After clearing the bin the PC runs slow

Page 1 of 7 123 ... LastLast

  1. Posts : 32
    Windows 7 Ultimate 32bit
       #1

    After clearing the bin the PC runs slow


    Hi,
    I hope you can help me, after clearing the recycle bin the PC runs slow, and 5 minutes after the start a blackscreen apears that says: "boot0: error" how can i fix this?

    PS: sorry for the bad English
      My Computer


  2. whs
    Posts : 26,210
    Vista, Windows7, Mint Mate, Zorin, Windows 8
       #2

    Is this a Mac system ?
      My Computer


  3. Posts : 32
    Windows 7 Ultimate 32bit
    Thread Starter
       #3

    No itīs Windows 7 Ultimate 32 bit
      My Computer


  4. whs
    Posts : 26,210
    Vista, Windows7, Mint Mate, Zorin, Windows 8
       #4

    I would try a Startup Repair
      My Computer


  5. Posts : 32
    Windows 7 Ultimate 32bit
    Thread Starter
       #5

    sounds good, but this would presuppose that you have the Installation Disc, which I donīt have.
      My Computer


  6. whs
    Posts : 26,210
    Vista, Windows7, Mint Mate, Zorin, Windows 8
       #6

    No problem. Get one from Here. Make sure you get 7 Ultimate 32bit (x86).
      My Computer


  7. Posts : 32
    Windows 7 Ultimate 32bit
    Thread Starter
       #7

    ok, Iīll burn and run it tomorrow
      My Computer


  8. whs
    Posts : 26,210
    Vista, Windows7, Mint Mate, Zorin, Windows 8
       #8

    Where in Austria are you. We spent a lot of vacations in Velden.
      My Computer


  9. Posts : 32
    Windows 7 Ultimate 32bit
    Thread Starter
       #9

    In Upperaustria in Urfar-Umgebung,
    now back to topic: Iīve run the Startup repair 5 times by now, and it still doesnīt work
    the startup repair sais in the details:
    Session details:
    System Disc = \Device\Harddisk0
    Windows directory =
    AutoChk Run = 0
    Number of root causes = 1

    Test Performed:
    Name: Check for updates
    Result: Completed successfully. Error code = 0x0
    Time taken = 0 ms


    Test Performed:
    Name: System disk test
    Result: Completed successfully. Error code = 0x0
    Time taken = 0 ms


    Test Performed:
    Name: Disk failure diagnosis
    Result: Completed successfully. Error code = 0x0
    Time taken = 0 ms


    Test Performed:
    Name: Disk metadata test
    Result: Completed successfully. Error code = 0x0
    Time taken = 0 ms

    Root cause found:
    The partition table does not have a valid System Partition.

    Repair action: Partition table repair
    Result: Completed successfully. Error code = 0x0
    Time taken = 7347 ms


    so what should i do now? by the way the "C:" drive is located on a SSD and the "D:" drive is located on a HDD.
      My Computer


  10. Posts : 10,796
    Microsoft Windows 7 Home Premium 64-bits 7601 Multiprocessor Free Service Pack 1
       #10

    In recovery environment->command prompt:
    Code:
    diskpart
    list  volume
    What is the drive letter there of your win7 C drive? Assume it's called P there.
    Code:
    dir  P:\users
    you see the user accounts?

    Code:
    chkdsk/f  P:
    Replace P by real disk letter. What letter is it?

    Code:
    chkdsk/f  C:
    yes do C now.

    Errors found? Errors repaired? Try the commands again to prove it has corrected the disk errors.
      My Computer


 
Page 1 of 7 123 ... LastLast

  Related Discussions
Our Sites
Site Links
About Us
Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

Đ Designer Media Ltd
All times are GMT -5. The time now is 12:24.
Find Us