Install w7 64  


  1. Posts : 30
    W7 ULTIMATE
       #1

    Install w7 64


    Ok I have looked every where and can't find a driver for my sata drive. I only have and plan on using one sata3.0 drive. So I need windows installed on it. I followed the instruction for my mobo but every driver I try says it's not signed so can't use it. Went to gigabyte and tried th drivers no luck. Even true the vista drivers. No luck

    AMD Athlon II X2 240 Regor 2.8GHz Socket AM3 65W Dual-Core Processor
    Western Digital Caviar Blue WD6400AAKS 640GB 7200 RPM SATA 3.0Gb/
    GIGABYTE GA-MA785GM-US2H
    Antec Black M FusionRemote 350 Micro ATX Media Center / HTPC Case
    G.SKILL 2GB (2 x 1GB) 240-Pin DDR2 SDRAM DDR2 800 (PC2 6400) Dual Channel

    This is the first time I tried to install with a sata drive so I not sure if I'm doing it rite. Also first time win 7 also

    thanks
      My Computer


  2. Posts : 30
    W7 ULTIMATE
    Thread Starter
       #2

    43 views and not one idea. Man I'm
    stuck without this
      My Computer


  3. Posts : 1,705
    Windows 7 Ultimate x64 ®™
       #3

    Chvybeatsford said:
    43 views and not one idea.
    Tell us the steps you have taken already to try and install it?
      My Computer


  4. Posts : 28,845
    Win 8 Release candidate 8400
       #4

    Chvybeatsford said:
    43 views and not one idea. Man I'm
    stuck without this

    quick question

    Did you install the vista drivers in compatibility mode???

    As a work around if it is an external drive you could put it in an enclosure
      My Computer


  5. Posts : 30
    W7 ULTIMATE
    Thread Starter
       #5

    It's a internal drive. Clean install of w7. At least trying to install win 7. Jus my mono dosent show my drive. I changed the setting from IDE , raid ,and achi and still dosent see it. I am using the sata cable kit that plugs on the HD that has power and sata n one cable. Tried vista 64 drivers windows 7 64 drivers ,xp drivers the driver from gigabyte. Either way it jus says cannot use driver cause it's not signed.
      My Computer


  6. c59
    Posts : 28
    7rc
       #6

    When you say your motherboard does not show your drive do you mean that it is not listed in the bios setup? If it is not then windows will not find it.

    You say that you have one cable for both the sata and the power connection. at he drive end there should be 2 connectors as in the attached picture. The other end should have one connection going to the power supply and one going to a sata port on the mother board. Does that sound like the one cable you are using?
      My Computer


  7. c59
    Posts : 28
    7rc
       #7

    When you say your motherboard does not show your drive do you mean that it is not listed in the bios setup? If it is not then windows will not find it.

    You say that you have one cable for both the sata and the power connection. at he drive end there should be 2 connectors as in the attached picture. The other end should have one connection going to the power supply and one going to a sata port on the mother board. Does that sound like the one cable you are using?

      My Computer


  8. Posts : 30
    W7 ULTIMATE
    Thread Starter
       #8

    Srry i got it now seems the first sata cable i tried was bad. Got another and have windows installing At them moment.

    Thanks again.
      My Computer


 

  Related Discussions
Our Sites
Site Links
About Us
Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

© Designer Media Ltd
All times are GMT -5. The time now is 16:08.
Find Us