Hello you 7 gurus. I'm back with some new minidump files. Any help you ppl can give me would be greatly appreciated. BTW, no commonality to give you on these other than the computer was at rest(not in use). It was not sleeping or in hibernation, just resting. Wish I could give you more help. I have run mem diag, everything there is fine. I have also ran startup repair because after the second(?) bsod she wouldnt come back up.
Wow, no help? Is it that bad? Oh yeah, and COD4 is apparently crashing all the time now.
your "SSPORT.sys fffff880`08b86000 fffff880`08b8e000 0x00008000 0x42fbda34 11/08/2005 23:07:32" driver needs updating , would it be a samsung printer ?
your problems all look like ram issues with stop error 0x0000001a pointing to MEMORY_MANAGEMENT,
I suggest you run memtest86 overnight for at least 3 passes and post back here if you get any errors,
what size and make of Power Supply do you have as these crashes can be caused by voltages dropping on the ram ?
or even bad contact in the ram slot ?
I have a corsair 550watt psu, i know, but heres the thing. Everything has been fine for months since I pulled one of my cards out(a bad ram card). Nothing has changed hardware wise. I have'nt even taken anything apart only a cleaning about two weeks ago. My pc runs 24/7 and it never has problems, maybe more bad ram? Or bad MoBo? I'll run memtest again and let you know.
What speed are your Dominators rated for
and what are they running at currently? Speed/Timing/Voltage
They are rated at 1333. mem freq @ 800(ddr2)mhz. mem ratio 2.0 x. fsb freq 200 mhz. cas latency 5. Does that help? I think the voltage is at 1.8
Last edited by James7679; 06 Jan 2010 at 19:52. Reason: added voltage
Was looking at your board. it looks as if it's rated at DDR2 800 for the MEM standard up to 8GB. Thing is, with all 4 slots full, using 8GB this may, or may not be a issue as 4 slots full does put a greater load on the NB.....
Was thinking it could be something along these lines.
But if your running at 800mhz 5-5-5-15(18), you should be OK. Thats fairly relaxed settings. :-/ And the fact you said there was no issues until recently.
I would however, Bump the VDIMM to 1.9 - 1.95V
Dominators are be perfectly fine all the way to 2.1 (1066 speed)
non-the-less
If you have run MEMTEST and passed i would suggest:
Running IBT (Intell Burn Test) for 5-10 passes , at a MAX stress level.
In order to find out if the NB itself is under too much stress with all 4 slots full.
I have a feeling its not the cause here, but it wouldnt hurt to test and see to be sure stability along the NB isnt causing the occasional MEMORY_MANAGEMENT error..
Ok, I got up this morning to check the forum, booted the computer and checked the thread. I went to get a cup of coffee and came back to a BSOD, the desc was something like "irq_notless_than_orequal_to" with a code something along the lines of "stop0000003.....". As I was about to load this info with an explanation and the minidump, it BSODd again, this time with a "memory_management" tag and another "stop0000003....". In my frustration and lateness to work I was not able to sit there and reload all of this info. When I get home I will attempt to run the "IBT" and let you know the results. I do have one question, could this be related to Airbots thread (first one in this forum) entitled "sticky..."? Only ask because I have a large hd and I keep getting stop codes. Thanks again for your help.
Here are the minidumps from today. I am going to get intell burn test and run it. I'll get you the results.
Wishmaster, my friend, after going to Guru3d's wesite to download "intell burn test" I was confronted with a pretty hefty warning about this program. They state that it has been know to fry cpus and/or mobos. Is that a bunch of horse squeeze? I know my processor sucks, but I don't want to replace it right now. What are your feelings on this?
Quote