Turn Windows 7 Laptop into Wireless Repeater with One Wireless Adapter

Page 2 of 2 FirstFirst 12

  1. Posts : 1
    win 32
       #11

    wdmaocn said:
    Nowadays, wireless router is a basic device at home because wireless access point (AP) is required. Sometime, a wireless repeater is also needed in a big house especially that with a big yard. Actually, without wireless router, only a Windows 7 laptop can be turned into a WiFi hotpot or a wireless repeater. Many discussions can be found online regarding how to turn Windows 7 laptop into a WiFi AP or virtual WIFI hotpot, however, the internet surfing is based on a local area connection. If wanna extend a WIFI signal to an enhanced new wireless AP, generally two wireless adapters are considered.

    Here, differently, with only one wireless adapter but without 3rd-party software, we can setup a wireless repeater in a Windows 7 Home Basic or Home Premium laptop with only one wireless adapter. This can boost the wireless signal to smartphones, tablet computers, or other wireless devices. Also, the mobility and flexibility allow extending the signal to a yard or a garage conveniently as you want.

    It is known that a virtual wireless adapter can be created with a third party software or only Windows 7 built-in commands. But in Windows 7 Home Basic or Home Premium, usually the virtual wireless adapter cannot be created or a hosted network cannot be started. I found a specific approach to clear the issues.

    We can follow the steps (successful setup in my two Windows 7 Home laptops),

    1. Click Start, point to All Programs, click Accessories, right-click Command Prompt, and then click Run as administrator.

    2. A virtual wireless adapter can be created by command of,

    netsh wlan set hostednetwork mode=allow ssid=sameabcd key=12345678

    where sameabcd is your new ssid of the virtual AP, key is the password for virtual AP.

    If the virutal adapter named 'Microsoft virtual WiFi miniport adapter' cannot be created, we have a specific method here.
    Delete all temporary point to point ssid at Manage wireless networks in Network and Sharing Center, and change all static IP to dynamic IP. Then bridge Local Area Connection to Wireless Network Connection (see Fig. 1), again run the command above, usually, the virtual wireless adapter can be created. If not, update the driver of the wireless adapter. If no again, it means the wireless adapter does not support hosted network. When the 'Microsoft virtual WiFi miniport adapter' is created, delete the bridge immediately.

    Attachment 233430

    Fig. 1

    3. Start hosted network by

    netsh wlan start hostednetwork

    If the hosted network cannot be started, similarly, we still have a specific approach here.
    Delete all temporary point to point ssid at Manage wireless networks in Network and Sharing Center, and change all static IP to dynamic IP. Then bridge Wireless Network Connection to Wireless Network Connection 2 (as shown in Fig. 1), run the above command again, usually the hosted network can be started. Then delete the bridge immediately, and run the command again.

    4. Go to Control Panel > Network and Sharing Center > Change adapter settings. Right click on Wireless Network Connection and select Properties. Go to the Sharing tab and check "Allow other network users to connect through this computer's Internet connection." Then at the "Select a private network connection" drop down menu, select Wireless Network Connection 2 and click the OK button.

    5. Searching the new created wireless signal, you can now get your smartphone, tablet computer, or any wireless device connected to the new WiFi AP.

    If do not need wireless repeater, just stop it by

    netsh wlan stop hostednetwork

    to stop the wireless hosted network.


    This method is free and no any 3rd-party software is required.

    After you set up the hosted network for the first time, you can just start or stop it by running following two batch files as administrator.


    start.bat

    netsh wlan start hostednetwork


    stop.bat

    netsh wlan stop hostednetwork


    Or only one batch file as attached. Attachment 233431

    Hi I seam to be setting it up just fine with the netsh commands but I fear I might need to manually edit IP, Gatway on the 'Microsoft virtual WiFi miniport adapter' ? I dont know Im not sure could do with some help please.

    Im running windows 7 Ultimate 32bit.

    Im not connecting because any device to connect is trying to obtain IP address and gives up.

    Internet works on the usb wireless network connection 3.

    I found that I had to enable windows firewall before I could get sharing to work.

    I run comodo firewall and tried to disable that and leave windows firewall running.

    Some pics attached.

    Where do I start to look for the issue?

    Many thanks for looking.
    Attached Thumbnails Attached Thumbnails Turn Windows 7 Laptop into Wireless Repeater with One Wireless Adapter-p1.jpg   Turn Windows 7 Laptop into Wireless Repeater with One Wireless Adapter-p2.jpg   Turn Windows 7 Laptop into Wireless Repeater with One Wireless Adapter-p3.jpg   Turn Windows 7 Laptop into Wireless Repeater with One Wireless Adapter-p5.jpg  
      My Computer


  2. Posts : 1
    Windows 7
       #12

    That works like charm


    That was easy steps, works like charm, explained in the best ever possible way. many thanks
      My Computer


  3. Posts : 1
    7
       #13

    comodo firewall , what's that.

    only 1 DHCP in 1 network
      My Computer


 
Page 2 of 2 FirstFirst 12

  Related Discussions
Our Sites
Site Links
About Us
Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

© Designer Media Ltd
All times are GMT -5. The time now is 04:55.
Find Us