Windows 7 Forums

Welcome to Windows 7 Forums. Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks.


Windows 7: BSOD after computer sits idle

17 Jun 2014   #1
clydefrawg

Windows 7 Ultimate x64
 
 
BSOD after computer sits idle

About 5 days ago I noticed my computer would restart itself at some point during the day. I caught it in the act once, and it was a BSOD. I didn't have a chance to catch the type of error. My best guess on the timing is about 2 hours of idling.

I haven't made any hardware changes recently. I've also noticed during this time span that my computer's boot time has gotten a bit longer. It'll sit for a while on a black screen with my cursor on it, after the Starting Windows 7 screen and before my login screen pops up. Don't know if related.

Microsoft Security Essentials and MalwareBytes haven't picked up anything in my multiple scans. I've tried multiple error tests and have come up with nothing. Attached is the .zip file.


My System SpecsSystem Spec
.
18 Jun 2014   #2
HarriePateman

Windows 7 Ultimate 64-bit
 
 

I have had a look at the Dumps, and i believe its caused by "Fastfat.sys"

Quote:
This issue may occur if either of the following conditions exist:
The Fastfat.sys file is damaged or missing.
The RAM in your computer is damaged or is not installed correctly.
My System SpecsSystem Spec
18 Jun 2014   #3
PeregrineX

Windows 7 Ultimate X64
 
 

Hello and welcome to SevenForums!

KERNEL_DATA_INPAGE_ERROR (7a_c0000185) seems to be the error here:

Code:
*******************************************************************************
*                                                                             *
*                        Bugcheck Analysis                                    *
*                                                                             *
*******************************************************************************

KERNEL_DATA_INPAGE_ERROR (7a)
The requested page of kernel data could not be read in.  Typically caused by
a bad block in the paging file or disk controller error. Also see
KERNEL_STACK_INPAGE_ERROR.
If the error status is 0xC000000E, 0xC000009C, 0xC000009D or 0xC0000185,
it means the disk subsystem has experienced a failure.
If the error status is 0xC000009A, then it means the request failed because
a filesystem failed to make forward progress.
Arguments:
Arg1: fffff6fc40008730, lock type that was held (value 1,2,3, or PTE address)
Arg2: ffffffffc0000185, error status (normally i/o status code)
Arg3: 00000000866ea860, current process (virtual address for lock type 3, or PTE)
Arg4: fffff880010e6b9c, virtual address that could not be in-paged (or PTE contents if arg1 is a PTE address)

Debugging Details:
------------------

TRIAGER: Could not open triage file : e:\dump_analysis\program\triage\modclass.ini, error 2

ERROR_CODE: (NTSTATUS) 0xc0000185 - The I/O device reported an I/O error.

DISK_HARDWARE_ERROR: There was error with disk hardware

BUGCHECK_STR:  0x7a_c0000185

CUSTOMER_CRASH_COUNT:  1

DEFAULT_BUCKET_ID:  CODE_CORRUPTION

PROCESS_NAME:  System

CURRENT_IRQL:  0

TRAP_FRAME:  fffff88002fe7a20 -- (.trap 0xfffff88002fe7a20)
NOTE: The trap frame does not contain all registers.
Some register values may be zeroed or incorrect.
rax=fffff880010e42a0 rbx=0000000000000000 rcx=fffffa8004a9d060
rdx=fffffa800883c620 rsi=0000000000000000 rdi=0000000000000000
rip=fffff880010e6b9c rsp=fffff88002fe7bb8 rbp=fffff8a013735790
 r8=0000000000000007  r9=fffffa8004a9d1b0 r10=0000000000000000
r11=fffffa800883c6f0 r12=0000000000000000 r13=0000000000000000
r14=0000000000000000 r15=0000000000000000
iopl=0         nv up ei ng nz ac po cy
PCIIDEX!GenPnpPdoQueryDeviceRelations:
fffff880`010e6b9c 0000            add     byte ptr [rax],al ds:fffff880`010e42a0=??
Resetting default scope

