Windows 7 Forums

Welcome to Windows 7 Forums. Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks.


Windows 7: BSOD after Windows Logo

23 Jul 2014   #1
jkility

windows 7 ultimate x64
 
 
BSOD after Windows Logo

Hi

I bought a new PC case and have fitted everything from the old case to the new case (No new hardware, just a straight swap). All plugged in and wired up etc but seem to be having a problem booting to my SSD.

Boot up PC and BIOS recognizes the SSD. Then it tries to boot into Windows and comes up with an error screen saying Windows Failed to Boot, would you like to do a startup repair, I say yes and let it do its thing, it restarts and tries to boot into Windows, gets as far as the logo screen and then BSOD with the following error:

"A problem has been detected and windows has been shut down to prevent damage to your computer.
If this is the first time you've seen this stop error screen, restart your computer. if this screen appears again follow these steps:

Check for viruses on your computer. Remove any newly installed hard drives or hard drive controllers. Check your had drive to make sure it is properly configured and terminated. Run CHKDSK /F to check for hard drive corruption, and then restart your computer

*** STOP: 0X0000007B (0XFFFFF880009A9928, 0XFFFFFFFFC0000034, 0X0000000000000000, 0X0000000000000000)"

Ran Seatools long and short tests and they both passed.
Booted into windows on another harddrive and ran Error Checking Check Disk and select both "Automatically fix file system errors and Scan for and attempt recovery of bad sectors, came up with errors and fixed them and still coming up with BSOD

I've got 2 other hard dries (1 bootable) and have managed to boot into windows with it and it works perfectly. I've got Hirens Boot CD and have attempted at running Check Disk but the F drive (SSD) is read protected and so is unable to. Not really sure where to go from here really.

Got a ASUS M5A99X EVO Motherboard if that makes a difference?


My System SpecsSystem Spec
.
25 Jul 2014   #2
ICIT2LOL

Desk1 7 Home Prem / Desk2 10 Pro / Main lap Asus ROG 10 Pro 2 laptop Toshiba 7 Pro Asus P2520 7 & 10
 
 

Hello and welcome jkility have you tried chkdsk in safe mode?
I f not try this and use the net access to run some scans for malware and look at what is in that drive.

BOOTABLEUBUNTU

Makea bootable Ubuntu disk http://www.ubuntu.com/download

Setthe BIOS to boot from the optical when the machine boots it will show you ascreen with TRY or INSTALL > select TRY. You can of course remove the hard drive and any otherdrives when doing this as if the optical alone is the only drive left in themachine then the BIOS will only find it to boot from.

Whenit is finished - it takes very little time you will get a screen like in thepic .

Openthe drive you want > User and dig down until you get to the data / settingsyou may be able to copy / paste the material you want to an external source orother installed drive doing this.

Iam not sure if it will but I have recovered tons of data etc using this methodboth on "dead" or just plain drives that you cannot get data fromusing Windows.


Attached Thumbnails
BSOD after Windows Logo-ubutux.png  
My System SpecsSystem Spec
25 Jul 2014   #3
Trini

Windows 7 Home Premium 32 Bit
 
 

I'm not familiar with Ubuntu so see if ICit2lol's method works. Putting in my 2 cents below.


Quote   Quote: Originally Posted by jkility View Post

Booted into windows on another harddrive and ran Error Checking Check Disk and select both "Automatically fix file system errors and Scan for and attempt recovery of bad sectors, came up with errors and fixed them and still coming up with BSOD
That particular hard drive, back up your info and throw it away. Once errors comes up, more will come in the future. No sense keeping it.

About the SSD, if you have a SATA-USB adapter, plug it in another computer and then run Windows Checkdisk choosing the option "scan for attempted recovery of bad sectors". If you come up with errors, do as what i stated above. If no errors, run Seatools on the SSD again doing long and short generic.

If no problems, then nothing is wrong with the SSD itself. You said you used another hard drive and you booted just fine which means nothing else is wrong hardware-wise. More than likely, your boot records got corrupted or an updated driver is causing the problem and you have to rollback the driver.

I would backup that SSD, format the drive and do a clean install of windows and see what happens.

Have you tried booting the SSD on safe mode?

About the motherboard, check this microsoft support link. It may help since it deals with your stop error code: Advanced troubleshooting for "Stop error code 0x0000007B (INACCESSIBLE_BOOT_DEVICE)" errors in Windows XP
My System SpecsSystem Spec
.

25 Jul 2014   #4
essenbe

Windows 7 Enterprise X64/Windows 10 Enterprise X64/Windows 10 Pro X64/Linux Mint
 
 

Try going into bios and check your sata controller and make sure it is set to what it was before the swap. It should be in AHCI with an SSD, but if you didn't set it that way, try IDE. If that doesn't work, set bios to optimized defaults.
My System SpecsSystem Spec
Reply

 BSOD after Windows Logo




Thread Tools Search this Thread
Search this Thread:

Advanced Search




Similar help and support threads
Thread Forum
a permanent bsod after windows 7 logo
Hello I am using windows 7 SP1 ,I am using this version for over than 2 years now and never faced this problem,now I am getting a permanent Bsod 0x0000006B after windows logo. I made some investigations and read a lot about the problem all over the internet and still can't figure out how to...
BSOD Help and Support
BSOD after Windows 7 logo
I just installed windows 7 on a fresh Hard disk on one computer. I put the hard drive into my other computer and after the windows logo it shows a BSOD (even in safe mode). The error code is "STOP: 0x0000007B (0xFFFFF880009A9928, 0xFFFFF880009A9928, 0x000000000... etc)" What do I do; as I...
Installation & Setup
BSOD On Windows Logo
My system first started to do some weird glitches like holds up for a few moments, than my mouse icon get weird graphics. So upon seeing some things I did Verifier and bam BSOD on the windows logo screen right away and a few times after so I know it a driver. I turn off Verifier and here is my Dump...
BSOD Help and Support
BSOD after Windows Logo
Hey guys... So my sister's laptop crashed after she started some game she didn't play in ages (Sims). It won't load the windows after the Windows logo. Only a BSOD. I can't go into safe mode, also I tried to restore to some restore point via the Windows Recovery which I can access. Any ideas? I...
BSOD Help and Support
BSOD/Restart after Windows Logo
Hi all! I really need help, everytime I try to install a Windows 7, it restarts or BSOD after the Windows 7 logo. Here's what happened. I'm gonna tell you how it started. I was just watching a video and suddenly my speaker started a crashing noises, so I removed the cable and tried...
BSOD Help and Support
BSOD After windows 7 logo
i had recently reformatted my friends computer and installed w7 ulti x86, and it had been workig fine for a while but now its constantly BSOD right after the w7 loading bar so i dont know how i can get minidumps it also does it if i boot in safe mode. im stumped and dont know wat else i can do i...
BSOD Help and Support


Our Sites

Site Links

About Us

Find Us

Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

Designer Media Ltd

All times are GMT -5. The time now is 16:12.

Twitter Facebook Google+



Windows 7 Forums

Seven Forums Android App Seven Forums IOS App