Windows 7 Forums

Welcome to Windows 7 Forums. Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks.


Windows 7: This device cannot start. (Code 10)

07 Jun 2015   #1
paulj1x

Win 7
 
 
This device cannot start. (Code 10)

Serious guru points if you can solve this one!
Windows 7, UFDs and iPod Nano were working fine. Then I cloned the Windows 7 C drive using the Samsung Data Migration tool from an 840 Pro Series 2.5-Inch 256 GB SATA 6GB/s Solid State Drive MZ-7PD256BW to an 850 EVO 500GB 2.5-Inch SATA III Internal SSD (MZ-75E500B/AM). Running Windows 7 on the new cloned 850 I can't use any type of USB storage, including different brands of UFDs, or my iPod Nano. Device status for each of these says: "This device cannot start. (Code 10)" Other USB devices such as mice, keyboards, and Bluetooth adapters work fine.
I've tried everything I can find on the Internet, including the following:
Restarted the computer, maybe 50 times.
Tried updating drivers: I get "Windows has determined the driver software for your device is up to date."
Ran Windows Update several times.
Uninstalled ALL devices under Universal Serial Bus controllers and rebooted.
Tried Microsoft Fixit troubleshooter.
Looked for but was not able to find USB lowerfilter or upperfilter entries in registry editor (HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Contro l\Class\), there are lowerfilter and upperfilter entries in other areas, including class diskdrives, the lowerfilter is SamsungRapidDiskFltr and upperfilter PartMgr, however I don't think that this is the problem since the Registry on the 840 system has the same entries. Interestingly, the registry export for the 840 Windows 7 is 607,727 KB and for the 850 (after clone) is 487,341 KB. Why such a huge difference? I'm tempted to input the 840 original Registry into the 850 new Registry, but concerned that there are such huge differences that it may cause serious problems.
I've tried these devices on other computers, they work fine. They also continue to work fine if I boot up when I go back to using the 840 system.
Uninstalled and reinstalled all Apple software.
I did find one other person who did a similar clone and ran into the same problem:
My PC can't install drivers for external USB drives | Page 3 - TechSpot Forums


My System SpecsSystem Spec
.
07 Jun 2015   #2
GokAy

Windows 7 Ultimate x64 SP1
 
 

Try cloning/imaging with Macrium instead?
My System SpecsSystem Spec
07 Jun 2015   #3
ComputerGeek

Desk 1: Win 7 Pro x32; Desk 2: Windows 10 x64
 
 

Let's double check and get more detail on those disk filters. Dowload/run FilterDriverLoadOrder Tool
> Select any UFD
> Click on the Clipboard button
> Paste the result into next post
My System SpecsSystem Spec
.

07 Jun 2015   #4
mvthakar

Microsoft® Windows® 7 Home Premium (x64)
 
 

I also once faced this problem in the past.
It turned out my Flash Drive was re-formatted to RAW.
I just had to format it from Disk Management.

But as you said that those devices of yours work fine in other computers.
It must be something else.

You could take a look at Disk Management though.
My System SpecsSystem Spec
07 Jun 2015   #5
paulj1x

Win 7
 
 

Quote   Quote: Originally Posted by ComputerGeek View Post
Let's double check and get more detail on those disk filters. Dowload/run FilterDriverLoadOrder Tool
> Select any UFD
> Click on the Clipboard button
> Paste the result into next post
Thanks ComputerGeek. I'm guessing that the drivers below are not the problem since they were the same on the original 840 system.
----------------------------------------------------
Filter Driver Load Order Professional software bus analyzers, USB, SCSI, iSCSI, SAS, ATA, ATAPI, Fibre Channel, and more!
----------------------------------------------------

Upper Class Filter: PartMgr
Device Object: Kingston DataTraveler 3.0 USB Device
Lower Class Filter: SamsungRapidDiskFltr

Driver Name: partmgr.sys
File Location: c:\windows\system32\drivers
File Description: Partition Management Driver
File Version: 6.1.7600.16385 (win7_rtm.090713-1255) [6.1.7601.17796]
Product Name: Microsoft® Windows® Operating System
Product Version: 6.1.7600.16385 [6.1.7601.17796]
Company Name: Microsoft Corporation

