System won't boot after removing second hard drive, EFI?

Page 1 of 3 123 LastLast

  1. Posts : 3
    Windows 7 Pro x64
       #1

    System won't boot after removing second hard drive, EFI?


    So this I've never encountered, not sure what to think about it. Hopefully someone can give me a hand.

    I re-installed windows 7 to a fresh hard drive, while keeping my old hard drive with old install of windows still in my computer so I could transfer any personal files over later.
    Upon startup, Windows boot manager lets me choose the new windows installation (default) or the previous one. Both boot properly.

    However, if I try and remove the old hard drive from the system, it just give me a black screen when I boot.

    I've tried changing the boot order of the drives in bios; it's giving me 'windows boot manager' as default, which I assume is giving me the menu to choose OS. If I change it to boot the main hard drive first, and ignore the second hard drive, it does the same thing (not booting).

    Did I screw something up ? Did installing windows with the second drive attatched write some part of the boot partition on the second HD (disclaimer: I know little about what windows uses to boot).

    In disk management, what should I be expecting to see ? Currently I have disk 0 (C: one large NTFS partition with boot, page file, crash dump, and primary) and disk 1 (includes one 100MB partition for EFI System Partition, and one large NTFS partition for D: as a primary partition).

    Am I correct in thinking that the EFI System Partition needs to be on the main drive ? I've since learned that's what Win 7 does apparently, if there's already an EFI System Partition anywhere on drives, it adds the new OS info to that.

    So, short of reinstalling windows with only the main drive in, is there anything I can do to move it, or delete and restore it on the main drive ? I don't care about the second hard drive being bootable, but I'm not quite ready to format it (and am unsure what would even happen at this point if I did).

    If anyone can guide me in what to do. If reinstalling windows is the only option, I'd rather just leave the ******* second drive in there and forget about it. Otherwise, since I've already set up this fresh install of windows exactly as I like it (I'm picky), and didn't really have the time to reinstall it and start again from scratch, is there a way to perfectly and reasonably easily back this up then restore it if I were to reinstall windows?

    Any help would be appreciated. This is really doing my head in.

    Thanks.
      My Computer


  2. Posts : 10,796
    Microsoft Windows 7 Home Premium 64-bits 7601 Multiprocessor Free Service Pack 1
       #2

    Your boot files are in the 100MB partition! Post screenshot of disk management
      My Computer


  3. Posts : 10,796
    Microsoft Windows 7 Home Premium 64-bits 7601 Multiprocessor Free Service Pack 1
       #3

    With both disks attached Do this:

    Bootmgr - Move to C:\ with EasyBCD

    Then mark 100MB partition on old drive inactive to prevent to use it as BOOT partition
    Partition - Mark as Inactive

    Now it works
      My Computer


  4. Posts : 240
    Win 8 RP, Win 7, XP
       #4

    Does EasyBcd support EFI/UEFI ?
    Which version ?
      My Computer


  5. Posts : 3
    Windows 7 Pro x64
    Thread Starter
       #5

    This is what I'm looking at in disk management. The EFI partition isn't touchable at all in this (context menu is completely greyed)

    Also, EasyBCD has zero EFI and GPT support from what I can tell.

    So unfortunately this isn't going to help me.

    It appears there aren't any tools that will solve this yet. This EFI thing is pretty intent on staying where it is, without a full re-install.

    So, either I leave everything as it is (because like I said, I'm not even sure what happens if I format the second drive...

    So, my second question then. If I were to do a full back up of the new install, reinstall windows with only the one disk plugged in, then restore the back up, will everything be restored as it is now?
    I've actually never made backups of windows, ever. So I'm not sure what to expect.

    Is it possible to make a perfect back up of this and restore ? Does it include everything such as drivers, installed programs, and various settings ? (ie, would I notice a difference from it's current state now?)

    The reason I'm trying to avoid reinstalling is that I actually don't really have the time to do it again (I'm finicky about how it's set up, and I have to be working tomorrow, not downloading drivers, software, and setting up again.)

    Again, any advice is appreciated.
      My Computer

  6.    #6

    I would redo the Clean Reinstall correctly with the other HD unplugged.

    EFI installs provide many complications including with repairs which is why we cannot use normal methods to repair your new install so it boots on its own, which are to unplug the other HD, mark Win7 Active then run Startup Repair - Run 3 Separate Times

    What I would suggest you do is remove EFI boot disk from the BIOS setup Boot Order, then clean and format the target HD (by itself) using Diskpart Clean Command followed by the command Convert MBR. Access DISKPART At PC Startup .
    You can then install normally. After install plug in the other HD to access it's data.

    If you want to install using EFI, follow these instructions: UEFI (Unified Extensible Firmware Interface) - Install Windows 7 with - Windows 7 Forums which are more trouble than their worth, and require difficult steps to repair Win7.
      My Computer


  7. Posts : 1,031
    Windows 7 x64
       #7

    It seems you second install is also a EFI install. If you had installed them without the other drive installed, you would have gotten two Windows Boot Mangers, each with the drive ident attached - hopefully.

    I think your problem now, is that there is no room on the new drive for the EFI partition. If you were to shrink the partition so you had some unallocated space, a startup repair would probalby add the partition behind the first one.

