Any Vapers?

That has the usual 510 threaded stem on the bottom half that you twist on just like a tank. Once on you use the small flat bracket looking tool like you would a phillips head screwdriver to tighten it down fully. That has two points to go into either pair of notches.

As soon as you get it tight you will notice the bracket lines right up correctly and not offset at any angle so the tank will flip over in a straight line with the battery. The problem is that most vendors are rushed to order the next newest and miss the small accessories until that something new has been out for a few months. At first no one had any coils for the Atlantis tank until I looked around early this morning and went to order the third tank with the 5 pack of those.

The bracket however with one look at the quick snapshot of the ruined battery I took is something you would want since you will want to put it in your pocket and snap goes something once you bend it! Due to it's small size you know you will end up with it in your pocket at some time even for a few minutes where the bending adapter could prevent a similar mishap!

None so far with the contact since that is spring loaded and sticks up enough to insure proper contact. The only stubborn part a few times already has been with the snap since that has a tab that acts like a button when the tank is secured upright and the locking tab portion missing the opening where I had a little fuss on one of the batteries but had to work it a bit. Over time from wear and tear that will eventually get a bit sloppy having more play then needed.

Other then that you can walk around with a tank attached and not end up seeing what happened to the eGo battery in the other snapshot I took a year ago! I kind of wish something like this was available for other mods while due to it's small size Eleaf knew what would happen once people started walking around with it in a pocket with a tank attached.

It seems to be solid with a chrome plating while the vendor doesn't specify the material at all. A closer look with the enlarged pictures can be seen at the manufacturer's product but still without any mention of the material these are made from. iStick bending adaptor

I can imagine stainless steel or an alloy since the threading on the iStick itself is likely aluminum like the mod itself. Here's a review that goes over it in detail you can watch at eLeaf iStick Bending Adapter A Vapor Trail Channel Pre-Release First Look!

Well it's good that you asked them since this will serve as a reference for others later! You have to think ahead a little.

The review there was good and was worth posting it since it covers all the bases as far as the bracket except no one specifies the material while I suspect chrome plated SS. It's not flimsy and feels more like a higher carbon steel like stainless or another tool steel in order to work out.

Meanwhile if you know anyone looking for the iStick or want a second one like I did to have a spare it can grabbed for $30.99 once in your shopping cart using the purchase at the Vaping Discounts site. $30.99 Your Choice of Eleaf iStick 20W E-cigarette Mod

You have to use their link there however since the vendor shows $33 and $36 until added to the shopping cart where the discount in then automatic since you went through VD. That's about the lowest since it came out and I was running into $33.99 or $34.99 with the rest going at $39.99 or more.

I went with the blue not the black or silver(Silver bullet for two eGo silver batteries!) having to many black or silver color batteries. Now the Vision Spinner 1300mah battery doesn't feel so lonely as the only blue VV or VV/VW battery around.

This year I wanted to do things a bit differently by grabbing the upgrades during the specials not spread out like last year first getting the MVP and new tanks in October followed by the iTaste v3.0s and pair of eGo-V V3 Mega batteries in December followed once more by two Smok ACE mod and the Smok Groove II in January. NADA! While grabbing the the pair of iSticks and pre-order on the Smok Guardian E-Pipe II mod still at the start of the month I waited until the pre-Black Friday, BF, and Cyber specials to come up to go for the shopping list adding as I went.

I'll end up spending more this year some of that being gift shopping but with a much more focused product list with some extra eGo batteries added in for spares until the others wear out. Here I often have two or three batteries/mods going always one for menthol while getting a break from the previous day's other two flavors! Kind of breaks things up when a vendor emails you about the nicotine level since some more samples(just what I didn't need!) would be tossed in with the tank and spare coils ordered. I won't be ordering anything but spare printer cartridges come January 2015!

I have been using this Atlantis tank for a couple of days now and I have to say it's just totally awesome. It gives you such a great hit. If I want a good hit on the nautilus I need to draw on it very heavy for quite a few seconds. You can get the same hit in a fraction of the time on the Atlantis and on the wide open hole there is no effort at all. I love it. I keep trying my nautilus but it's no good I am hooked on the Atlantis. It seems the sweet spot for me is around 27w on it.
It's literally a different world to the nautilus.

I can't fault the IPV V2 either. It's an excellent bit of kit and with the purple efest it's lasting the day.

I seem to be vaping a lot less now. The new stuff just gives such a hit I simply don't need to be chugging on it nonstop like before.

Overall very pleased with my recent purchases.