New
#21
It's this PC I'm using right now. When I set it to DHCP it works every time.
Code:C:\Windows\system32>netsh interface ip show config name="Pripojenie bezdrôtovej siete" Configuration for interface "Pripojenie bezdrôtovej siete" DHCP enabled: Yes IP Address: 192.168.1.4 Subnet Prefix: 192.168.1.0/24 (mask 255.255.255.0) Default Gateway: 192.168.1.250 Gateway Metric: 0 InterfaceMetric: 25 DNS servers configured through DHCP: 192.168.1.250 Register with which suffix: Primary only WINS servers configured through DHCP: NoneCode:C:\Windows\system32>netsh wlan show interfaces There is 1 interface on the system: Name : Pripojenie bezdrôtovej siete Description : Atheros AR9285 Wireless Network Adapter GUID : 63a0eab9-0113-453b-91ef-b4e9a20aa677 Physical address : 00:25:d3:83:67:04 State : connected SSID : tiba BSSID : 00:22:b0:9a:67:d9 Network type : Infrastructure Radio type : 802.11g Authentication : WPA2-Personal Cipher : CCMP Connection mode : Auto Connect Channel : 1 Receive rate (Mbps) : 54 Transmit rate (Mbps) : 54 Signal : 88% Profile : tiba Hosted network status : Not started
So only thing you want is:
It must always have ip address 192.168.1.4 (or at least always the same), so you can port forward afterwards?
Physical address : 00:25:d3:83:67:04
More common syntax is: 00-25-D3-83-67-04
All you have to do is:
That's all you have to do. It will still use DHCP but it always get the same IP address. When connected to work router or other hotspot.... it just gets a dynamic address from that dhcp server.
- If wireless with mac address 00-25-D3-83-67-04 connects to your home router .... it should give him address 192.168.1.4
So a much beter solution!
How to do it... with "dcp reservation" on router. Something like this Setting up DHCP Reservation on a Linksys wireless-N router
You posted many screenshots, for example:
It shows "network connections". Why in english? And all netsh commands gave english output as well!!
I'm dutch... all that output is in Dutch on my site!
Any other win7 windows that aren't translated?
http://www.t-mobile.cz/dcpublic/Navo...nk%202641B.pdf
page 32, but actual information is on page 33.
A couple examples:
- Everything in "Nástroje na správu" (screenshot)
- Almost everything in CMD
- Speech Recognition (but it states that it's not supported)
Example in CMD:
Code:Microsoft Windows [Version 6.1.7601] Copyright (c) 2009 Microsoft Corporation. Všetky práva vyhradené. C:\Users\Ondrej>if /? Performs conditional processing in batch programs. IF [NOT] ERRORLEVEL number command IF [NOT] string1==string2 command IF [NOT] EXIST filename command NOT Specifies that Windows should carry out the command only if the condition is false. ERRORLEVEL number Specifies a true condition if the last program run returned an exit code equal to or greater than the number specified. string1==string2 Specifies a true condition if the specified text strings match. EXIST filename Specifies a true condition if the specified filename exists. command Specifies the command to carry out if the condition is met. Command can be followed by ELSE command which will execute the command after the ELSE keyword if the specified condition is FALSE The ELSE clause must occur on the same line as the command after the IF. For example: IF EXIST filename. ( del filename. ) ELSE ( echo filename. missing. ) The following would NOT work because the del command needs to be terminated by a newline: IF EXIST filename. del filename. ELSE echo filename. missing Nor would the following work, since the ELSE command must be on the same line as the end of the IF command: IF EXIST filename. del filename. ELSE echo filename. missing The following would work if you want it all on one line: IF EXIST filename. (del filename.) ELSE echo filename. missing If Command Extensions are enabled IF changes as follows: IF [/I] string1 compare-op string2 command IF CMDEXTVERSION number command IF DEFINED variable command where compare-op may be one of: EQU - equal NEQ - not equal Press any key to continue . . .