Windows 7 Forums

Welcome to Windows 7 Forums. Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks.


Windows 7: BSODs persist after clean install

31 May 2015   #1
toranaboy

Windows 7 Home Premium 64 bit SP1
 
 
BSODs persist after clean install

I deleted all partitions on the HDD. I installed the latest drivers for the ASRock Mboard. I have installed little else. The info regarding crashes prior to new installation are uploaded herewith. And ditto with the latest crash. Also a speccy report. I would be grateful for some help.

I have been trying to migrate to linux on this box due to the grief of instability, but I couldn't make dual boot work at all and weird stuff affected startup. Even now, after refreshing the HD the machine stops on boot to display: 'remove disks or othe' (yes, really: 'othe') even though there is no DVD etc in the optical drive.

Help!


My System SpecsSystem Spec
.
31 May 2015   #2
Boozad

W7 Pro x64 SP1 | W10 Pro IP x64 | W8.1 Pro x64 VM | Linux Mint VM
 
 

The one single dump in your log is a 0xC5 which indicates a driver is corrupting the system pool, there's no driver listed in the dump at all however.
Code:
DRIVER_CORRUPTED_EXPOOL (c5)
An attempt was made to access a pageable (or completely invalid) address at an
interrupt request level (IRQL) that is too high.  This is
caused by drivers that have corrupted the system pool.  Run the driver
verifier against any new (or suspect) drivers, and if that doesn't turn up
the culprit, then use gflags to enable special pool.
Arguments:
Arg1: 0000000000000008, memory referenced
Arg2: 0000000000000002, IRQL
Arg3: 0000000000000000, value 0 = read operation, 1 = write operation
Arg4: fffff80002dc9b15, address which referenced memory



BSODs persist after clean install Diagnostic Test BSODs persist after clean install
 DRIVER VERIFIER

Driver Verifier will stress your drivers and cause BSODs if any fail. Follow this tutorial to enable/disable it. Driver Verifier - Enable and Disable

Enable Driver Verifier but only enable these options:
  • Standard settings and IRP logging step 3.
  • Don't enable Force Pending I/O Requests
warning   Warning
Make a System Restore point before enabling Driver Verifier.
Note   Note
Your system will act very sluggishly while DV is enabled, this is normal as your drivers will be being subjected to heavy testing in order to make them crash.


Post any resulting dump files.

You also need to run all rounds of Windows Updates, your missing a lot of Hotfixes.
My System SpecsSystem Spec
31 May 2015   #3
Barman58

Windows 10 Pro x64 x2 Windows 10 Enterprise x64, Ubuntu
 
 

Speccy text removed for your protection - as it contained your complete COA details
My System SpecsSystem Spec
.

01 Jun 2015   #4
toranaboy

Windows 7 Home Premium 64 bit SP1
 
 
Other dumps

The second Kautsky-PC2 zip archive contains dumps going back to around the Cambrian Era A good few of those will have been forced by verifier. I am happy to run it but maybe there's some info there which might help. Please let me know. And thanks. And thanks for the speccy thing, I had, of course, no idea
My System SpecsSystem Spec
05 Jun 2015   #5
toranaboy

Windows 7 Home Premium 64 bit SP1
 
 
Verifier on

Verifier on and the first crash dump is uploaded herewith.
My System SpecsSystem Spec
05 Jun 2015   #6
Boozad

W7 Pro x64 SP1 | W10 Pro IP x64 | W8.1 Pro x64 VM | Linux Mint VM
 
 

The DV dump has shown a driver, your Intel USB 3.0 eXtensible Host Controller driver. It's pretty old and needs updating, check here for an updated version. I did check the Gigabyte support page for your motherboard but it lists an Etron USB 3.0 driver and no Intel driver, could you post a screenshot of Device Manager with USB Controllers expanded please.
Code:
BugCheck E6, {f, 3, fffff88003d0e000, 0}

*** WARNING: Unable to verify timestamp for iusb3xhc.sys
*** ERROR: Module load completed but symbols could not be loaded for iusb3xhc.sys
Probably caused by : iusb3xhc.sys ( iusb3xhc+37c43 )

