Windows 7 Forums

Welcome to Windows 7 Forums. Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks.


Windows 7: Frequent BSOD/PC freezing, error 4105, suspect ATI Radeon HD 5670

16 Apr 2015   #11
craftxx15

Windows 7 x64 Home Premium
 
 

Quote   Quote: Originally Posted by Arc View Post
Stress test the Graphics Card using Furmark.
Video Card - Stress Test with Furmark
Take a screenshot of the furmark window before closing it. Upload the screenshot for us. Also let us know if you have experienced any crash/BSOD and/or artifacts during the test.

Let us know the results.
Hi, here is my Stress Test screenshot with Furmark. My PC crashed/rebooted - with no dump file shortly after turning on today and visiting this website. But it didn't crash during the test which lasted about 11 mins.


My System SpecsSystem Spec
.
16 Apr 2015   #12
craftxx15

Windows 7 x64 Home Premium
 
 

Quote   Quote: Originally Posted by Arc View Post
Test your RAM modules for possible errors.
How to Test and Diagnose RAM Issues with Memtest86+
Run memtest86+ for at least 8 consecutive passes.

If it start showing errors/red lines, stop testing. A single error is enough to determine that something is going bad there.

Let us know the results.
I did run the Memtest86+ in Feb (I will include the screenshot), but I will run it again tonight because it lasts 16 hours.

Something I just noticed is that when I checked my Windows System config it was reporting that I only had 4 GB on board. When I rebooted and checked my CMOS, it read 8192 MB DDR3. I restarted Windows and checked the System again, it then reported 8 GB.
My System SpecsSystem Spec
16 Apr 2015   #13
Arc

Microsoft Community Contributor Award Recipient

Microsoft Windows 10 Pro Insider Preview 64-bit
 
 

OK, let us know the result of the Prime95 test too, when done.
My System SpecsSystem Spec
.

16 Apr 2015   #14
craftxx15

Windows 7 x64 Home Premium
 
 

Quote   Quote: Originally Posted by Arc View Post
OK, let us know the result of the Prime95 test too, when done.
Hi, I ran the Prime95 test for about 31 mins (with SpeedFan monitoring the temperatures).

My motherboard is Dell Inc 05DN3X i7 930 and the 4 x CPU cores soon hit temperatures of up to
98 deg C (Core 0) to 87 deg C (Core 3). I was afraid of burning them out at that temp - so I stopped
the test. They are now sitting at 44 Deg C to 39 Deg C.

I am attaching the results.txt file.

I will start the MemTest86+ shortly.

And, no BSOD or crashes during these tests - just had the one reboot hours ago.
My System SpecsSystem Spec
16 Apr 2015   #15
Arc

Microsoft Community Contributor Award Recipient

Microsoft Windows 10 Pro Insider Preview 64-bit
 
 

The test ran good upto that time. But it got too much high temp there.

Two information will be needed there. What is the wattage of your installed PSU? And which CPU cooler is applied there?

Let us know.

You may need to open the computer to know these things.
My System SpecsSystem Spec
17 Apr 2015   #16
craftxx15

Windows 7 x64 Home Premium
 
 

Quote   Quote: Originally Posted by Arc View Post
The test ran good upto that time. But it got too much high temp there.

Two information will be needed there. What is the wattage of your installed PSU? And which CPU cooler is applied there?

Let us know.

You may need to open the computer to know these things.
Hi,

I opened my PC to get the info you requested. I removed and air sprayed clean the CPU fan and heatsink which were dusty. In hindsight, now I need to get some thermal paste to properly seal the CPU and heat sink. I think that will cool down my system a lot. I also had to remove the PSU to read the manufacturer's label. Note: I am not a PC tech - I have 30+ years experience in the IT field - more in operations and security.

1. My PSU is a Dell D525AF-01 @ 525 W

2. The Dell Studio XPS 9100 has a heatsink/fan assembly - part no. P281K?


The good news is that my PC hasn't crashed all day! And it has been running pretty much 36 hrs.
My System SpecsSystem Spec
17 Apr 2015   #17
craftxx15

Windows 7 x64 Home Premium
 
 

Quote   Quote: Originally Posted by Arc View Post
Test your RAM modules for possible errors.
How to Test and Diagnose RAM Issues with Memtest86+
Run memtest86+ for at least 8 consecutive passes.

If it start showing errors/red lines, stop testing. A single error is enough to determine that something is going bad there.

Let us know the results.
I ran this test for 8 passes and almost 17 consecutive hours - with no errors (or crashes).
My System SpecsSystem Spec
17 Apr 2015   #18
Layback Bear

Windows 7 Pro. 64/SP-1
 
 

Couple of things.
Your temps in MemTest might be incorrect.

For a spot check of temps for a Intel CPU try using Real Temp.

