Windows 7 Forums
Welcome to Windows 7 Forums. Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks.


Windows 7: Can't connect IDE hard drive to SATA motherboard


23 Dec 2009   #11

Windows 7 64-bit
 
 

Try the jumper as slave.

My System SpecsSystem Spec
.

24 Dec 2009   #12

Windows 7 Home Premium
 
 

Doc,

Yes, it is recognized in BIOS. That is, when I can get into BIOS. Recently, I can't even do that with the drive connected.

raf051888,

I have tried the setting on Slave, Master, and Cable Select. Nothing changed the outcome.

Mike
My System SpecsSystem Spec
24 Dec 2009   #13

Win7 Enterprise, Win7 x86 (Ult 7600), Win7 x64 Ult 7600, TechNet RTM on AMD x64 (2.8Ghz)
 
 

Sometimes when I have connected an IDE HD via the USB adapter. I have to go to Computer Management >> Disk Management & then initalize the HD first, then I can format from within Disk Management. Then it seems to work ok !

Jump on board the Trial & Error Testing Train, we don't give up easily


" Doc "
My System SpecsSystem Spec
.


24 Dec 2009   #14

Windows 7 Home Premium
 
 

Hi Doc,

At this point, I'm riding first class on the train! As I mentioned previously, I can't even get into Windows with the drive connected. The few times I did make it that far, it kept telling me the "Device was not ready". I haven't been able to get into Windows for awhile now. Thanks for not giving up.

Mike
My System SpecsSystem Spec
24 Dec 2009   #15

Win7 Enterprise, Win7 x86 (Ult 7600), Win7 x64 Ult 7600, TechNet RTM on AMD x64 (2.8Ghz)
 
 

Mike,

I have to work a half day today, but I put on my Thinking Cap & check in later on this

Doc's train looking into the Future ?

" Doc "


Attached Thumbnails
Can't connect IDE hard drive to SATA motherboard-ready_to_roll.jpg  
My System SpecsSystem Spec
24 Dec 2009   #16

Windows 7 Home Premium
 
 

Doc,

Thanks. I'll send you some snow as payment! If you don't get back to this today, have a great Christmas.

Mike
My System SpecsSystem Spec
24 Dec 2009   #17

 
MOBO Specs

Attached are MOBO specs for support look to this link.
Motherboard Specifications, IPIBL-LB (Benicia) - HP Customer Care (United States - English)

Hope this helps.


Attached Images
  
My System SpecsSystem Spec
24 Dec 2009   #18

 

Quote   Quote: Originally Posted by Minnesotamike View Post
I have a problem and it's driving me nuts. I am new to Windows 7 and I'm not sure if I am missing a setting, in 7, to get this to work. Here's the problem.

I just bought an HP system (see specs) with SATA connections only. I have an IDE drive from my Windows XP system that I would like to install in my new system. I have tried a controller card and an adapter. Neither have worked. When I start the system, I get to the start up screen that gives me the option of entering BIOS, Boot Menu, and a couple others. Lately, it just stays there. If I leave it alone, it will go no farther. If I select either of the options, it says, "enter xxxx....", but it goes no where. If I disconnect the drive, it starts up normally. When I can get into BIOS, the drive is recognized and the original drive is set as the first to boot. I have even tried all the SATA Controller settings (IDE, RAID, AHCI) and nothing.

There had been a few times that I actually reached Windows, but the drive was listed as unallocated and I could do nothing with it. If I tried, I got the error message "Device not ready". Unfortunately, I can't even get that far anymore.

A format was suggested, so I copied all my data to my external drive and formatted in XP. No luck. I keep hearing that either setup should work, but it doesn't. The system is completely updated and the drivers for the controller card are the Windows 7 drivers from the manufacturer. Any thoughts on what to try? I do want this installed internally, not by USB. Thanks!

Mike
Welcome to WIndows 7 support.
Mike, lets try the obvious, if you are able to access your bios using F-10 at boot, select your boot priority to your SATA Drive as first boot.
Regards,
Adrian
My System SpecsSystem Spec
24 Dec 2009   #19

 
RAID

Are you set in BIOS to AHCI, or SATA for storage devices?
My System SpecsSystem Spec
24 Dec 2009   #20

 
Disk management

Mike I re-read your post, it seems that Windows 7 does post and boot but the IDE drive is showing as Un-Allocated. Doc has suggested that you use the following:
My Computer\Management\Disk Management\

Are you familiar with this procedure?
If not I can walk you through it.

Adrian
My System SpecsSystem Spec
Reply

 Can't connect IDE hard drive to SATA motherboard




Thread Tools



Similar help and support threads for2: Can't connect IDE hard drive to SATA motherboard
Thread Forum
Motherboard detects Sata SSD drive but not normal sata drives. Hardware & Devices
C Drive Connected to Motherboard SATA Connector 3 Instead of 0. Installation & Setup
Can I connect a SATA drive to an ESATA port? Hardware & Devices
How do I transfer files from bad sata hard drive to new hard drive Installation & Setup
Install Windows 7 with Sata Hard Drive and IDE DVD ROM Drive Installation & Setup
Sata Hard drive Hardware & Devices
Hard Drive Dissapears after installing 2nd SATA Drive Hardware & Devices

Our Sites

Site Links

About Us

Find Us

Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

Designer Media Ltd

All times are GMT -5. The time now is 08:24 AM.
Twitter Facebook Google+



Windows 7 Forums

Seven Forums Android App Seven Forums IOS App
  

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33