Followup: MachineOwner
---------

0: kd> lmvm iusb3xhc
start             end                 module name
fffff880`058a2000 fffff880`05967000   iusb3xhc T (no symbols)           
    Loaded symbol image file: iusb3xhc.sys
    Image path: \SystemRoot\system32\DRIVERS\iusb3xhc.sys
    Image name: iusb3xhc.sys
    Timestamp:        Mon May 21 08:21:40 2012 (4FB9ED04)
    CheckSum:         000CA061
    ImageSize:        000C5000
    Translations:     0000.04b0 0000.04e4 0409.04b0 0409.04e4
My System SpecsSystem Spec
05 Jun 2015   #7
toranaboy

Windows 7 Home Premium 64 bit SP1
 
 
Mainboard update

I regret my system info was wrong. I think it is correct now. As revealed in the speccy file, the mobo is an ASRock B75 Pro3-M.

I will attend to the driver update
My System SpecsSystem Spec
05 Jun 2015   #8
toranaboy

Windows 7 Home Premium 64 bit SP1
 
 
USB controllers screenshot

Uploaded.
My System SpecsSystem Spec
05 Jun 2015   #9
Boozad

W7 Pro x64 SP1 | W10 Pro IP x64 | W8.1 Pro x64 VM | Linux Mint VM
 
 

You've updated the driver?
My System SpecsSystem Spec
05 Jun 2015   #10
toranaboy

Windows 7 Home Premium 64 bit SP1
 
 
USB 3 Extensible Driver Update

Done
My System SpecsSystem Spec
Reply

 BSODs persist after clean install




Thread Tools Search this Thread
Search this Thread:

Advanced Search




Similar help and support threads
Thread Forum
random Kernel-Power errors persist on clean install/new hardware
I had a system that was blue screening and having sporadic critical Kernel-Power errors. I have since replaced the power supply, motherboard, CPU, graphics card and RAM. the only parts that remained were the ODD and HDD.. I am still getting Kernel-Power errors ("information" and "error" level only...
Hardware & Devices
BSODs on clean install, usually from WMC or other video
Hi, I am going slightly crazy with BSODs. I recently had an issue with my setup and did a clean windows install. Since then I've been getting lots and lots of BSODs. I have tried doing 2 more clean installs to no avail. I have also: - run memtest for 24hrs - no errors - done a low level...
BSOD Help and Support
BSODs after clean install
Hi all! First of all im David, im 28 years old and im from southern Portugal (Vila Nova de Milfontes) near the sea :D Im having some issues with my pc and hope i can get some help because its getting annoying the impossibility of not resolving my problem. Here´s the deal, i formatted my...
BSOD Help and Support
Clean install, still get BSODS
32 bit Windows 7 Ultimate Clean full retail install of W7 (1 day ago) Age of system: 4-5 years old Nvidia GeFroce 9600 gt 3gigs ram I bought the computer pre-built, and I don't know the brand of motherboard/ram or what kind of motherboard it is. The two BSODS i've gotten today (1 day after...
BSOD Help and Support
BSODs with clean install 32bit
I installed my new release copy of Win7 about 10 days ago and have had 4 BSODs in that time. The first checked online and said it was probably hardware related and couldn't be more specific. I have used Vista on this HTPC for about 18 months and had many BSODs but they always gave a file name of...
BSOD Help and Support
Random BSODs in clean install...
Hey all, I got Windows 7 x64 Pro last week, upgrading from XP Pro 32. I keep getting random BSOD crashes. I'm not overclocking, I've done thorough memory tests and came back fine, and the system ran stably without ever crashing in XP for a month before installing 7. I've included some of the...
BSOD Help and Support


Our Sites

Site Links

About Us

Find Us

Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

© Designer Media Ltd

All times are GMT -5. The time now is 07:47.

Twitter Facebook Google+



Windows 7 Forums

Seven Forums Android App Seven Forums IOS App