Real Temp - CPU temperature monitoring


Let us know what the difference is in temp readings.

Are you over clocking in any fashion??
My System SpecsSystem Spec
17 Apr 2015   #19
craftxx15

Windows 7 x64 Home Premium
 
 

Quote   Quote: Originally Posted by Layback Bear View Post
Couple of things.
Your temps in MemTest might be incorrect.

For a spot check of temps for a Intel CPU try using Real Temp.

Real Temp - CPU temperature monitoring


Let us know what the difference is in temp readings.

Are you over clocking in any fashion??
I ran MemTest86+ from a bootable DVD and the pgm runs without Windows opening (like a DOS window). So I am not sure how I could compare the temps with Real Temp at the same time MemTest is running.

I did download Real Temp and had it running along side SpeedFan - both monitoring the CPU in Windows in a virtually idle state. Both reported almost identical temps - which were high in my opinion: Core 0:54C, 1:53C, 2:53C, 3:51C

When I turned off Real Temp, the temps went down to 48 to 44 deg C. Still too hot - I think I didn't get the Heatsink sealed properly earlier today - now I have to wait to get some thermal paste, which will take me a few days.

And, I am not over clocking. Thanks for your interest!
My System SpecsSystem Spec
17 Apr 2015   #20
Layback Bear

Windows 7 Pro. 64/SP-1
 
 

You are correct you won't be able to use a Temp program while you are using MemTest.
Once you are in Windows 7 you can use RealTemp to monitor your temps.
The 930 cpu like all 900 series Intel cpu do run a little hot normally. Your cpu has a on die memory controller so when testing the ram cpu temps will clime.

I have a i7-960 with a Corsair H80 push/pull and my temps are about 10C cooler than yours and I'm over clocked.
What I do is check the bios temps compared to RealTemp and see how close they are. That give some idea if RealTemp is reading your temps correctly.

Then I put RealTemp on the Taskbar and watch the temps while I do test or normal use.
With a stock cooler I personally don't recommend running things like Prime95 to load test your cpu. Temps will go sky high very fast.

Just monitor your temps while you are work your system hard. That will give you a real world temp readings.
My System SpecsSystem Spec
Reply

 Frequent BSOD/PC freezing, error 4105, suspect ATI Radeon HD 5670




Thread Tools Search this Thread
Search this Thread:

Advanced Search




Similar help and support threads
Thread Forum
ATI AMD Radeon HD 5670 - BSOD
I have a 1024MB ATI AMD Radeon HD 5670 (Dell) as my graphic card and when I play Counter Strike Global Offensive I get a Blue Screen of death with the error I opened up Speccy on my 2nd monitor while playing and I saw my graphic card temperature going from 61 Celcius to 75 as soon as I started...
Graphic Cards
BSOD crashes after updating/reinstalling Radeon HD 5670
Hi. I'm new to the forum and not quite sure how else to proceed with my BSOD issues. I play WoW, but only started playing again recently after a few years break. I updated my Radeon HD 5670 driver and started getting black screens, errors, driver non-responsive/restarting, BSOD's, etc. I made...
BSOD Help and Support
Frequent BSOD, suspect wdf01000.sys and ntoskrnl.exe
I'm running Windows 7 Pro (64-bit) and at various times throughout the day, no matter what I have open, I get the same BSOD error - DRIVER_IRQL_NOT_LESS_OR_EQUAL. DM Log Collector zip file is attached. Any assistance would be most appreciated.
BSOD Help and Support
Ati Radeon X1650 ---> upgrade to Radeon HD 5670
Hi all, (sorry for bad english): I bought a new graphics card (PCI-Express) to replace the old one that came with my computer: the old one is the ATI Radeon X1650, with 512 MB DDR2 memory; the new one is the ATI Radeon HD 5670, with 1 GB GDDR5 memory. I run Windows 7 Professional on an...
Graphic Cards
Overclocking Ati Radeon 5670
I have an ati radeon 1 gb graphic card, since my monitor only supports 1368 * 768 resolution it was enough to play most of the games in highest graphic settings. Crysis 2 in extreme settings gives me around 45-50 fps. Recently i updated the dx11 patch and only with the ultra settings it gives +-35...
Graphic Cards
ATI Radeon HD 5670 Problem
I recently downloaded Windows 7 Ultimate 64x, and I've been experiencing problems with either my Graphics card, or my Monitor. At first when I restarted my computer as soon as the computer was about to load in the login screen for Windows 7 it went black. You could see the mouse pointer, and...
Graphic Cards


Our Sites

Site Links

About Us

Find Us

Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

Designer Media Ltd

All times are GMT -5. The time now is 06:48.

Twitter Facebook Google+



Windows 7 Forums

Seven Forums Android App Seven Forums IOS App