LAST_CONTROL_TRANSFER:  from fffff80003145752 to fffff800030d2bc0

STACK_TEXT:  
fffff880`02fe7708 fffff800`03145752 : 00000000`0000007a fffff6fc`40008730 ffffffff`c0000185 00000000`866ea860 : nt!KeBugCheckEx
fffff880`02fe7710 fffff800`030f991f : fffffa80`04708010 fffff880`02fe7880 fffff800`0330d540 fffffa80`04708010 : nt! ?? ::FNODOBFM::`string'+0x36c1a
fffff880`02fe77f0 fffff800`030e01b9 : 00000000`00000000 00000000`00000008 ffffffff`ffffffff fffff880`010cc100 : nt!MiIssueHardFault+0x28b
fffff880`02fe78c0 fffff800`030d0cee : 00000000`00000008 fffff880`010e6b9c 00000000`50656400 fffffa80`0883c6f0 : nt!MmAccessFault+0x1399
fffff880`02fe7a20 fffff880`010e6b9c : fffff880`010e7ada fffffa80`04ae61b0 00000000`000007ff 00000000`00000001 : nt!KiPageFault+0x16e
fffff880`02fe7bb8 fffff880`010e7ada : fffffa80`04ae61b0 00000000`000007ff 00000000`00000001 fffffa80`04a9f050 : PCIIDEX!GenPnpPdoQueryDeviceRelations
fffff880`02fe7bc0 fffff880`010c8efe : 00000000`00000001 00000000`00000004 fffff800`03278200 fffffa80`04a9f1a0 : PCIIDEX!PciIdeDispatchPnp+0x22
fffff880`02fe7bf0 fffff800`033c9c93 : 00000000`00000001 00000000`00000004 00000000`00000000 fffff880`02fe7c50 : ataport!ChannelQueryBusRelation+0xfa
fffff880`02fe7c40 fffff800`030dc261 : fffff800`034eaa00 fffff800`03278201 fffffa80`03ce5b00 fffffa80`03ce5b50 : nt!IopProcessWorkItem+0x23
fffff880`02fe7c70 fffff800`0336e73a : eefff4ff`f7bbff1f fffffa80`03ce5b50 00000000`00000080 fffffa80`03c709e0 : nt!ExpWorkerThread+0x111
fffff880`02fe7d00 fffff800`030c38e6 : fffff880`009eb180 fffffa80`03ce5b50 fffff880`009f5f40 3ffffff7`2ffdf5bf : nt!PspSystemThreadStartup+0x5a
fffff880`02fe7d40 00000000`00000000 : 00000000`00000000 00000000`00000000 00000000`00000000 00000000`00000000 : nt!KxStartSystemThread+0x16


STACK_COMMAND:  kb

MODULE_NAME: memory_corruption

IMAGE_NAME:  memory_corruption

FOLLOWUP_NAME:  memory_corruption

DEBUG_FLR_IMAGE_TIMESTAMP:  0

MEMORY_CORRUPTOR:  LARGE

FAILURE_BUCKET_ID:  X64_MEMORY_CORRUPTION_LARGE

BUCKET_ID:  X64_MEMORY_CORRUPTION_LARGE

Followup: memory_corruption
---------
Run an SFC /SCANNOW command and inform us with the results.

The error subset "c000185" could also mean there's an issue with your hard drive cabling. Check to see if all the ports to your hard drive are installed correctly, pushed in all the way, and free of any dust.

Best of luck,

PeregrineX

EDIT: Dangit, HLPTech ninja'd me. He seems to be more experienced than I am, but I believe either one of the two of us could be right. I'll look into this some more, and check back on you.
My System SpecsSystem Spec
.

18 Jun 2014   #4
clydefrawg

Windows 7 Ultimate x64
 
 

I ran the sfc /scannow command- "Windows Resource Protection did not find any integrity violations."

I opened up the bottom of my computer just to take a quick look to see if anything looked loose. Everything seemed in place to me, but then again I'm not sure what and where I should be looking. I'm running on an HP dv7, for the record.
My System SpecsSystem Spec
18 Jun 2014   #5
clydefrawg

Windows 7 Ultimate x64
 
 

Just now I was running a MSE scan in the background while attempting to open up a Word document off of my flash drive. Word was unresponsive, and then I got the BSOD. I've attached a picture.
My System SpecsSystem Spec
18 Jun 2014   #6
PeregrineX

Windows 7 Ultimate X64
 
 

Quote   Quote: Originally Posted by clydefrawg View Post
Just now I was running a MSE scan in the background while attempting to open up a Word document off of my flash drive. Word was unresponsive, and then I got the BSOD. I've attached a picture.
OK, this BSOD gives us more information.

The 0x7a error KERNEL_DATA_INPAGE_ERROR with parameter 2 being 0xc00000185 means that there is defective cabling of your SCSI (or, your SATA HDD) device, or two devices are using the same interrupt request (IRQ) at the same time.

Other common causes are faulty hardware, failing RAM, or a virus infection, however these are less common than the causes above.

Let's start simple: run a Memtest86+ test by downloading the software off of this website: www.memtest.org. This will test your RAM for any errors or corruption.

Please inform us of the results.

Best of luck,

PeregrineX
My System SpecsSystem Spec
18 Jun 2014   #7
clydefrawg

Windows 7 Ultimate x64
 
 

Ran the Memtest86+ for one pass, here's a photo from that.
My System SpecsSystem Spec
18 Jun 2014   #8
PeregrineX

Windows 7 Ultimate X64
 
 

Quote   Quote: Originally Posted by clydefrawg View Post
Ran the Memtest86+ for one pass, here's a photo from that.
Good, there are no errors. Your RAM is fine.

It is nighttime in my part of the world, so I best be off to bed. I will return to look at this issue tomorrow.