Driver Name: samsungrapiddiskfltr.sys
File Location: c:\windows\system32\drivers
File Description: Samsung RAPID Mode Disk Filter Driver
File Version: 1.0.1.81 built by: WinDDK [1.0.1.81]
Product Name: Samsung RAPID Mode
Product Version: Samsung RAPID Mode 1.0.1.81 [1.0.1.81]
Company Name: Samsung Electronics Co., Ltd.
My System SpecsSystem Spec
07 Jun 2015   #6
paulj1x

Win 7
 
 

Quote   Quote: Originally Posted by GokAy View Post
Try cloning/imaging with Macrium instead?
Unfortunately I thought that this would be a simple fix and I've done a lot with my 850 system, so recloning wouldn't be my first choice, but I might have to go that route.
My System SpecsSystem Spec
07 Jun 2015   #7
ComputerGeek

Desk 1: Win 7 Pro x32; Desk 2: Windows 10 x64
 
 

Do you need Samsung magician installed? Uninstall it. Check it removed the lower filter. Try it with the lower filter removed
My System SpecsSystem Spec
07 Jun 2015   #8
GokAy

Windows 7 Ultimate x64 SP1
 
 

Isn't your 840 still valid and working (original)? Clone 840 to 850 with Macrium, I meant. From your initial post I understand you performed the changes in 850. Only after you are done with other recommendations of course.
My System SpecsSystem Spec
07 Jun 2015   #9
paulj1x

Win 7
 
 

Quote   Quote: Originally Posted by ComputerGeek View Post
Do you need Samsung magician installed? Uninstall it. Check it removed the lower filter. Try it with the lower filter removed
Bing Bing Bing! I bow to Computer Geek!!! I uninstalled and reinstalled Magician and everything works perfectly now! Many many thanks!!!
My System SpecsSystem Spec
07 Jun 2015   #10
ComputerGeek

Desk 1: Win 7 Pro x32; Desk 2: Windows 10 x64
 
 

Quote   Quote: Originally Posted by paulj1x View Post
Quote   Quote: Originally Posted by ComputerGeek View Post
Do you need Samsung magician installed? Uninstall it. Check it removed the lower filter. Try it with the lower filter removed
Bing Bing Bing! I bow to Computer Geek!!! I uninstalled and reinstalled Magician and everything works perfectly now! Many many thanks!!!
You're most welcome. Glad I was able to help
My System SpecsSystem Spec
Reply

 This device cannot start. (Code 10)




Thread Tools Search this Thread
Search this Thread:

Advanced Search




Similar help and support threads
Thread Forum
This device cannot start. (Code 10)
I've got 2 Devices giving me the same problems. The only USB devices that do work are the mouse and keyboard. I do the same for both and get the same problems. A bit of background. Everythign was working perfectly, then I moved the computer downstairs, (in doing so unplugged all the usb devices),...
Hardware & Devices
Network Adapter - Device cannot start. (Code 10)
Hi, I cannot seem to get the etherent port to work on my new Asus P8Z77-V Motherboard, it will not connect with etherent cable at all altough there is a flashing orange light when i insert a cable. I have installed all the drivers from the disc, but on the driver propertise it says 'This device...
Network & Sharing
SD Memory Card - This device cannot start (Code 10)
I have an SD card that I use in my phone, and it's saying that it's corrupt. When I put it in the computer it doesn't appear in "My Computer", and in Device Manager I get "This device cannot start (Code 10). I have only found solutions for Windows XP computers, none for Windows 7. If anyone can...
Hardware & Devices
No sound - This device cannot start. (Code 10)
Hello! Since I got Win7 my sound isn't working anymore. When I go to sound it says "no audio devices are installed". And when I go to the device manager it says "this device cannot start (code 10)" It says that the drivers are up to date when I search for them, but I still tried to install...
Sound & Audio
USB device detected won't start (code 10)
I've done a fresh install of W7 yesterday on my desktop PC and I want to use the virtual PC for some USB hardware that doesn't have any x64 drivers. I can choose the USB devices fine in the virtual machine, they are detected and XP starts the usual hardware install wizard. However one of my...
Virtualization


Our Sites

Site Links

About Us

Find Us

Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

© Designer Media Ltd

All times are GMT -5. The time now is 17:33.

Twitter Facebook Google+



Windows 7 Forums

Seven Forums Android App Seven Forums IOS App