Windows 7 Forums
Welcome to Windows 7 Forums. Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks.


Windows 7: Speckles, Crashes, etc. in Windows 7 Media Center


22 Aug 2009   #1

Windows 7
 
 
Speckles, Crashes, etc. in Windows 7 Media Center

Speckles, Crashes, etc. in Windows 7 Media Center

OK, so I need a hero right now. Iím having graphics issues with my custom media center (no gaming whatsoever) running Windows 7 Ultimate RTM. Iíve tried everything I can think of over the last few weeks, all to no avail. No matter what I do, at least one of the following eventually happens, according to the rough probabilities noted:

1) It always reaches a state where the screen is lightly speckled, progressing to heavier speckles, and eventually to near total distortion (note that sometimes, however, it will jump straight to the total distortion phase and sometimes, the blue screen mentioned in #3 will occur before the speckles begin).
2) It often pops up the tray notification about the ďdisplay driver stopped responding and has recoveredĒ.
3) It sometimes results in a blue screen (usually after speckling a while, but sometimes beforehand) mentioning that an ďattempt to reset the display driver and recover from timeout failedĒ and referencing ďnvlddmkm.sysĒ.
4) It occasionally causes the screen to randomly flicker / flash.
5) It rarely causes the screen to black out, sometimes coming back on and sometimes not.

The issues most commonly occur while displaying the Favorites slideshow (i.e. Windows 7 Media Centerís screen saver) or while displaying the Now Playing collage of album art. Interestingly enough, though, it hasnít ever started during a movie, even a Blu-Ray or HD DVD.

Iíve tried three different graphics cards (8500GT, 8600GT, 9500GT) to drive my HDTV through my receiver via component video (I have no HDMI devices) and to drive my front panel via VGA (my case has a touchscreen display on the front). I should note that when each card is first installed, I get an initial error about how my video may not work as expected since I have less than 64 MB video RAM (I donít remember the exact message), but thatís obviously not accurate. I just click OK, move on, and it never shows again until I install a different card.

Iíve also tried using a 7300GS in conjunction with with one of the main cards and drove the front panel off this separate card. I hoped this might take some load off the main card if that was somehow a problem (donít know why it would have been, but was getting desperate). It didnít fix the problem coming out of the main card, but I was at least able to conclude that the issue doesnít affect the front panel if itís running off a separate card, but that both screens are affected when one card is doing double duty.

Anyway, here are the specific graphics card models Iíve tried:

1) 8600GT: eVGA 256-P2-N753-TR 256MB 128-bit GDDR3 (ordered a couple weeks ago to convert this box into a media center; this PC was originally built as a home automation server, and all other hardware components below are holdovers from when I originally built the PC for that purpose)
2) 8500GT: MSI NX8500GT-MTD256EH 256MB 128-bit GDDR2 Silent Heatsink (took out of my modified HP z558 to try)
3) 9500GT: Galaxy 95TGE8HUFEXX 1GB 128-bit DDR2 (went out and bought at Best Buy just to make sure this wasnít an 8-series issue)
4) 7300GS: XFX PVT72GWANG 256MB 64-bit GDDR2 (the one I used back when this was just a home automation server)

And here are my other hardware components:

1) Case: Moneual MonCaso 932B Black Aluminum 7" Touch Screen ATX
2) Power Supply: Scythe Kamariki 2 KMRK-450A-2 450W ATX12V
3) Motherboard: eVGA 122-CK-NF68-AR Intel LGA 775 NVIDIA nForce 680i SLI ATX
4) Processor: Intel Core 2 Duo E6600 Conroe 2.4GHz LGA 775 65W
5) Memory: Corsair XMS2 2GB 240-Pin DDR2 SDRAM DDR2 800 (PC2 6400) Dual Channel Kit
6) Hard Drive: Western Digital Raptor WD1500ADFD 150GB 10000 RPM SATA 1.5Gb/s 3.5"
7) Optical Drive: LG GGW-H20L Super-Multi Blu-ray Disc Burner & HD DVD Drive SATA Lightscribe
8) Display: Pioneer Elite PRO-710HD 64Ē Reference Monitor (at least it used to be a reference model J)
9) Receiver: Pioneer Elite VSX-49Txi THX Ultra 2 A/V i-Link Receiver

So what else have I tried (other than that mentioned above)? Well, I failed to take good notes along the way, but minimally, these efforts come to mind, and none of the efforts resulted in any substantial change to the systemís behavior pattern:

1) Installed old and new drivers ranging from version 181.71 to the latest version 190.62; also tried the version that came on each included installation CD; used Driver Sweeper between attempted version.
2) Have tried with one card doing double duty and have tried with separate cards driving the two displays; either way, the displays are used in extended desktop mode; each display has been tried as the primary.
3) Have tried all three PCI-E x16 slots; the 8500GT, 8600GT, or 9500GT, whichever was in at the time, has definitely been tried in all three slots; didnít try the 7300GS in all slots, but thatís likely irrelevant.
4) When only using one card, have tried it with and without the front panel being active; have tried it with the front panel turned off via the display settings and have also tried it disconnected altogether.
5) Originally had the 64-bit version of Windows 7 RTM installed; thought it might be a 64-bit driver issue, so I even did a clean install using the 32-bit version of Windows 7 RTM, but there was no improvement.

And with thatÖ HELP!!! Iíve wasted enough time trying to solve this. It shouldnít be this difficult, so I know one of you out there has a magic bullet for me, so pleaseÖ hurry and fire it my way!


My System SpecsSystem Spec
.

19 Sep 2009   #2

Windows 7 x64 Build 7600
 
 

Have you tried using a DVI->HDMI converter to connect the PC to your HDTV? This might be an interference issue. I've run into this sometimes when running VGA for my HTPC: all of the power wires, speaker wires, and video wires all entangled behind the TV cause distortion on the way. By using an HDMI cable you will be bypassing the analog aspect completely and should get no interference.

Also, you don't mention if you've tried VGA (I don't think... long post). Have you tried VGA from your card to the TV? Maybe it's an issue with the component video converter you are using.

Edit: about the crashes, I would go through the BIOS and make sure that any settings for your video card are set correctly.

Good luck!

Brian
My System SpecsSystem Spec
20 Sep 2009   #3

Windows 7
 
 

Problem solved a while back. Forgot to post update here since I never received any responses here. I just needed a motherboard BIOS update. For the best and quickest responses, always post to AVS Forum. Yes, even on PC issues.
My System SpecsSystem Spec
.


Reply

 Speckles, Crashes, etc. in Windows 7 Media Center




Thread Tools




Our Sites

Site Links

About Us

Find Us

Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

© Designer Media Ltd

All times are GMT -5. The time now is 06:36 PM.
Twitter Facebook Google+



Windows 7 Forums

Seven Forums Android App Seven Forums IOS App
  

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33