Windows 7 Forums

Welcome to Windows 7 Forums. Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks.


Windows 7: New build BSOD 0x0000124 Blue screen crash - DM log uploaded!

06 Jul 2014   #21
Paulgo253

Windows 7 Professional 64 bit
 
 

Many thanks for your advice. - The hardware monitor in the bios shows the vcore voltage at 1.128v, the 3.3v at 3.37, the 5v at 5.12v and the 12v at 12.091 which is confusing! CPU temp is 48 and MB temp is 26.

The only real difference in the set up is that for Windows 7 I've used a re-formatted hard drive which is actually exactly the same spec as my old drive running XP (this drive was not present when I installed windows 7).

thanks again!


My System SpecsSystem Spec
.
06 Jul 2014   #22
Paulgo253

Windows 7 Professional 64 bit
 
 

Just managed to get speccy and HW to run under windows 7. They showed a 12v reading of around 7.5v and the CPU was running at around 60! Rebooted an it was around 49 but steadilly rising!
My System SpecsSystem Spec
06 Jul 2014   #23
essenbe

Windows 7 Enterprise X64/Windows 10 Enterprise X64/Windows 10 Pro X64/Linux Mint
 
 

The numbers in BIOS are usually more correct. Software readings are notoriously wrong, that's why they should be used a guidelines and not absolute numbers. It is also a possibility you have some bad sensors on your board, that's what software reads. It's not my money, but if it were me, I would buy a new quality PSU first. That is most likely needed, and removes that as a concern for your problems. Plus, you can use you graphics card again.
My System SpecsSystem Spec
.

07 Jul 2014   #24
Paulgo253

Windows 7 Professional 64 bit
 
 

Thanks again for all your suggestions guys. No real update as I've not been able to change any hardware - but the pc is now crash as soon as Windows 7 loads from the welcome screen - and this was from completely cold both this morning and again tonight.

Looking at the BIOS monitor the voltages are still looking right but the CPU temp is sitting steady at around 52, rising quickly from about 34 at start up.CPU fab speed is 1480 rpm - would a new cooler fan help?

I still don't understand why the pc will boot using the XP hard drive and run fine, but not the 7 drive. Check the hard drive twice for bad sectors etc and both times been clean. I guess the error messages don't point to the new hard drive but could that be the culprit???....
My System SpecsSystem Spec
07 Jul 2014   #25
essenbe

Windows 7 Enterprise X64/Windows 10 Enterprise X64/Windows 10 Pro X64/Linux Mint
 
 

Yes it could. You can run the manufacturer of the hard drive's diagnostic test and see. You can also, disconnect the XP hard drive an run the windows start up repair. Startup Repair

The temps for your CPU are high, but not dangerously high. They may get dangerously high if put under a lot of stress, but are not that way now. The problem could be the air flow through the case, the cooler or the thermal paste used. Personally, I never use the stock coolers, as they are not very good and usually are pretty loud as well.

Seatools for Dos, run the short and long test http://www.seagate.com/support/inter...ls-dos-master/
My System SpecsSystem Spec
07 Jul 2014   #26
Paulgo253

Windows 7 Professional 64 bit
 
 

Cheers - all the diagnostics I did were the windows 7 internal ones. Bit of a daft question but as I can't get the windows 7 hard drive to run at the moment can I do the test booting on the XP drive wit the 7 drive showing as just an additional drive?

One last thing - I dint install any motherboard drivers as the new 7 install seemed to be running ok - should I have?Thanks!
My System SpecsSystem Spec
07 Jul 2014   #27
essenbe

Windows 7 Enterprise X64/Windows 10 Enterprise X64/Windows 10 Pro X64/Linux Mint
 
 

I would at least install the chipset drivers, then when you are able to boot, go to device manager and see what yellow icons you see, Those are devices with no drivers. Install drivers for them. I know you will need the USB 3.0 drivers and probably the Lan Driver.

