Windows 7 Forums

Welcome to Windows 7 Forums. Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks.


Windows 7: PAGE_FAULT_IN_NON_PAGED_AREA, random BSODs

01 Mar 2014   #11
anthonylert

Windows 7 Professional x64
 
 

BSOD again. This time UNEXPECTED_KERNEL_MODE_TRAP, 0x0000007F. I'm beginning to suspect my processor might be having issues.

Attached dump as per usual.


My System SpecsSystem Spec
.
01 Mar 2014   #12
Arc

Microsoft Community Contributor Award Recipient

Microsoft Windows 10 Pro Insider Preview 64-bit
 
 

Stress test the Graphics Card using Furmark.
Video Card - Stress Test with Furmark

Test your RAM modules for possible errors.
How to Test and Diagnose RAM Issues with Memtest86+
Run memtest for at least 8 passes, preferably overnight.

If it start showing errors/red lines, stop testing. A single error is enough to determine that something is going bad there.

If it does not show any error, enable Driver Verifier to monitor the drivers.
Driver Verifier - Enable and Disable
Run Driver Verifier for 24 hours or the occurrence of the next crash, whichever is earlier.

information   Information
Why Driver Verifier:
It puts a stress on the drivers, ans so it makes the unstable drivers crash. Hopefully the driver that crashes is recorded in the memory dump.

How Can we know that DV is enabled:
It will make the system bit of slow, laggy.

warning   Warning
Before enabling DV, make it sure that you have earlier System restore points made in your computer. You can check it easily by using CCleaner looking at Tools > System Restore.

If there is no points, make a System Restore Point manually before enabling DV.

Tip   Tip

Let us know the results, with the subsequent crash dumps, if any.
_______________________________________________________
Code:
BugCheck 7F, {8, 80050033, 406f8, fffff800038b9ac7}

Probably caused by : memory_corruption

Followup: memory_corruption
-----------------------------------------------------
BugCheck 3B, {c0000005, fffff96000127814, fffff8800dd8db20, 0}

Probably caused by : win32k.sys ( win32k!NtUserGetThreadState+b4 )

Followup: MachineOwner
---------
My System SpecsSystem Spec
02 Mar 2014   #13
anthonylert

Windows 7 Professional x64
 
 

Did 9 passes on MemTest, no errors. Did FurMark test as instructed by tutorial, no red lines or obvious graphical artifacts, ran test until temps evened out at 75-76C. Only noticable thing was what appeared to be the test attempting to insert white text at the bottom of the screen, about where you'd see subtitles in a movie. They were illegible.

Attached log from burn-in test, just in case it is helpful. Will enable Driver Verifier tonight.
My System SpecsSystem Spec
.

04 Mar 2014   #14
anthonylert

Windows 7 Professional x64
 
 

Another bluescreen while I was preparing to start Driver Verification. Posting dump.
My System SpecsSystem Spec
04 Mar 2014   #15
Arc

Microsoft Community Contributor Award Recipient

Microsoft Windows 10 Pro Insider Preview 64-bit
 
 

The BSOD indicates to Intel USB3 driver.
Code:
*** WARNING: Unable to verify timestamp for iusb3hub.sys
*** ERROR: Module load completed but symbols could not be loaded for iusb3hub.sys
*******************************************************************************
*                                                                             *
*                        Bugcheck Analysis                                    *
*                                                                             *
*******************************************************************************

Use !analyze -v to get detailed debugging information.

BugCheck 1000007E, {ffffffffc0000005, fffff88005849a3b, fffff88005fb5908, fffff88005fb5160}

Probably caused by : iusb3hub.sys ( iusb3hub+49a3b )

Followup: MachineOwner
---------
But it is the latest one as per ECS Web Site > Z87H3-A2X EXTREME (V1.0)

So it may not be the real reason.

Upload the list of all the third party drivers Using NirSoft DriverView :
  • Download and execute Driverview
  • View > Hide Microsoft Drivers
  • Edit > Select all
  • File > Save Selected Items
  • In the Save dialog, Set the path to desktop, Put "Driverview" in the name field, and save.
  • Zip the .txt file and upload it.
Also let us know what are the USB devices you have attached to the system.
My System SpecsSystem Spec
04 Mar 2014   #16
anthonylert

Windows 7 Professional x64
 
 

Enabled driver verifier, immediate BSODs before getting to desktop. Went to Safe Mode to use SF. Attached dumps.
My System SpecsSystem Spec
04 Mar 2014   #17
anthonylert

Windows 7 Professional x64
 
 

Attached driverview as requested.

Current USB attachments are as follows:
*****
brother DCP-7060D MFC All-in-One Laser Printer

StarTech 35FCREADBK3 USB 2.0 Internal Card Reader (attached to USB header on motherboard)

CM Storm Sentinel Advance 2 Mouse

Microsoft Comfort Curve Keyboard 2000

Kensington 33902 Bluetooth USB Micro Adapter

Logitech 980186-0403 Silver USB Microphone
My System SpecsSystem Spec
04 Mar 2014   #18
Arc

Microsoft Community Contributor Award Recipient

Microsoft Windows 10 Pro Insider Preview 64-bit
 
 

You havent done the driverview properly. It shows only one driver, whereas there are a lot.

