Windows 7 Forums

Welcome to Windows 7 Forums. Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks.


Windows 7: hp envy 6 1020sv fails win7 installation

13 Jan 2014   #11
fabio8v

win 7 ultimate 64 bit
 
 

I resolved..the problem wasn't the uefi but the management of the disk geometry that in this laptop change during the installation..to fix you have to download this driver and load during the installation..that's it..

http://www.intel.com/support/chipset.../CS-031502.htm


My System SpecsSystem Spec
.
17 Nov 2014   #12
myvegas

Windows 8.1 PRO 64 bits
 
 
HP Envy Sleekbook Touchsmart 4-1195CA Bricked and solved

Pls. refer to the following short tutorial without having to open the laptop

I have tried on my laptop HP Envy Touchsmart 4-1195CA.

1. ISO with Windows
1.1 Find a ISO with Windows 8 Pro for HP (you do not need to buy the HP Recovery Kit). Just look in internet en_windows_8_x64_dvd_915440.iso
1.2. Burn it to a USD 3.0 Pendrive (16Gb). Use rufus-1.4.12.exe.
1.3 Carefull with this. Setting for rufus GPT Partition for UEFI, FAT32. Otherwise it will not boot

2. Addtional Drivers
2.1 Download drivers from HP for Intel Rapid Storage (zip file)
2.2 Unzip and put those files within a folder in the Pendrive


3. BIOS.

3.1. Boot with pendrive and navigate the menu to access BIOS setup
3.2. Set USB 3.0 to auto mode
3.3. Enable legacy boo

3.4. DIsable SecureBoot
3.5 Change boot order for legacy boot. Place HD laptop in FIRST place


4. Delete RAID
4.1. With changes in item 3, should appear a new window on boot. Press ctrl+L for intel marix storage utility
4.2. Delete raid0 of ssd and hdd. Delete acceleration (press R)

Because you did 3 and 4, now all the disk drive will appear in windows installation.

5. Install Windows with pendrive
5.1 In storage WIndow to install windows you have to add Intel Rapid Storage driver
5.2 Kill all the partitions
5.3 Select 30Gb ssd as target

6. After Windows is installed
6.1 Disable legacy boot, enable back what was done with the BIOS
6.2 Install Intel Rapid Storage software in windows to create RAID 0


Y listo!!!!
My System SpecsSystem Spec
Reply

 hp envy 6 1020sv fails win7 installation




Thread Tools Search this Thread
Search this Thread:

Advanced Search




Similar help and support threads
Thread Forum
Error 9C59 : Installation of IE10 fails on Win7 Pro x64
Hi, installation of IE10 on Win7 pro x64 always fails with error code 9C59. "Help on this error" shows error code: "WindowsUpdate_00009C59" "WindowsUpdate_dt000" I have IE9 installed. What I tried by now: Installation of IE10 using Windows update.
Windows Updates & Activation
Error 9C59 : Installation of IE10 fails on Win7 Pro x64
I have tried to update to IE10 however I keep getting error 9C59 I have tried uploading my CBS file however it is 38Mb and too large to attach can someone please help me
Windows Updates & Activation
No USB driver for Win7 on an HP Envy h8-1414
I clean installed Windows 7 on a HP Envy Hp-1414 that came with Window 8 installed. Everything went well by following the guides offered by Teog and Brink. That is until I tried to use the front USB ports. They would not recognize any sort of USB device I plugged into them. I looked at...
Drivers
installation/upgrade fails
I have a netbook that came with the starter edition. I am trying to install the pro edition over it. The install dies and tells me I cannot install it and I need to select Windows Anytime Upgrade instead. However, that will not accept my license key from my pro edition. Am I stuck with a disk I...
Installation & Setup
USB installation of Win7 fails to create boot sector
Long story short, I ran the Win8 (64bit) dev install on top of my Win7 (64bit). I thought it would prompt me where to install it (I have 2HDDs in my laptop and no ODD). All was well, but I didn't really like the UI. No big deal, right? Just re-run the Win7 install and wipe out 8... Wroooong!...
Installation & Setup
Windows 7 installation fails
I have my current OS which is Vista ultimate and decided to upgrade it to windows 7. But first i reformatted my computer with a fresh installation of VIsta ultimate and then installing the drivers. And then i upgrade it to Windows 7. All went right, but then after that when i almost arrived at...
Installation & Setup


Our Sites

Site Links

About Us

Find Us

Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

Designer Media Ltd

All times are GMT -5. The time now is 21:26.

Twitter Facebook Google+



Windows 7 Forums

Seven Forums Android App Seven Forums IOS App