Both tests I linked to are bootable, you boot into the test not the OS. The start up repair you can boot into the installation DVD, about the 2nd or 3rd screen you will see fix my computer in the bottom right. Click that. The tutorial will explain that. The Seagate for dos is much the same way, You can boot into the CD or whatever media you use, and run the test from there. It will give better results when you are not booted into the drive you are testing.
My System SpecsSystem Spec
07 Jul 2014   #28
Paulgo253

Windows 7 Professional 64 bit
 
 

Great will give that a go and thanks again for your help here! The pc has been running just the Bios and the monitor temp is still 54, but then it has no load as you say! I think a new cooler would e a good idea especially as I have no thermal paste. The only driver I noticed with a yellow ! when I could access the 7 drive was something like Terredo Tunneling psuedo something - don't if that's important!
My System SpecsSystem Spec
07 Jul 2014   #29
essenbe

Windows 7 Enterprise X64/Windows 10 Enterprise X64/Windows 10 Pro X64/Linux Mint
 
 

Thermal paste is important, and the right amount too. It is relatively cheap and any top brand is good. You can also get a decent cooler for not much money. I use the Noctua brand, but most of the Artic brands are good too and cost around $10 in the US. Most any of the top brands will do you fine and there is honestly little difference in them, but I never use the pre applied paste on any cooler. But, you have to clean off the old paste and apply new paste. When you get ready, just let me know, and I'll tell you how.
My System SpecsSystem Spec
08 Jul 2014   #30
Paulgo253

Windows 7 Professional 64 bit
 
 

Hi the new drive passed both long and short seagate tests. Just found one thing tho. The system has been crashing more or less seconds after the desktop loaded after the welcome screen. During this time I had the graphics card still attached tot he board but not connected up. I've just removed the card entirely and the system hasn't crashed yet so I've been able to install the motherboard drivers. All was going well until I tried to install the graphics and the screen suddenly went blank - pc continued to run the finally rebooted - I'm assuming this is not good!! This seems to point to something graphics related as there have been instances before when it wouldn't display anything when coming out of hibernation
!
My System SpecsSystem Spec
Reply

 New build BSOD 0x0000124 Blue screen crash - DM log uploaded!




Thread Tools Search this Thread
Search this Thread:

Advanced Search




Similar help and support threads
Thread Forum
Blue Screen (SF diagnostic folder uploaded in the post)
Hello, my computer crashes very often (say once a day) since, I would say, a couple of weeks. I always get the following error: Problem signature: Problem Event Name: BlueScreen OS Version: 6.1.7601.2.1.0.768.3 Locale ID: 1033 I have followed the BSOD instructions and uploaded the files...
BSOD Help and Support
N/build all games crash to desktop or give me a blue screen
Hey guys, Got a new home build Core I5 3rd gen at 4.4GB 8gb RAM, 120 SSD with the OS, 2GB HDD for anything else, ATI 7970. Win 7 home 64 bit. When I play games, I can play for a while, then I get Game name has stopped working, or a BSOD, he's the zipped fold as requested, thanks everyone.
BSOD Help and Support
BSOD Blue Screen Crash
Is Windows 7 Home Premium x64 It's the original installed OS Full Retail version The age of system is 1 year The OS is 1 year old and i didn't re-installed it. It crashes whenever I play a game or I watch a movie.
BSOD Help and Support
BSOD ...blue screen crash ...
these crashes are happened so frequently ....please help OS : windows 7 ultimate x64 cpu: intel core2due E7500 2.93 GHz memory : 4 GB graphic cards : Nvidia Gforce 9500 GT hard drive : 500 GB dmp files in the attachment thank you for your time
BSOD Help and Support
BSOD Crash!Blue screen occured while installing windows!!
HI,guys! Im new to computers,when i got the BSOD,i just installed the windows again and agin!But it turns out, doesnt work at all!Sometimes,when i was installing,it popped up a BSOD,and i need to try again and again until the installation is done.So im thinking this is a hardware issue!! I...
BSOD Help and Support
Blue screen error every morning(uploaded DMP files)
EDIT: Took it back to where i bought it and they changed my Motherboard to a GA-P55-USB3 and the problem seems to have gone. They weren't sure if it was a faulty motherboard or compatibility issues. They ran something called a burning test and they were getting similar messages got to do with...
BSOD Help and Support


Our Sites

Site Links

About Us

Find Us

Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

Designer Media Ltd

All times are GMT -5. The time now is 17:25.

Twitter Facebook Google+



Windows 7 Forums

Seven Forums Android App Seven Forums IOS App