Overclocking Site Solves Mystery Behind Higher Ivy Bridge Temperatures

Page 1 of 2 12 LastLast

  1. Posts : 71,977
    64-bit Windows 11 Pro for Workstations
       #1

    Overclocking Site Solves Mystery Behind Higher Ivy Bridge Temperatures


    Intel stepped up to the plate and seemingly hit a homerun with its Ivy Bridge architecture (which, by the way, is now showing up in retail). It's the first commercial processor to boast a 22nm manufacturing process and 3D transistors, a combination that ultimately leads to better performance with less power consumption than previous generation processors. At the same time, some have reported higher temps with Ivy Bridge compared to Sandy Bridge, and it could have to do with the way Intel attached the Integrated Heat Spreader (IHS).
    Read more at:
    Maximum PC | Overclocking Site Solves Mystery Behind Higher Ivy Bridge Temperatures
      My Computer


  2. Posts : 11,424
    Windows 7 Ultimate 64
       #2

    I would be very leery of an extra 20c anywhere in the processor chain. That bothers me and will keep me away from these chips no matter how well they perform. Seems odd that they use less energy but run so much hotter.
      My Computer


  3. Posts : 12,364
    8 Pro x64
       #3

    I was looking for an excuse not to upgrade my 2500K - this will do

    Upgraditis averted :)
      My Computer


  4. Posts : 1,660
    Windows 8 Pro (32-bit)
       #4

    Would it be possible to replace the thermal paste with a better type?
      My Computer


  5. Posts : 6,879
    Win 7 Ultimate x64
       #5

    FuturDreamz said:
    Would it be possible to replace the thermal paste with a better type?
    Not without removing the IHS and completely and totally voiding any warranty on the CPU, and even then it likely wouldn't help any. The way I understand it, it isn't the type of TIM used but that TIM was used in the first place and not solder.
      My Computer


  6. Posts : 1,653
    Windows 10 Pro. EFI boot partition, full EFI boot
       #6

    FuturDreamz said:
    Would it be possible to replace the thermal paste with a better type?
    I think Intel would use the best paste they could muster and their process for applying it would be more optimized than you could do. The real difference may be between using fluxless solder and paste TIM, for which you can do nothing about.
      My Computer


  7. Posts : 11,424
    Windows 7 Ultimate 64
       #7

    Then that begs the question of how much if it's a savings at all going away from solder and to TIM is costing. It would seem if they could lower the temps even half of the difference then we would gladly pay a few more dollars for lower temps? Hell make two models a soldered model for X amount more and a TIM model and lock down it's cores.
      My Computer


  8. Posts : 1,653
    Windows 10 Pro. EFI boot partition, full EFI boot
       #8

    The temps are lower for non-overclocked, which is most of the market. If the higher temps are due to just the change from solder to paste TIM, then it makes no sense for Intel to not solder the k series, though it would require different manufacturing. I think there must be more to this than just the TIM.
      My Computer


  9. Posts : 12,177
    Windows 7 Ult x64 - SP1/ Windows 8 Pro x64
       #9

    They will get a lot of bad press for not using solder in the K versions.

    After reading on the subject, there are a few that claim certain settings can reduce the temps a bit, still not ideal for an OC'ing version.
      My Computer


  10. Posts : 24,479
    Windows 7 Ultimate X64 SP1
       #10

    Intel bally-hoos over-clock-ability, makes a chip that overheats when done and voids the warranty if you do it.
    In reality even when I use software that kicks in the Turbo-boost my temps are well within reason, less than 60C. It is Prime95's and IBT's fault.
    In my experience it is only stressing that raises CPU temps, YMMV.

    smarteyeball said:
    I was looking for an excuse not to upgrade my 2500K - this will do

    Upgraditis averted :)
    LOL, that was easy.
      My Computer


 
Page 1 of 2 12 LastLast

  Related Discussions
Our Sites
Site Links
About Us
Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

© Designer Media Ltd
All times are GMT -5. The time now is 01:30.
Find Us