Windows 7 Forums

Welcome to Windows 7 Forums. Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks.


Windows 7: BSOD on startup - page_fault_in_nonpaged_area - can't access safe mode

25 Jul 2016   #1
Jackwaller30

Windows 7 Premium 64bit
 
 
BSOD on startup - page_fault_in_nonpaged_area - can't access safe mode

I've had this problem for the past couple of days. Every time I turn on my laptop I get the blue screen and it restarts. I've used the repair tool and that's got me to the point of logging in. I get the welcome message but then it shuts down and restarts and I get the blue screen again. I've tried to use safe mode and it either shows me the blue screen or logs in for a second and then shuts down. I'm using Windows 7 on a hp elite book 8570w. I think the issue may have been caused by a new update being installed automatically when I didn't have my power cable plugged in and I ran out of battery.

this is what the blue screen says:

A problem has been detected and windows has been shut down to prevent further damage to your computer.

PAGE_FAULT_IN_NONPAGED_AREA

Technical information:

** STOP: 0x00000050 (0xFFFFFA8209F7883A, 0x0000000000000000, 0xFFFFF800049A8E30, 0x0000000000000005)

any advise would be great, thanks in advance.

Jack


My System SpecsSystem Spec
.
25 Jul 2016   #2
axe0

Windows 10 Pro
 
 

Lets see if we can identify the problem, 0x50 in safe mode usually relates to the memory or NTFS problems.
Please start with MemTest86+, for 8GB it could take 8-10h or more to reach at least 8 passes.
16GB takes normally 1 day but could take up to 2 days.



BSOD on startup - page_fault_in_nonpaged_area - can't access safe mode Diagnostic Test BSOD on startup - page_fault_in_nonpaged_area - can't access safe mode
 RAM TEST

Run MemTest86+ to analyse your RAM. MemTest86+ - Test RAM - Windows 7 Forums

Note   Note


MemTest86+ needs to be run for at least 8 complete passes for conclusive results. Set it running before you go to bed and leave it overnight. We're looking for zero errors here. Even a single error will indicate RAM failure.


Make a photo of the result and post it.

Addition:
If errors show up you can stop the test, remove all sticks but 1 and test this single stick in each slot for 8 passes or until errors show, switch sticks and repeat.
If errors show up and you see them a lot later, no problem, the errors don't affect the test.
My System SpecsSystem Spec
25 Jul 2016   #3
Jackwaller30

Windows 7 Premium 64bit
 
 

Hi Axe0,

Many thanks for your reply. I tried a few more memory tests from the boot menu and that seemed to do the job. I restarted it a couple more times and it finally worked. I'm currently backing up all my files. If I get the same issue. I'll download Memtest.

Thanks for your help.

Jack
My System SpecsSystem Spec
.

25 Jul 2016   #4
axe0

Windows 10 Pro
 
 

Sounds like you performed built-in memory tests, though they don't do anything regarding fixing memory problems, memory tests are only capable of diagnosing the memory to see if there is a failure somewhere but they cannot do anything more.
My System SpecsSystem Spec
Reply

 BSOD on startup - page_fault_in_nonpaged_area - can't access safe mode




Thread Tools Search this Thread
Search this Thread:

Advanced Search




Similar help and support threads
Thread Forum
BSOD during windows startup; can't safe mode; startup repair can't fix
Consistent BSOD during Windows startup for both normal mode and safe mode. BSOD problem started shortly after buggy installations of Microsoft Visual C++ 2005 x64, Microsoft .Net Framework 1.1, and AMD Catalyst Drivers 13.9; and turning off Microsoft .Net Framework 3.5.1. Startup Repair is...
BSOD Help and Support
BSOD on Startup, safe mode is OK. Urgent!
Hey guys! Long story short, went from 7850, to 7970, to gtx680 that is now RMA back to the old 7850, and getting a new 7970 on sunday. Now, I uninstalled everything I can find that has to do with either nVidia or AMD, and it still BSOD right on startup: ...
BSOD Help and Support
Cannot access Safe Mode but can boot in Safe Mode with Networking
After attempting to start my Laptop in Safe Mode, it loaded drivers normally only to crash a few seconds later. A prompt message appears but is impossible to read because Windows immediately reboots upon showing the prompt. Safe Mode with Networking loads normally. Any ideas or advice? The...
BSOD Help and Support
BSOD on startup, safe mode too
I have recently upgraded my pc and it was working fine, then this morning I turned it on, tried to log on and it crashed. When I tried to log on again the BSOD popped up. I tried to start it up in safe mode, it worked the first time then when I tried again it popped up with the BSOD. I can't get...
BSOD Help and Support
BSOD during startup for normal mode. Can only start in safe mode.
I had this machine built just over a year ago, and only had occasional crashes (no particular activities seemed to generate the issue). About 2 months ago the crashes became more persistent, and upon restarting the machine would have trouble loading normal mode. At the screen that reads "welcome"...
BSOD Help and Support
BSOD can't access safe mode
I was recently having problems with installing Microsoft Silverlight on my Windows 7 64bit laptop. I followed instructions on several forums which told me to remove the program using comand prompt. I tried doing this but it couldn't find the specific file so i uninstalled it using add remove...
BSOD Help and Support


Our Sites

Site Links

About Us

Find Us

Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

Designer Media Ltd

All times are GMT -5. The time now is 14:53.

Twitter Facebook Google+



Windows 7 Forums

Seven Forums Android App Seven Forums IOS App