Wireless Bridge won't allow Internet (or anything else)

Page 1 of 2 12 LastLast

  1. Posts : 4
    windows 7
       #1

    Wireless Bridge won't allow Internet (or anything else)


    Hello,

    Firstly I apologize, but if this has been posted and answered in a previous post I have not been able to find it, but then I'm a bit of a forum beginner so... *shrugs*

    Anyway, I just loaded my daughter's new computer with Windows 7. Everything was fine. I had a wired direct connection to my linksys router, downloaded updates, surfed the Internet. Life was large.

    But my home is a bit older, and her bedroom is upstairs, whereas my office is downstairs. So I use an external 3com wireless bridge, which connects to a cisco access point connected to my linksys.

    But when I do this, my daughter's PC doesn't recognize the network as my home network, but rather a public one, and won't give me access to anything outside her own computer.

    I can ping the 3com bridge from her PC, and from my own pc downstairs, so it's not the wireless connection, so I'm thinking it's something in Windows 7 that's not allowing traffic on what it's deeming to be a security risk network.

    I'm not as experienced as some when it comes to computers but is it possible that when you designate a network as your "home" network that Windows captures some information about that network? i.e. MAC addresses of your router etc, and so if you connect in a different way (via a bridge) it locks you out?

    *shrugs* Regardless of why it's doing this, I need to find a way to convince my computer that it's on the home network and it's safe to surf etc... Any help would be greatly appreciated, because at this point my only thought would be to re-load the computer again, but this time using the wireless bridge during the install rather than hooking it up after so that it's the "first" network Windows sees so that I can then designate it as the "Home" network.

    Once again, thank you in advance for any of your suggestions. :)
      My Computer


  2. Posts : 8,870
    Windows 7 Ult, Windows 8.1 Pro,
       #2

    I'm not a network bridge expert because I don't manage one but these might help.

    Create a network bridge

    Windows 7 Create network bridge - CNET Windows 7 Forums
      My Computer


  3. Posts : 548
    W7 Ultimate 64bit W7 Premium 64bit W7 Premium 32bit WXP Home 32bit
       #3

    jkada said:
    Hello,

    Firstly I apologize, but if this has been posted and answered in a previous post I have not been able to find it, but then I'm a bit of a forum beginner so... *shrugs*

    Anyway, I just loaded my daughter's new computer with Windows 7. Everything was fine. I had a wired direct connection to my linksys router, downloaded updates, surfed the Internet. Life was large.

    But my home is a bit older, and her bedroom is upstairs, whereas my office is downstairs. So I use an external 3com wireless bridge, which connects to a cisco access point connected to my linksys.

    But when I do this, my daughter's PC doesn't recognize the network as my home network, but rather a public one, and won't give me access to anything outside her own computer.

    I can ping the 3com bridge from her PC, and from my own pc downstairs, so it's not the wireless connection, so I'm thinking it's something in Windows 7 that's not allowing traffic on what it's deeming to be a security risk network.

    I'm not as experienced as some when it comes to computers but is it possible that when you designate a network as your "home" network that Windows captures some information about that network? i.e. MAC addresses of your router etc, and so if you connect in a different way (via a bridge) it locks you out?

    *shrugs* Regardless of why it's doing this, I need to find a way to convince my computer that it's on the home network and it's safe to surf etc... Any help would be greatly appreciated, because at this point my only thought would be to re-load the computer again, but this time using the wireless bridge during the install rather than hooking it up after so that it's the "first" network Windows sees so that I can then designate it as the "Home" network.

    Once again, thank you in advance for any of your suggestions. :)
    What model 3COM Bridge? Is it connected to the ethernet port of you daughters PC then wireless to the Cisco AP?

    Something like this perhaps?

    PC=>Ethernet=>3Com Bridge=>Wireless=>Cisco AP=>Ethernet=>Linksys.
      My Computer


  4. Posts : 4
    windows 7
    Thread Starter
       #4

    Yes, it's hooked up exactly like that.

    It's a 3Com 11a/b/g Wireless Workgroup Bridge (Model WL-560, 3CRWE675075)

    Also, the Cisco AP is a 350 Access Point. Just a B radio, but really, what more do you need to surf and read e-mail?

    Looking forward to your reply. :)
      My Computer


  5. Posts : 548
    W7 Ultimate 64bit W7 Premium 64bit W7 Premium 32bit WXP Home 32bit
       #5

    Does your daughter's PC get an IP address off the Linksys router the same as your wired PC? I want to make sure the connection is really bridged.
      My Computer


  6. Posts : 4
    windows 7
    Thread Starter
       #6

    I knew there was a piece of information I forgot to include... Yes. Her PC gets her IP address via DHCP, and it DOES successfully get a valid IP from the Linksys router. So there is at some point, communication from her pc to the router (and beyond, as I can see in the ipconfig information that comes from my ISP).
      My Computer


  7. Posts : 548
    W7 Ultimate 64bit W7 Premium 64bit W7 Premium 32bit WXP Home 32bit
       #7

    By the way: Welcome to Seven Forums!

    Ok, so at least it's getting the right DHCP responses. It looks like you just need to change the Network location.

    You should be able to change the location. Try this:

    Control Panel => Network and Internet => Network and Sharing Center => From there you should be able to change it to Private. Look for View your Active Networks. You should be able to click on "Public Network" and bring up a new window that will allow you to change the location to Private.

    You may also want to look at Change Advanced Sharing Settings (left side of the page) to make sure you have Network Discovery enabled. If it can't see the other devices it may throw it's hands up and just call it Public.
    Last edited by RedBirdDad; 01 Feb 2010 at 16:42.
      My Computer


  8. Posts : 8,870
    Windows 7 Ult, Windows 8.1 Pro,
       #8

    If you can't change the Network location the normal way this might help.
    Windows 7 Unidentified Network, Limited Access, No Internet Connection Problem Resolved
      My Computer


  9. Posts : 548
    W7 Ultimate 64bit W7 Premium 64bit W7 Premium 32bit WXP Home 32bit
       #9

    chev65 said:
    If you can't change the Network location the normal way this might help.
    Windows 7 Unidentified Network, Limited Access, No Internet Connection Problem Resolved

    Secondary Default GW of 0.0.0.0? Somebody's DHCP isn't playing by the rules...

    Come to think of it, I think I've seen that somewhere...
      My Computer


  10. Posts : 8,870
    Windows 7 Ult, Windows 8.1 Pro,
       #10

    It happens all the time with Win 7 apparently, there are other threads at Technet about this.
      My Computer


 
Page 1 of 2 12 LastLast

  Related Discussions
Our Sites
Site Links
About Us
Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

© Designer Media Ltd
All times are GMT -5. The time now is 08:13.
Find Us