Windows 7 Forums

Welcome to Windows 7 Forums. Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks.


Windows 7: First Custom Build....BSOD errors and flickering screen

13 Nov 2015   #11
axe0

Windows 10 Pro
 
 

The 3 most recent are not loading properly for me, but 1 is a 0x119 which points to graphical issues.
The other 2 are pointing to a write error.
Code:
PAGE_FAULT_IN_NONPAGED_AREA (50)
Invalid system memory was referenced.  This cannot be protected by try-except,
it must be protected by a Probe.  Typically the address is just plain bad or it
is pointing at freed memory.
Arguments:
Arg1: fffff88006c9bc78, memory referenced.
Arg2: 0000000000000001, value 0 = read operation, 1 = write operation.
Arg3: fffff800030937bc, If non-zero, the instruction address which referenced the bad memory
	address.
Arg4: 0000000000000001, (reserved)
Please uninstall everything of AMD using Display Driver Uninstaller and install new drivers from AMD. Please ONLY install the drivers, using custom/advanced options.

Please test your memory, a write error could mean the memory address was corrupted, not likely but it could.



First Custom Build....BSOD errors and flickering screen Diagnostic Test First Custom Build....BSOD errors and flickering screen
 RAM TEST

Run MemTest86+ to analyse your RAM. MemTest86+ - Test RAM - Windows 7 Forums

Note   Note


MemTest86+ needs to be run for at least 8 passes for conclusive results. Set it running before you go to bed and leave it overnight. We're looking for zero errors here. Even a single error will indicate RAM failure.



My System SpecsSystem Spec
.
13 Nov 2015   #12
cannoncd

Windows 7 - x64
 
 

Ok, will do.

I have run memtest86 in the past (but not since the most recent BSOD's). Would you like me to still run it?
My System SpecsSystem Spec
13 Nov 2015   #13
axe0

Windows 10 Pro
 
 

Yes please, usually when one runs it it isn't according to the above instructions.
My System SpecsSystem Spec
.

13 Nov 2015   #14
cannoncd

Windows 7 - x64
 
 

Ok. I have re-installed the drivers per the instructions above (did so in safe mode, as the DDU recommended).

I am still experiencing the "flickering program windows" issue.

I will run memtest overnight tonight, unless you think it's prudent I should do so immediately.
My System SpecsSystem Spec
13 Nov 2015   #15
axe0

Windows 10 Pro
 
 

I would recommend to run it overnight, unless you don't have to use your pc.
My System SpecsSystem Spec
13 Nov 2015   #16
cannoncd

Windows 7 - x64
 
 

Will do.

Interesting that it just happened now, but as the screen flickering continued, my monitors (I'm running three) blacked out and I got a notification that my display driver crashed, but had recovered. I have seen this happen a handful of times in the past. Just another data point FYI.

The screen flickering has also stopped.
My System SpecsSystem Spec
13 Nov 2015   #17
axe0

Windows 10 Pro
 
 

Does the flickering also happen when just 1 monitor is connected?
My System SpecsSystem Spec
13 Nov 2015   #18
cannoncd

Windows 7 - x64
 
 

Since building the computer, it's always had 3 monitors connected (I play a MUD in which multiple screens are very handy).

I can certainly try with just one monitor connected, but the flickering doesn't always happen (I'd say about ~30% of the time).
My System SpecsSystem Spec
13 Nov 2015   #19
axe0

Windows 10 Pro
 
 

Try it with only 1 monitor and see what happens
My System SpecsSystem Spec
13 Nov 2015   #20
cannoncd

Windows 7 - x64
 
 

Alright, will do.

However, the reason I built the system myself was to ensure I had a graphics card that could support 3 monitors (I had fairly minimal requirements elsewhere, so I didn't need to go crazy buying a high end gaming computer).

If the fix ends up being "use only one monitor," what can I do to return to 3 monitors? I imagine the answer might be....buy a new graphics card? Heh.
My System SpecsSystem Spec
Reply

 First Custom Build....BSOD errors and flickering screen




Thread Tools Search this Thread
Search this Thread:

Advanced Search




Similar help and support threads
Thread Forum
Getting many different BSOD errors on new custom pc build
Hello folks, I am having issues with custom gaming rig I built not too long ago. It started basically after I finally got everything installed and happens randomly throughout gaming or even just my wife doing online school. Even the BSOD crash errors are random not showing any particular...
BSOD Help and Support
Random BSOD errors, new custom build system, tried reformat.
I recently built a new system with my father and he has been having random BSODs with always a different error from day one. Unfortunately he tried to re-install so all I have is one .dmp file since the re-install. 0x7E dxgmms1.sys was the last one he encountered, I have an email with the...
BSOD Help and Support
BSOD Issue Custom Build PC, Screen and Sound go Haywire
Hello I've been having a BSOD issue that started last month. It has happened 7 times and i've ran memtest and checked my hard drives and they appear to running smoothly. The issue occurs when my computer has been left on for a while and often begins with the screen blurring and sound going...
BSOD Help and Support
Custom APU build, but has several windows update errors after instal
Hello, I just built a low cost PC for my parents, but I'm having trouble with several updates after I installed windows 7 Pro x64. I've tried going through the "get help with this error" link, but with no luck/confusing instructions. Code 800B0100 Code 800F0902 Code 9C57
Windows Updates & Activation
Various BSOD errors occurring seemingly randomly. Custom build.
My OS is Windows 7 Professional x64 These seem to happen erratically, at apparently random times, regardless of how heavily my system resources are being used. I've gone weeks without any errors, and I've faced several errors on the same day, even under the same computer usage patterns. I...
BSOD Help and Support
Constant BSOD on new custom build - Various Minidump Errors 0x0000003b
Hi Guys, This is my first attempt at building my own computer so I am not a pro by any means. I've been having issues with blue screens ever since I put the thing together. All the parts are new out of the box. When I first put the machine together I did some troubleshooting on my own and...
BSOD Help and Support


Our Sites

Site Links

About Us

Find Us

Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

Designer Media Ltd

All times are GMT -5. The time now is 09:04.

Twitter Facebook Google+



Windows 7 Forums

Seven Forums Android App Seven Forums IOS App