Have another try.

But some important result came out from the latest crash dump. The MotioninJoy simulate Xbox 360 controller (virtual Xinput device) is causing the BSOD.
Code:
BugCheck C2, {9b, 1, 20, fffff88005a393eb}

*** WARNING: Unable to verify timestamp for MijXfilt.sys
*** ERROR: Module load completed but symbols could not be loaded for MijXfilt.sys
Probably caused by : MijXfilt.sys ( MijXfilt+1c3eb )

Followup: MachineOwner
---------
It is a very common scenario with the driver version that you have installed. Uninstall it, and install an earlier version of the driver from Playstation 3 controller(Dualshcok 3 or Sixaxis) driver for windows | MotioninJoy

Let us know the result.
My System SpecsSystem Spec
04 Mar 2014   #19
anthonylert

Windows 7 Professional x64
 
 

Added proper Driver View text. Added latest BSOD that occurred prior to rolling back MotionInJoy driver.
My System SpecsSystem Spec
04 Mar 2014   #20
Arc

Microsoft Community Contributor Award Recipient

Microsoft Windows 10 Pro Insider Preview 64-bit
 
 

It is strange that how frequently the bugcheck codes and probable causes are changing.

It is the display driver this time.
Code:
BugCheck 1E, {0, 0, 0, 0}

*** WARNING: Unable to verify timestamp for nvlddmkm.sys
*** ERROR: Module load completed but symbols could not be loaded for nvlddmkm.sys

Probably caused by : nvlddmkm.sys ( nvlddmkm+27e1b3 )

Followup: MachineOwner
---------
Install the http://www.nvidia.com/object/win8-wi...ql-driver.html only, as a test.
  • Uninstall All nvidia items in Control Panel > Programs and features
    • 3D Vision Control Driver
    • 3D Vision Driver
    • Graphics Driver
    • HD Audio Driver
    • PhysX
    • nvidia Update
    • GeForce Xperience
    (Are you using nvidia chipset drivers? If so, dont uninstall anything other than those are listed).
  • Now follow Drivers - Clean Left over Files after Uninstalling
  • Download 314.22 WHQL. While installing, Select Custom (Advanced) install. In the next page, follow this settings:

But the frequent changing pattern is not feeling good at all. Test your RAM modules for possible errors.
How to Test and Diagnose RAM Issues with Memtest86+
Run memtest for at least 8 passes, preferably overnight.

If it start showing errors/red lines, stop testing. A single error is enough to determine that something is going bad there.


Let us know the results.
My System SpecsSystem Spec
Reply

 PAGE_FAULT_IN_NON_PAGED_AREA, random BSODs




Thread Tools Search this Thread
Search this Thread:

Advanced Search




Similar help and support threads
Thread Forum
BSOD Page_Fault_In_Non_Paged_area Stop 0x00000050 ( cdd.dll )
Hello! My PC turned 4x already since yesterday a blue screen saying page fault in nonpaged area. I'm clueless and not so pro in checking dump files, but i a average user in knowledge about computers. My PC Specs are: Processor:Intel Core i5-4440 3.1 GHz Motherboard:Intel DB85FL Motherboard...
BSOD Help and Support
Constant BSODs, usually Page_Fault_in_Non_paged_Area
I've updated motherboard and GPU drivers, don't get any video errors, and have run the Microsoft AND Memtest86 memory testers. Will run memtest86 again while I'm at work (9AM-4PM EST). Also ran Malwarebytes, combofix, and a few others. Dump files are attached. Hope you can help. :cool:
BSOD Help and Support
Bsod page_fault_in_non_paged_area (0x50)
This BSOD has started since this Wednesday, I think. Im not sure what is causing the BSOD. Things I have tried : chkdsk /f /r --> nothing wrong; sfc /SCANNOW --> Nothing wrong... Disabled Norton (Using the Disable Autoprotection) and System Restore to a point on 10.10.2012. Also I tried to (Boot...
BSOD Help and Support
Multiple BSODs (Memory_Management, Page_Fault_In_Non_Paged_Area)
Hello guys. For the past few days, I have been getting multiple BSODs on my custom built computer (I built it about 3-4 months ago, first time builder). It started when my AMD graphics driver crashed while I was playing Borderlands 2. I have tried re-installing multiple drivers, including the AMD...
BSOD Help and Support
BSOD after factory Reinstall Page_fault_in_non_paged_area
Okay, im new here at the sevenforums. so please stay with with me lol. my computer wouldnt start one day, (yesterday) and i eventually was led into HP's recovery application, after windows wasnt able to restore my computer. Now, after all was said and done, i reinstalled windows 7 from im...
BSOD Help and Support
atikmdag.sys BSOD, page_fault_in_non_paged_area
I have been having random BSOD's ever since I bought this laptop about a year ago. First is the page_fault_in_non_paged_area BSOD, this one happens randomly no matter what I am doing and makes operating my system impossible, forcing me to system restore to the original drivers that came when...
BSOD Help and Support


Our Sites

Site Links

About Us

Find Us

Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

Designer Media Ltd

All times are GMT -5. The time now is 15:27.

Twitter Facebook Google+



Windows 7 Forums

Seven Forums Android App Seven Forums IOS App