Good luck!
My System SpecsSystem Spec
18 Jun 2014   #9
Boozad

W7 Pro x64 SP1 | W10 Pro IP x64 | W8.1 Pro x64 VM | Linux Mint VM
 
 

MemTest needs to run for at least 8 passes for conclusive results. 1 pass is nowhere near enough to determine if RAM is faulty or not. Run it again for at least 8 passes.

Code:
*******************************************************************************
*                                                                             *
*                        Bugcheck Analysis                                    *
*                                                                             *
*******************************************************************************

KERNEL_DATA_INPAGE_ERROR (7a)
The requested page of kernel data could not be read in.  Typically caused by
a bad block in the paging file or disk controller error. Also see
KERNEL_STACK_INPAGE_ERROR.
If the error status is 0xC000000E, 0xC000009C, 0xC000009D or 0xC0000185,
it means the disk subsystem has experienced a failure.
If the error status is 0xC000009A, then it means the request failed because
a filesystem failed to make forward progress.
Arguments:
Arg1: fffff6fc40008730, lock type that was held (value 1,2,3, or PTE address)
Arg2: ffffffffc0000185, error status (normally i/o status code)
Arg3: 00000000866ea860, current process (virtual address for lock type 3, or PTE)
Arg4: fffff880010e6b9c, virtual address that could not be in-paged (or PTE contents if arg1 is a PTE address)

Debugging Details:
------------------


ERROR_CODE: (NTSTATUS) 0xc0000185 - The I/O device reported an I/O error.

DISK_HARDWARE_ERROR: There was error with disk hardware

BUGCHECK_STR:  0x7a_c0000185

CUSTOMER_CRASH_COUNT:  1

DEFAULT_BUCKET_ID:  CODE_CORRUPTION
Run MemTest86+ to analyse your RAM. RAM - Test with Memtest86+

Note   Note
MemTest86+ needs to be run for at least 8 passes for conclusive results. Set it running before you go to bed and leave it overnight. We're looking for zero errors here. Even a single error will indicate RAM failure.


Run SeaTools to check the integrity of your HDD. SeaTools for DOS and Windows - How to Use

Run chkdsk. Disk Check

Report back with the results.
My System SpecsSystem Spec
19 Jun 2014   #10
clydefrawg

Windows 7 Ultimate x64
 
 

Ran 8 sweeps with Memtest last night, no errors. I attached a picture.

Ran chkdsk C: /r and found bad clusters. Filename it gave me was for a sound effect for one of my Steam games.

Ran Seatools under Windows. Short Generic Test: FAIL. Perhaps a dumb question, but does it stop scanning once it fails? Progress bar hasn't moved for a while and no further information given.

Does this mean my HD is nearing the end of its life?
My System SpecsSystem Spec
Reply

 BSOD after computer sits idle




Thread Tools Search this Thread
Search this Thread:

Advanced Search




Similar help and support threads
Thread Forum
BSOD only when PC sits idle for random time.
Hi, I reformatted so I lost the logs for now, but it keeps happening when I let the pc sit idle (e.g. overnight). I set the power options to performance mode - still had the issue Set the hard disk to never turn off - still had the issue. Any ideas?
BSOD Help and Support
Freeze after computer sits idle
What's happening is when I leave the computer and come back an hour or more later, I will be able to move my mouse cursor around but I cannot bring up anything on the desktop (taskbar which is hidden, right click menu or windows key menu), and after I try to do any of these tasks or I move the...
BSOD Help and Support
BSOD after computer sits for few hours or 1 day less
Small Desktop Lenovo M92p (2988) First thx for volunteering your time to help all us... This is a computer that is NOT a server despite the computer name but a desktop I setup in our small 5 person volunteer office to have a machine to place files on and I created mapped share drives for all...
BSOD Help and Support
BSOD when computer sits for a while - Think it might be Wireless mouse
Hello, I've got an interesting problem that has recently cropped up. I like to have my gaming PC hooked up to my television with an HDMI output. I have a 700W Power Supply, and it is running a Radeon HD 6770. I bought a cheap wireless mouse and keyboard to help me reduce the clutter in the...
BSOD Help and Support
BSOD - Crashes while computer idle/not idle (Unpredictable)
Windows 7 Enterprise 64bit Clean installation to windows 7 from Windows XP professional Hardware 18 months old OS installed 2 weeks ago I am currently facing the lovely BSOD error. The computer was recently upgraded from windows XP to Windows 7 enterprise 64bit , this was a fresh...
BSOD Help and Support
BSOD when computer sits idle
So I'm running an older computer. Started with vista, went to xp, then upgraded to Win 7 64x after the upgrade advisor said everything would be ok. Immediatly I started getting BSOD and after reading many message boards I decided to swap out the ram with new ram. This didn't seem to resolve the...
BSOD Help and Support


Our Sites

Site Links

About Us

Find Us

Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

Designer Media Ltd

All times are GMT -5. The time now is 23:30.

Twitter Facebook Google+



Windows 7 Forums

Seven Forums Android App Seven Forums IOS App