How to try out an older monitor with my desktop


  1. Posts : 5
    Windows 7 Professional 64 bit
       #1

    How to try out an older monitor with my desktop


    Do I need to tell my Windows 7 desktop (do an uninstall or similar action) before disconnecting current Dell wide screen monitor to try out an older Acer monitor from an XP OS ? Both are flat panel LCDs. Does it matter whether I disconnect the power cable first or the other cable ?
      My Computer


  2. Posts : 9,606
    Win7 Enterprise, Win7 x86 (Ult 7600), Win7 x64 Ult 7600, TechNet RTM on AMD x64 (2.8Ghz)
       #2

    Welcome Oteyallergy1 :)

    It would be the safest way to have computer & monitors powered OFF when switching the cables. But I have done it many times when powered on if very very careful .


    Is Otey a family surname from Virginia ?
      My Computer


  3. Posts : 3,487
    Win 7 Pro x64/Win 10 Pro x64 dual boot
       #3

    Windows will autodetect the different monitor. No need to do anything special, but change the monitor with the monitor and the computer powered off.
      My Computer


  4. Posts : 92
    Windows 7 Home Premium 64bit
       #4

    I don't see the need to change monitors while the computer is off. If you're afraid something could happen, set the resolution to 800x600 before changing the monitors. Also, if you can connect both at once that would be the best way.
      My Computer


  5. Posts : 3,487
    Win 7 Pro x64/Win 10 Pro x64 dual boot
       #5

    You don't plug monitors in with the power on for the same reason that you don't plug cards into the motherboard when the power is on. Transients and voltage spikes can cause damage to the equipment. Especially if pins with voltages on them get connected before the ground does.
      My Computer


  6. Posts : 92
    Windows 7 Home Premium 64bit
       #6

    Interesting, I've always hot-swapped monitors without any issue. If the power is connected before the ground, then it wouldn't complete the circuit and nothing would happen, right?
      My Computer


  7. Posts : 3,487
    Win 7 Pro x64/Win 10 Pro x64 dual boot
       #7

    The individual pins can be at different potentials (voltages). If power and another pin get connected before ground, you run the risk of doing damage. It might partially complete the circuit, treating the other pin as a ground, potentially placing more voltage on a pin than it can stand or is rated for. The actual circuit analysis is a little too complicated to get into here, but if you have the option, plugging in a multi pinned connector to anything should be done with the power off.
      My Computer


  8. Posts : 92
    Windows 7 Home Premium 64bit
       #8

    Doesn't every single connector in existence have at least 2 pins?
      My Computer


  9. Posts : 2,292
    Windows 7 Home Premium x64
       #9

    I can say from personal experience that hot-swapping monitors is a bad idea. It doesn't matter if it's worked for you before, it did the same for me until one time the monitor literally caught on fire. Besides, computers start up pretty quickly these days, especially with Windows 8 on them, so powering down your PC to change the monitors is really not such an annoyance.
      My Computer


  10. Posts : 3,487
    Win 7 Pro x64/Win 10 Pro x64 dual boot
       #10

    quadrplax said:
    Doesn't every single connector in existence have at least 2 pins?
    No. Some have one.
      My Computer


 

  Related Discussions
Our Sites
Site Links
About Us
Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

© Designer Media Ltd
All times are GMT -5. The time now is 09:41.
Find Us