Windows 7 Forums
Welcome to Windows 7 Forums. Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks.


Windows 7: Windows doesn't recognize all my hdd capacity.


23 Aug 2011   #1

Windows 7 Ultimate x64
 
 
Windows doesn't recognize all my hdd capacity.

Hello!
I've just bought a new laptop. It was with Linux Boot-Up system. I installed Windows 7 Ultimate x64. Installed all drivers that were on official Acer homepage. Then I saw that the Windows doesn't show all my HDD capacity. It should show 500gb, but it shows only 232GB.
What should I do?
my comp. -
Acer Aspire 5742G
HDD
WDC WD5000BEVT-22A0RT0
picture of my HDD
In attachment is screenshot from my PC.
waiting for replies,
best regards,
Hemis




Attached Thumbnails
Windows doesn't recognize all my hdd capacity.-untitled.png  
My System SpecsSystem Spec
.

23 Aug 2011   #2

windows 7 ultimate 32 bit
 
 

Hello hemis, you said when you bought your laptop, than there operating system was "Linux". Therefore, I think, your hardisk formatted as linux file system base. Windows file system and linux file system is totally different. So when you installed windows 7, at that time you format your c: drive. So widows seven only recognize your c: drive. Because window's seven recognize that file system. Please you format all of other partition on your hardisk by "NTFS" file system. To see your all of other partition go to "run" option and write "diskmgmt.msc" and then press enter. Here you see all of your hardisk partition. Now select drive and right click and then chose "format".

All the best.
My System SpecsSystem Spec
23 Aug 2011   #3

Windows 7 Ultimate x64
 
 

Thanks, finally I found the other partition of my HDD, but now there's a new problem. I can't press 'Format'.
what should I do?

edit - and what will happen if I'll press 'delete Volume'?


Attached Images
 
My System SpecsSystem Spec
.


23 Aug 2011   #4

Microsoft Windows 7 Home Premium 64-bit 7600
 
 

just a guess ,but have you clicked the partition you wish to format fist ,try selecting it and the see if format is still greyed out.
click where arrow points
Windows doesn't recognize all my hdd capacity.-2011-08-23_1038.png


My System SpecsSystem Spec
23 Aug 2011   #5

Windows 7 Ultimate x64
 
 

nop, there the menu even doesn't pop up...
My System SpecsSystem Spec
23 Aug 2011   #6
whs
Microsoft MVP

Vista, Windows7, Mint Mate, Zorin, Windows 8
 
 

Use the bootable CD of Partition Wizard (last entry on the webpage): Free Download Magic Partition Manager Software - Partition Wizard Online
My System SpecsSystem Spec
23 Aug 2011   #7

MS Windows 7 Ultimate 64-bit SP1
 
 

Hello Hemis,

Open Disk Management by going to Run and typing "diskmgmt.msc". Select the non C: partition (most probably a linux partition), right click with mouse and select "Delete Volume" and in next dialog box click on "Yes". This will remove the partition and make the space Unallocated. In this space you can create either single or multiple partitions.

To create a partition, right click on the unallocated space and select "New Simple Volume". This will open "New Simple Volume Wizard". Click Next. In this box to create a single partition filling complete unallocated space just click Next. Otherwise reduce the Size in Simple volume size in MB (up-down arrow buttons) or directly entering a value of your choice. Click Next and again Next.

Now select file system as NTFS (preferably for Win 7) or exFAT for a extended FAT partition. Keep default allocation unit size. At Volume Label you may give a name or do nothing. Put a check mark on "Perform a Quick Format" and no check mark on "Enable File and Folder Compression". Click Next and review the settings you have made so far and Click Finish to exit the wizard. Now in the Unallocated space a partition will be created and formatted with a drive letter which appeared and selected in the wizard.

You may always go back in the wizard before pressing Finish to change any values you have accepted before.
My System SpecsSystem Spec
23 Aug 2011   #8

Windows 7 Ultimate x64
 
 

thanks to all of you! problem solved with minitool partition wizard.
My System SpecsSystem Spec
Reply

 Windows doesn't recognize all my hdd capacity.




Thread Tools



Similar help and support threads for2: Windows doesn't recognize all my hdd capacity.
Thread Forum
Windows 7 doesn't recognize second monitor. Graphic Cards
Solved Windows 7 doesn't recognize my external HDD Hardware & Devices
Windows doesn't recognize DVD eject Drivers
Solved Windows doesn't recognize full capacity of hard drive Hardware & Devices
Windows doesn't recognize my printer Hardware & Devices
xp 32-bit to recognize full capacity of RAM General Discussion
Windows 7 Doesn't recognize USB HD Hardware & Devices

Our Sites

Site Links

About Us

Find Us

Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

© Designer Media Ltd

All times are GMT -5. The time now is 07:05 PM.
Twitter Facebook Google+



Windows 7 Forums

Seven Forums Android App Seven Forums IOS App
  

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33