New
#1
1st Build - Major help needed
First of all I'd like to say that this is a GREAT forum and I've already received lots of help from a few choice individuals. Thank you sandeeP and TVeblen.
2nd, I will probably make this way too long. I apologize but I can't think of any other way to relate what has happened.
I tend to think my problems are because of the MB.
This is my first build. Desktop ~
- AMD A6-3500 Llano 2.1GHz (2.4GHz Max ...
- GIGABYTE GA-A75M-DS2 FM1 AMD A75 (Hudson ...
- Rosewill R363-M-BK Black Ultra High Gloss Finished ...
- G.SKILL Ripjaws X Series 8GB (2 x 4GB) ...
- Seagate NAS HDD ST3000VN000 3TB 64MB Cache ... x 2
The memory is not on Giga's approved list but memtest said they were fine.
I replaced the PSU that came w/the tower w/a Corsair CX500. (MUCH quieter) I also think the PSU was faulty. I had a lot of bizarre automatic reboots.
Originally I installed WHS using a retail disc. The board is, apparently, not compatible with WHS. I had tons of problems. The USB 3 on the board is not compatible w/WHS either. Nevertheless, I kept on installing. Common problem was using Win update and upon reboot having to go through System Repair. Then it would boot. Random restarts.
Ran the board outside the case, put it back in, would seem stable and then I'd get random restarts. I figured that this board just did not like WHS. I ran Fedora from a USB stick and it worked fine. Could not get it to crash.
Decided to put Win 7 pro on it. 3tb spinner and eventually I added the 2nd 3tb spinner. Had a copy from a laptop that died. It seemed to work OK. Did the massive Win update. Sometimes when I restart the PC it goes into Sys repair and I have to restore (while in Sys repair). Then it starts up and works just fine. This happened fairly often. Didn't really know what else to do so I just kept updating. Eventually it was stable.
I didn't do much with the PC. I have an extra SSD so I installed Win 7 on it. Awesome. Works. Did the billion updates. Occasionally I'd have to restart and I'd get the Sys repair/restore/restart/seems OK thing that had been happening before. Minimal software installed. Firefox, Samsung Disk utility and Crystal Mark.
Stable...on my LAN...using it as a small file server while I put SSDs in 2 other home PCs.
Seems OK.
There have always been 2 3TB Seagates in the tower. I plug in the SATA connector for 1 (NOTE: this HD did have Win 7 installed on it). I did not touch the SSD. Restart, go into BIOS to make sure it's booting to the SSD. Let it load. 'Reboot and Select Proper Media.
Added new/old HDs and now I get 'Reboot and Select Proper Media.' <-----7forum thread about this this problem.
I assume the spinner w/Win on it is messing up the boot. I plug in a SATA dvd so I can use gparted to nuke the 100mb win partition on the spinner. I'm assuming this will let the SSD boot.
System repair! Hardware change! Run system repair. 'sorry can't fix'. Shuts down.
Restart. 'Reboot and Select Proper Media..
Unplug everything but the SSD.
Sys repair.
Restarts.
Repeat about 3 times.
I'm told to change the on-chip SATA to AHCI. For some reason it's on IDE.
Change it to AHCI and then reinstall Win 7.
No....I go into a massive System repair/restore/reboot/cycle.
Eventually Win loads.
Plug in the DVD.
Hardware change and back into the System repair/restore/loop
Go into BIOS and hit 'load optimal settings'
I have no idea what to do so I move the SSD from SATA 0 to SATA 1 and it boots.
However...it's supposed to be in SATA 1
The BIOS has changed 'on-chip SATA' back to IDE. I'm not sure why that's optimal.
So I just rebooted the system again and SYSTEM REPAIR. It's going to the do the restore thing again and after a couple rinse/repeats it will boot normally. Eventually it will boot and go into System Repair. That's just what it does.
There are updates so I install them. It BSOD upon reboot. Go into System Repair/restore/cycle and after doing that 3 times and BSOD'ing (hardware change) I'm back in Windows again.
I've installed WHS and Win7 at least 4 times. I've installed HDs and SSDs and have had the same type problems.
Is it the BOARD!? I am no expert (duh) but I'm not completely clueless. I put SSDs in my wife's laptop and my laptop and got everything back working successfully but this tower is just kicking my butt.
Memory/cords are seated. I don't think the board is shorting out. New PSU seems to be fine. What could be going wrong. HOW can I install Win incorrectly when I'm using the DVD and basically just letting the system do it 's thing?
I did align/clean the SSD before installing Win on it.
I'm really at my wit's end here. All I can think of is taking the board out of the case and putting Win 7 on the SSD again but anytime I make any change to the board I get System repair and a system repair and then maybe it will boot correctly.
EDIT...and it just BSOD AGAIN. I did not touch it.
Last edited by ChrisPbass; 20 Dec 2013 at 16:19.