BSOD Apparantly random

You're welcome, as always Arc.

Just some things I noticed in Speccy. They may or may not be causing a problem. I'm not sure how any of them would cause a video card problem.

1. Bitdefender and Windows Defender are both running.

2. You are also using AVG Tune up

3. You are using Team Viewer at this time.

3. You have a Asus P9X79-WS Quad channel with 3 of the 8 ram slots used. It should be 2, 4, 6, or 8 slots used.

4. Your ssd in hook to Sata II at 3.0 gb. instead of Sata III at 6.0 gb.

With all that information we still need to know what power supply you are using.
You state that it is a custom build so if you could put your power supply in your system specs.

You need at a minimum a 550W quality power supply with two 6 pin connectors for the video card.

have you had any more BSODs? If you have upload the same file again. Did you reinstall the driver like the tutorial said and run Furmark again? Set the custom fan profile?

Same thing again Video TDR

Code:

BugCheck 116, {fffffa8013fc4010, fffff8800ff7851c, ffffffffc000009a, 4}
*** WARNING: Unable to verify timestamp for nvlddmkm.sys
*** ERROR: Module load completed but symbols could not be loaded for nvlddmkm.sys
Probably caused by : nvlddmkm.sys ( nvlddmkm+91951c )
Followup: MachineOwner
 
nvlddmkm
start             end                 module name
fffff880`0f65f000 fffff880`10333000   nvlddmkm T (no symbols)           
    Loaded symbol image file: nvlddmkm.sys
    Image path: \SystemRoot\system32\DRIVERS\nvlddmkm.sys
    Image name: nvlddmkm.sys
    Timestamp:        Sat Sep 13 14:59:50 2014 (5414A236)
    CheckSum:         00C8E3A6
    ImageSize:        00CD4000
    Translations:     0000.04b0 0000.04e4 0409.04b0 0409.04e4

I'm not really sure reinstalling the drivers would help or not. If you do, try a different driver and use the same procedure. NVIDIA Drivers - Avoid Problems

Also, you may check and see if you have the latest DirectX How to install the latest version of DirectX

Also please go to device manager and expand graphics adapters and post a screenshot of the wholw device manager. This will tell you how to post a screenshot.
Screenshots and Files - Upload and Post in Seven Forums

Unless you are overheating, the problem is your Card, Motherboard or PSU. You may try putting it in a different slot on your motherboard, just to see.

Owen27 said:

I installed the driver as recommended in the tutorial. As soon as I went to run Furmark, Blue screen.

Rebooted and ran it again. Got to the 13 Minute mark and it was at 89 Degrees. Went to take a picture and Blue Screened again.

Dump files attached.

Though it is not an even regularity, but it is there. BSOD during Furmark. That is the point.

Your GPU is failing to handle a stress. Sometimes it cannot, sometimes it can, but not for a long time, and sometimes it manages the stress for a fairly good time. Overall, it has started failing.

Still, a good firs step will be to try the GPU in a different PCIe slot, as essenbe suggested. You have alternative slots ....

Attachment 337564

If the issue continues even in the other slot, you will have to apply a different card, at least on a test basis.

I hoovered out the PC. (Paying particular attention to in and around the graphics card)

I also pushed it in, to ensure it was fully connected. No crashes since then.

It's still early days and it could very well happen again. At the very least it seems to of improved the stability. Or it could be a coincidence.