Windows 7 Forums

Welcome to Windows 7 Forums. Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks.


Windows 7: BSOD CRITICAL_OBJECT_TERMINATION (f4)

19 Mar 2015   #1
Ivanissevich

Windows 7 Ultimate x64
 
 
BSOD CRITICAL_OBJECT_TERMINATION (f4)

Been having infrequent bsod's since start 2014. got really bad now, once/ twice a day.

Tested Ram with memtest for 14 passes, tested hd with seagate tools, all reported thumbs up.
Also did a chkdsk c: /r without any errors.
Installed the latest drivers from the manufacture, didn't solve it,
installed latest drivers from intel. Didn't solve it.
Swapped ram to different slot.
Reinstalled windows with latest drivers from manufacture, problem continued.*
Swapped out the RAM for new stick**, and here I am asking more learned people then myself for a hand.

The first minidump happened at * stge of troubleshooting, the last 2 minidump happened at **

All help apreciated

PS. didn't have the foresight to conserve old minidumps, they got erased when I reinstalled windows.

PPS. tried to install Win7 in UEFI mode, but it kept hanging at "starting windows" screen, despite trying several workarounds I found on the net. Just gave up and activated CSM and installed in bios mode. PC originally came with windows 8, and that windows would install in UEFI mode without a hitch, but I think thats a matter for another thread.


My System SpecsSystem Spec
.
19 Mar 2015   #2
Ivanissevich

Windows 7 Ultimate x64
 
 

just realized audio and card reader drivers went installed, just installed them from the manufactures page (lenovo), activated driver verifier as suggested in other posts to make sure its not a driver problem.
My System SpecsSystem Spec
20 Mar 2015   #3
essenbe

Windows 7 Enterprise X64/Windows 10 Enterprise X64/Windows 10 Pro X64/Linux Mint
 
 

Hello, Ivanissevich. I will try to help you with this. I read your troubleshooting steps you have taken, but from reading the dumps it appears to be a hard drive error.

Code:
KERNEL_DATA_INPAGE_ERROR (7a)
The requested page of kernel data could not be read in.  Typically caused by
a bad block in the paging file or disk controller error. Also see
KERNEL_STACK_INPAGE_ERROR.
If the error status is 0xC000000E, 0xC000009C, 0xC000009D or 0xC0000185,
it means the disk subsystem has experienced a failure.
If the error status is 0xC000009A, then it means the request failed because
a filesystem failed to make forward progress.
Arguments:
Arg1: fffff6fc40009c98, lock type that was held (value 1,2,3, or PTE address)
Arg2: ffffffffc000000e, error status (normally i/o status code)
Arg3: 0000000121130860, current process (virtual address for lock type 3, or PTE)
Arg4: fffff880013939a0, virtual address that could not be in-paged (or PTE contents if arg1 is a PTE address)
Code:
ERROR_CODE: (NTSTATUS) 0xc000000e - A device which does not exist was specified.
DISK_HARDWARE_ERROR: There was error with disk hardware

The other 2 were this

Code:
CRITICAL_OBJECT_TERMINATION (f4)
A process or thread crucial to system operation has unexpectedly exited or been
terminated.
Several processes and threads are necessary for the operation of the
system; when they are terminated (for any reason), the system can no
longer function.
Arguments:
Arg1: 0000000000000003, Process
Arg2: fffffa8005503b30, Terminating object
Arg3: fffffa8005503e10, Process image file name
Arg4: fffff80002de3db0, Explanatory message (ascii)
Stop Code f4 is almost always a hard drive error

Code:
!process fffffa8005503b30 3
GetPointerFromAddress: unable to read from fffff80002d11000
PROCESS fffffa8005503b30
    SessionId: none  Cid: 0170    Peb: 7fffffd5000  ParentCid: 0168
    DirBase: 18e79000  ObjectTable: fffff8a000a2fd80  HandleCount: <Data Not Accessible>
    Image: csrss.exe
    VadRoot fffffa80055008f0 Vads 87 Clone 0 Private 465. Modified 283. Locked 0.
    DeviceMap fffff8a000008d80
    Token                             fffff8a000a2f060
    ReadMemory error: Cannot get nt!KeMaximumIncrement value.

If you would, please make sure your machine is set to create Small Memory Dumps Dump Files - Configure Windows to Create on BSOD

Please fill out your System Specs

information   Information
Your System Specs will help us to help you, and doing it in this manner will make them available to all helpers in every post and keep us from hunting for them. We ask that you fill them out in as much detail as possible including Desktop or Laptop, Model number if it is an OEM computer and all components with the Manufacturer and Model number if possible.

If you will go to your last post and click the 'System Specs' in the bottom left of the post, you will find a link to update your system specs. Please fill those out in as much detail as possible, making sure to click save at the bottom of the page. If you would like to know what we would like, you can click 'My System Specs' at the bottom left of this post to see mine. If you do not know what your components are, this will help you accomplish this task. System Info - See Your System Specs

Also, I know you have already run it, but I would like you to run Seatools for DOS again. Run the long and the short test. SeaTools for DOS and Windows - How to Use

Also run Check Disk Disk Check
My System SpecsSystem Spec
.