    The second drive is probably configured as a GPT drive, so you can't use an active partition and boot directly to it. If it is not a GPT drive, you could. To check if it is configured as GPT, right click the info box on the left end of Disk Management and see if it says "Convert to GPT" or "Convert to MBR". It will, of course, be the one not listed as convert.
      My Computer


  8. Posts : 1,031
    Windows 7 x64
       #8

    This post concerns restoring boot capability to a UEFI install when the install drive being used does not have a EFI partition, such as the situation in this thread.

    The overall process is much like a Legacy (MBR) install where you do not have an active partition with the boot files included. But basically, you have to create a 100 MB EFI partition, format it with FAT32, and install the boot files.

    All boots have to be done to the UEFI version of the media, whether flash drive, Install DVD, or actual install. Using the F8 or F12 keys, or whatever your system used for a boot device menu, is usually best. Since the boot device can change, you need to choose it prior to every boot.

    Start by configuring the partitions on the new primary drive while still in Windows 7 using Disk Management. You can do this in Diskpart, but easier here. The end result has to be at least 100 MB of unallocated space on the drive.

    Now, shutdown and disconnect the old drive, and any external drives you don’t need. Reboot into the Install Media and go to the page where you would normally select to Install, but do not. Instead, use the Shift+F10 key combination to open a command prompt window.

    Type the following commands with enter after. Comments are for information, and not to be entered. You can use the first 3 letters of most words, except for Diskpart.

    Diskpart
    List Disk
    <- check for the drive you will be using and note the number.
    Select disk 0
    <- use the number for you drive, if using flash drive, be careful and don’t select it.

    Create partition efi size=100
    <- size= designation only used if more than 100 MB available. If you left exactly the correct room on the drive, remove the size=100.

    List Partition
    <- just to verify the correct partition is selected by checking for asterik on left.

    Format fs=fat32
    <- after creating a partition, it normally becomes the selected partition. If you want to make sure, use the List Partition command and then select the partition you need with select partition 3 for example. An asterisk on the left side will designate what is selected.
    Note: If a command you use shows Volume numbes instead of Partition numbers, Volume numbers and Partition numbers may not always agree, so use what is shown. If you select the wrong partition, you may wipe out your install.

    Exit

    We have left Diskpart, and back in the Command Prompt window. Now we need to put the boot files in the new partition. In the command prompt window, switch to the OS install partition, normally C: and it would be good to do a dir command and make sure the Windows folder is listed.


    C:
    Dir
    <-check for Windows folder. If another drive letter shows as the OS install use it in the next command.

    Bcdboot C:\Windows

    Wait for it to finish and give the successfully created message. You can now exit the install and should now be able to select the Windows Boot Manager during restart and boot into your Windows 7 install. If still not able to boot, do a Repair Install. See the attachment for actual command window.
    Attached Thumbnails Attached Thumbnails System won't boot after removing second hard drive, EFI?-dispart.jpg  
      My Computer

  9.    #9

    Good info, Saltgrass, tho I'm sure you're referring to Startup Repair - Run 3 Separate Times
    if it fails to boot, rather than a Repair Install.

    Does the SysReserved partition also need to be marked Active, as it does when constructing an NTFS System Reserved partition on an MBR disk?

    I recommend using free Partition Wizard bootable CD to shrink C from the left by 100mb+:
    Partition Wizard Move/Resize Partition Video Help.
    Partition Wizard Create Partition Video Help

    Finally, does this tutorial correctly show how to boot the installer to do these repairs and installation? UEFI (Unified Extensible Firmware Interface) - Install Windows 7 with - Windows 7 Forums
      My Computer


  10. Posts : 1,031
    Windows 7 x64
       #10

    gregrocker said:
    Good info, Saltgrass, tho I'm sure you're referring to Startup Repair - Run 3 Separate Times
    if it fails to boot, rather than a Repair Install.
    The Startup Repair is a little strange. I found booting to the Repair option first gave you a "Reoair and Restart" option. Allow that the first time, but say no the second time and continue to Startup Repair. The second run will fix the boot problem, so you only need two if you make these selections.

    gregrocker said:
    Does the SysReserved partition also need to be marked Active, as it does when constructing an NTFS System Reserved partition on an MBR disk?
    There is not an option to mark the EFI partition active. Linux does show it has a boot flag, but does not appear to use the same configuration. You cannot boot a GPT drive in an MBR system anywy.

    gregrocker said:
    I recommend using free Partition Wizard bootable CD to shrink C from the left by 100mb+:
    Partition Wizard Move/Resize Partition Video Help.
    Partition Wizard Create Partition Video Help
    gregrocker said:
    Finally, does this tutorial correctly show how to boot the installer to do these repairs and installation? UEFI (Unified Extensible Firmware Interface) - Install Windows 7 with - Windows 7 Forums
    The info on using the Boot device F key should be enough, but maybe more is needed. It is shown on the Tutorial you link, every bios setup is a little different as to how they handle the boot options. Looking for the UEFI version is necessary.

    Edit: I should be clear in this. Even if you leave space on the drive for the EFI partition, a Startup Repair will not repair the boot. All you will get is a compatibility error. You must make and probably format the EFI partition yourself. At least that is what my testing shows.
    Last edited by Saltgrass; 27 Jul 2012 at 17:39. Reason: More Info
      My Computer


 
Page 1 of 3 123 LastLast

  Related Discussions
Our Sites
Site Links
About Us
Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

© Designer Media Ltd
All times are GMT -5. The time now is 04:31.
Find Us