I will not physically see a blue screen display. The system would freeze screens go blank then you here the system beep. Windows recovery shows then you see the windows crashed pop-up after log-in.

Here is a link for the motherboard,
GIGABYTE - Motherboard - Socket 1150 - GA-B85M-D3H (rev. 1.x)

These are the details on the expantion slots;
1 x PCI Express x16 slot, running at x16 (PCIEX16)
* For optimum performance, if only one PCI Express graphics card is to be installed, be sure to install it in the PCIEX16 slot.
(The PCIEX16 slot conforms to PCI Express 3.0 standard.)
1 x PCI Express x16 slot, running at x4 (PCIEX4)
2 x PCI slots


On a higher specified motherboard, GIGABYTE - Motherboard - Socket 1150 - GA-Z87X-D3H (rev. 1.x)
I see it says to do this * When installing a x8 or above card in the PCIEX4 slot, make sure to set PCIE Slot Configuration in BIOS Setup to x4.

In the BIOS of my system there is only one option I see; I have changed between the Gen modes and it does not seem to make a difference (still get BSOD when connected to second port, also have tried both graphics cards have the same BSOD with either connected). In the system block diagram is shows two PCI bus' one for the main x16 graphics port and a second x4 bus with the x16 size graphics port and two PCI ports shared. I have been using one of the PCI ports for an Intel network adapter.

Miscellaneous Settings
PEG Gen3 Slot Configuration
Allows you to set the operation mode of the PCI Express slots to Gen 1, Gen 2, or Gen 3. Actual operation
mode is subject to the hardware specification of each slot. For example, the PCI Express x1 slots can
support up to Gen 2 mode only. Auto lets the BIOS automatically configure this setting. (Default: Auto)

Here is the motherboard layout;
Attachment 299254


My System SpecsSystem Spec
.
29 Dec 2013   #32
mrd156

Windows 7 Pro (64bit)
 
 

The second PCI-e x16 size (x4 speed) only has the pins in the port for x4 connection. I had only noted this yesterday.

The graphics card supports this type of connection PCI Express 2.0 x16 (Compatible with 1.1)

Here is an image of the motherboard so you can see what I mean.
Attachment 299257
My System SpecsSystem Spec
03 Jan 2014   #33
YoYo155

Windows 10
 
 

Did you?


Quote   Quote: Originally Posted by YoYo155 View Post
Hi mrd156, if you don't mind please Zip & upload the Kernel dump as I want to take a look
at the memory usage as sometimes 0xF4 can be caused due to a depletion in resources.

Please upload the Kernel dump file using Dropbox or Skydrive, the file is located in the Windows directory
and is usually a few hundred Megabytes in size.
Code:
C:\Windows\MEMORY.dmp
My System SpecsSystem Spec
.

Reply

 BSOD, Regular Bugcheck error




Thread Tools Search this Thread
Search this Thread:

Advanced Search




Similar help and support threads
Thread Forum
Very regular BSOD. Most often error 0x000001E
Hello guys. I've been getting BSOD for a looong time now, and finally decided to seek some help! This bluescreen mostly happens when im playing games. Please do guide me if you need more informations! VERY much appreciated.
BSOD Help and Support
BSOD on start, Startup Repair: Unknown Bugcheck: Bugcheck 3d
We've been getting a BSOD on one of our computers on startup recently. The exact message the BSOD gives varies but often mentions atapi.sys. Having done extensive research we've come to the conclusion that it could be a rootkit or it could be the fact that we have Daemon Tools installed on the...
BSOD Help and Support
BSOD error: The bugcheck was: 0x0000007f
Original title: The computer has rebooted from a bugcheck. The bugcheck was: 0x0000007f (0x0000000000000008, 0x0000000080050033, 0x00000000000406f8, 0xfffff88004f7a1ed). hi all! Been getting a lot BSODīs in the past few days. All my drivers and bios are up to date. Yesterday the same BSOD...
BSOD Help and Support
Regular BSOD (multiple error codes)
Hello, NOTE: Sorry if my English fails, I'm dutch and only 13. NOTE: I'm going on holiday for some days and probably read this again on sunday. For about 4 months I receive BSOD and it's getting worse and worse. Last week i've got 3 of them a day. Error codes: 0x0000003b (2 times)...
BSOD Help and Support
BSOD, Bugcheck error
So, I have recently upgraded my computer, and the whole thing is brand new, new motherboard, cpu, memory, harddrive, and video card. Since getting my computer up and running, I keep getting BSOD's, and when I check the event logs, I get this error, Log Name: System Source:...
BSOD Help and Support
BSOD BugCheck Error 0x0000001e
Hello! - I am using Win 7 Professional 64 bits (OEM) - This computer is just 1 month old. - I have reinstall win7 once 2 weeks ago Problems 1. When i start up my system (from turning off), I will get "Kernel-Event Tracing" error with message " "Microsoft Security Essentials OOBE"...
BSOD Help and Support


Our Sites

Site Links

About Us

Find Us

Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

Đ Designer Media Ltd

All times are GMT -5. The time now is 01:55.

Twitter Facebook Google+



Windows 7 Forums

Seven Forums Android App Seven Forums IOS App