20 Mar 2015   #4
Ivanissevich

Windows 7 Ultimate x64
 
 

Sorry about the sys specs, filled them in with my personal pc, however this BSOD pertains to a friend's pc, his specs are:

Lenovo C240 10113
Intel Celeron 847
Motherboard chipset Intel NM70
Kingston DDR3 sodimm 2GB 666.7MHZ
Intel HD Graphics 2000
Monitor Lenovo LXM-WL20AH
HDD Seagate ST500DM002-1BD142

Have had 1 more BSOD, windows was installing updates when I Shut down the pc, this was early this morning, 7am. When I left at 11.30 it was still at it, when I came back had restarted with notice of bad shutdown, new minidump (attached) so I gues it BSODed again. The fact it was taking so long to install updates (in fairness they were like 250 updates, but some updates took for ever to process).

I have changed windows to create minidumps as per your request (was creating kernel dumps).
will run seatools for dos and diskcheck now and post back as soon as I have results.

Thank you very much for your help and time.
My System SpecsSystem Spec
26 Mar 2015   #5
Ivanissevich

Windows 7 Ultimate x64
 
 
SeaTools Tests PASSED

SeaTools for DOS would hang on the Lenovo with that drive, had to remove the drive and test in another PC. The drive passed the test. I also ran chkdsk without issues.

I installed another drive in the Lenovo, installed windows and have had it running with no issues for 2 days (installing programs, updating windows, etc). Interestingly, SeaTools for DOS worked on the Lenovo with this drive installed. The drive failed the short test, passed the long test.

The original Lenovo drive is installed in another PC and hasn't presented any issues so far, though its just a data drive with OS on another HDD.
My System SpecsSystem Spec
26 Mar 2015   #6
essenbe

Windows 7 Enterprise X64/Windows 10 Enterprise X64/Windows 10 Pro X64/Linux Mint
 
 

It looks like it was the Hard Drive.

Code:
KERNEL_DATA_INPAGE_ERROR (7a)
The requested page of kernel data could not be read in.  Typically caused by
a bad block in the paging file or disk controller error. Also see
KERNEL_STACK_INPAGE_ERROR.
If the error status is 0xC000000E, 0xC000009C, 0xC000009D or 0xC0000185,
it means the disk subsystem has experienced a failure.
If the error status is 0xC000009A, then it means the request failed because
a filesystem failed to make forward progress.
Arguments:
Arg1: 0000000000000020, lock type that was held (value 1,2,3, or PTE address)
Arg2: ffffffffc000009d, error status (normally i/o status code)
Arg3: fffffa8005d047c8, current process (virtual address for lock type 3, or PTE)
Arg4: 0000000000000000, virtual address that could not be in-paged (or PTE contents if arg1 is a PTE address)
Debugging Details:
------------------

ERROR_CODE: (NTSTATUS) 0xc000009d - STATUS_DEVICE_NOT_CONNECTED
DISK_HARDWARE_ERROR: There was error with disk hardware
BUGCHECK_STR:  0x7a_c000009d
My System SpecsSystem Spec
Reply

 BSOD CRITICAL_OBJECT_TERMINATION (f4)




Thread Tools Search this Thread
Search this Thread:

Advanced Search




Similar help and support threads
Thread Forum
CRITICAL_OBJECT_TERMINATION bsod
Hello, I have replaced memory sticks on my system and have been stable since December 2013. Came home to hook up a camera and ended up with this CRITICAL_OBJECT_TERMINATION blue screen. Please look at the 2/26/14 screen dump and advise me of what i should do.
BSOD Help and Support
BSOD Critical_Object_Termination 0x000000f4
Started getting BSOD a few months ago started out 1 or 2 every week or so but has gotten progressively worse. At the start it only happened while playing W.O.W or other MMOs, now it will happen at random on boot up. Before it happens there is always a chirp but I've not been able to pin point from...
BSOD Help and Support
Bsod critical_object_termination
First 2 BSOD I've had in a while and the error msg was CRITICAL_OBJECT_TERMINATION & PAGE_FAULT_IN_NONPAGED_AREA. Info: Windows 7 Ultimate x64 Full Retail Specs: - i7 core processor - 12 gb ram - 8 TB HDD System hardware is probably 6 months old & total uptime since reinstall is 29...
BSOD Help and Support
Newbie Needs Help; CRITICAL_OBJECT_TERMINATION BSOD
Thank you for taking time to read my post. I built my first computer (which should be associated with my profile) and am experiencing several BSOD's per day. I found a program called BlueScreenView but can't make out what specifically may be causing the crashes. I tried to attach the most recent...
BSOD Help and Support
(BSOD) critical_object_termination error
Hi everyone, My first post here as this is the first time I can't solve what's causing the BSOD on my own. I went through the sticky post and attached what was suggested in the zip file. Hardware: - Lenovo Thinkpad X200, Intel C2D 2.4 GHz, 3GB RAM OS - Windows 7: - Professional x64 -...
BSOD Help and Support


Our Sites

Site Links

About Us

Find Us

Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

Designer Media Ltd

All times are GMT -5. The time now is 15:26.

Twitter Facebook Google+



Windows 7 Forums

Seven Forums Android App Seven Forums IOS App